Ono Sokki GS-5100 User manual
（Resolution:10μm）
（Resolution:1μm）
（Resolution:10μm）
（Resolution:1μm）
InstructionsManual
■OmissionofIssuanceofCertificate
■Warranty
１．
２．
・
・
・
・
３．
Ⓒ
OverviewandFeatures
●
●
・
・
・
CAUTION
Measurement
①
②
MountingtoFixingDevice
●Mountingbysqueezingstem
Recommended tightening torque: 0.4 to 0.5N･m
+ 0.018
0
+ 0.018
0
φ15H7
●Mountingusingthefixingholesonthemainunit
°
μ
Approximately 0.2mm
M4
screw
Spring
washer
Recommended tightening
torque （N･m）
1.4
0.84
Fixing jig
(female screw)
Iron
Aluminum
M4 screw
(male screw)
Iron
Iron
Mounting
surface
Base bottom
ø15H7
ø17
ø18
1.5（slot）
24.5
25
Recommended collar size and material
Material: Brass
●Mountingbysqueezingstemusingcollar
①
②
③
Recommended screw : M4
Recommended tightening torque : 0.4 to 0.5N･m
M4
screw
Collar
7mm or less
・
22Ω
22Ω
A
B
C
D
E
F
SIG 1
SIG 2
+5V IN
No connection
COM
COM
R03-PB6M (Tajimi Electronics)
Linear gauge sensor
P
SIG 1
SIG 2
When pushing spindle in
P
=
40μm ：GS-5050/5100
P
=
4μm ：GS-5051/5101
P
SIG 1
SIG 2
When pulling spindle out
+5V
+5V
Frame ground
Connector outer tube
OutputConnectorPinAssignmentsandOutputCircuit
μ
μ
+5V
PrecautionsforUse
●
●
●
●
●
●
●
●
･
●
●
CAUTION
LINEAR GAUGE SENSOR 50mm
PartNames
ReplacingGaugeHead
･
① Φ
②
③
Round bar（Φ2 or less）
Spindle Gauge
head
Round bar
●
Aboutdust-protectiverubber
Troubleshooting
Causes CountermeasuresPhenomena
・
：
・
ApplicableStandards
OutlineDimensionalDrawing
●
●
124
30
7.5
2.52.5
36
17.5 56.5 31.511 138.5 (3.5)
(134.5)
258.5
φ6
45
φ11
φ4
36
45
φ15.5
34
10.5
12.5
18 (18)
22.5 (22.5)
10
φ2.2
Depth of counterbore (2-M4): 12
Mounting surface
LINEAR GAUGE SENSOR 50mm
LINEAR GAUGE SENSOR 100mm
φ15 0
-0.018
Tajimi Electronics
R03-PB6M
Cable length:
Approximately 4.9m
GS-5050 IP5X
NO.00000001
MADE IN JAPAN
GS-5100 IP5X
NO.00000001
MADE IN JAPAN
2.52.5
36
45
18 (18)
22.5 (22.5)
36
10
Mounting surface
7.5
Depth of counterbore (2-M4): 12
φ11
φ4
φ15.5
34
10.5
12.5
Tajimi Electronics
R03-PB6M
Cable length:
Approximately
4.9m
170.5
17.5 103 188.5 (3.5)
(184.5)
355
φ6
φ2.2
30
31.511
45
φ15 0
-0.018
GS-5051 GS-5101
DC 4.5 to 5.5 V
120mA or less (5VDC)
Two-phase square-wave signal
Phase difference 90°±20°
Approximately 22 Ω
・ Extension spindle : AA-844 (30mm) / AA-845 (50mm)
・ Finger lift : AA-969
・ Gauge stand : ST-0230/044B
・ Mounting bracket : AA-8560
・ Dust-protective rubber : AA-4106 (for GS-5050/5051)
●ElectricalSpecifications
●GeneralSpecifications
0 ℃ to +40 ℃
-10°C to +55°C (average annual humidity 75% or less) * No condensation permitted
Approximately 4.9m ＊3
Up to 30m ＊4
GS-5050/5051: Approximately 570g GS-5100/5101: Approximately 655g (including cable)
Instructions Manual (this manual) x1
IP-5X (Category 2) ＊5
GS-5100GS-5050
Operating temperature range
Storage temperature range
Cable length
Cable extension
Mass
Accessories
Protection Class
Options
* See the catalog
for details.
Items
Supplied power
Consumption current
Signal output
Output impedance
＊3 Signal cable connector disconnection or remodeling will invalidate CE marking.
＊4 20m when EMC applicable cable AA-8803 is used.
＊5 Category 2: Operation environment causing no pressure difference from atmospheric pressure
＊1 Value with our gauge counter used
A value enclosed in ( ) is the maximum response speed for DG-4140/4160.
＊2 Vibration/shock resistance of mechanical specifications during measurement are not guaranteed.
Specifications
Items
Measurement range（mm）
Resolution（μm）
Accuracy（μm）
Response speed（m/s）
Measuring force（N）
GS-5050
50
10
10
1 (4) ＊1
3
GS-5100
100
10
12
1 (4) ＊1
5.5
GS-5051
50
1
4
0.3 (1.2) ＊1
3
GS-5101
100
1
5
0.3 (1.2) ＊1
5.5
147 m/s2 in each of three axes (75 minutes per each), 10 cycles of 10 to 150Hz sweeping
1470 m/s2 in each direction for each of three axes, 3 times for each of ±X, Y and Z,
18 times in total, sine half-wave, 6ms operating time
● Mechanical Specifications
Vibration resistance
(Power OFF)＊2
Shock resistance
(Power OFF)＊2
This manual suits for next models
3
Other Ono Sokki Accessories manuals
