Opera AREA 930 User manual

AREA 930
Installation and User manual

25
CONNECTION TO THE POWER SUPPLY
The appliance may ONLY be connected by an authorized qualified technician.
Electric system protection should comply with all relevant regulations.
The connection clips can be accessed when the connection clip covers are opened /
removed.
Before connecting the appliance, make sure the voltage indicated on the rating plate is
consistent with the voltage in your home network. Connection voltage should be checked
by a qualified technician using a corresponding measuring device!
The rating plate with basic information is attached on the lower side of the appliance.
In order to make a fixed connection to the mains, insert an all-pole circuit breaker
between the appliance and the mains. This device shall have a contact separation in all
poles, providing full disconnection under overvoltage category III conditions.
The current conducting and isolated parts must be protected from any possibility of direct
contact.
Before any intervention, disconnect the appliance from the power mains. Connect the
appliance in compliance with the electric connections diagram supplied; make sure the
relevant network voltage is observed!
The ground wire should be connected to the clip indicated by the earth symbol.
The mains cable should be fed through the fastening clip which protects it from being
accidentally pulled out.
After connecting the appliance, turn on all cooking zones / heaters for approximately
three minutes to make sure they are operating correctly.
Incorrect connection may destroy parts of the appliance, making the warranty void!
Connection cable on the back of the appliance should be led in such way that it DOES
NOT touch the appliance back wall, as this part will get very hot during operation.
The appliance is generally configured to the maximum available power, shown in the
technical data table. It’s possible to set an operating mode with power limitation. This
setting can be made at the time of installation or subsequently by a specialized
technician. See chapter on power limitation setting.
Installation diagram
Use cables type: H05V2V2-F
LIVE
L1 – L2 – L3
BROWN – BLACK - GREY
EARTH
GREEN / YELLOW
NEUTRAL
N1 – N2
BLUE
Model Supply Voltage / Frequency Number of phases Power cable section Connection
7380645 220-240 V~ 50/60 Hz 1 phase + N 3 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 3 x 4 mm2
380-415 V ~ 50/60 Hz 2 phases + N 4 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 5 x 2,5 mm2
380-415 V ~ 50/60 Hz 3 phases + N 5 x 1,5 mm2
7381645
7381245
7382645
7383645
7384645

17
EN
Dear customer!
This appliance is intended for household use only.
Materials used for packaging are nature friendly and may be recycled, deposited or
destroyed without any threats to the environment. In order to recognize these features, all
packing materials are marked with relevant symbols.
Once your appliance has become obsolete and you do not intend to use it any longer,
take adequate care not to litter the environment. Deposit your old appliance with the
authorized depot dealing with used household appliances.
Instructions for use
Instructions for use describe the appliance and the way it is handled.
These instructions are intended for various types of appliances, so you can find some
descriptions of functions that your particular appliance may not have.
These instructions are only valid for the country indicated on the appliance. If there is NO
country on the appliance, technical instructions should be observed for adapting the
appliance to comply with the requirements and regulations in your country.
Instructions for
connection
The appliance must be connected in compliance with the instructions attached to it, as
well as in compliance with relevant regulations and standards. The connection may only
be performed by a qualified person.
Rating plate
The rating plate indicating the basic information is attached on the bottom of the
appliance.
The Manufacturer strives for continuous improvements. For this reason, the text
and illustrations in this book are subject to change without notice.
Keep these instructions in a safe place and ensure that new users are familiar with
the contents. Pass them on to any future owner.
Important warnings
18
Installation
19
Connection to the power supply
20
Tecnical information
21
Operation
23
Safety functions and error display
28
Cleaning and maintenance
29
1
3
5
7
8
21
22
Technical information
Appliance introduction

18
IMPORTANT WARNINGS
xThe appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements.
Children less than 8 years of age shall be kept away unless continuously supervised.
xPrevent the children to hang around the appliance and warn them properly against the danger of burns.
xThis appliance can be used by children aged from 8 years and above, and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
xChildren shall not play with the appliance.
xCleaning and user maintenance shall not be made by children without supervision.
xUnattended cooking with fat or oil can be dangerous and may result in fire. Be sure having the preparation of
such food (fries) under constant control. Never try to extinguish a fire with water, but switch off the appliance and then
cover flame e.g. with a lid or a fire blanket.
xDanger of fire: do not store items on the cooking surfaces.
xIf the surface is cracked, switch off the appliance to avoid the possibility of electric shock.
xDon’t use high-pressure steam cleaner or hot steam to clean the appliance.
xNever place any metal objects upon the appliance surface, such as knives, forks, spoons, pot lids, and the like, as they
may get very hot.
xThe appliance can not be activated by external timers or remote controls systems.
xDo not use the appliance for room heating.
xIf there is a wall power outlet located near the appliance and another appliance is plugged into it, make sure the power
cord does not come into contact with the hot cooking zones.
xDo not store any temperature-sensitive objects, materials, or substances underneath the appliance, e.g. detergents,
sprays, etc.
xIn case of a failure of the appliance, immediately disconnect the appliance from the power mains and contact the service
center.
xThe appliance is manufactured in compliance with the relevant effective safety standards.
xDon't connect the appliance to the power supply with an extension cable or multiple sockets, because they don't assure a
sufficient safety (e.g. overheating risk of multiple sockets).
xConnect the appliance to a permanent connection.
xInstallation of the appliance into a kitchen worktop and its connection to the power mains may only be performed by an
adequately qualified technician.
xDo not place empty pans on the appliance.
xAppliance surface should not be used as a worktop. Sharp objects may cause scratches.
xPreparing food in thin aluminum of plastic containers on the cooking zones is not allowed. Do not place any plastic
objects or aluminum foil on the appliance surface.
xAfter a prolonged use of cast iron plates, the area of the plate and the edge of the cooking zone may faded. Repair
service is not covered by the warranty.
xIf the appliance is built-in over an oven with a pyrolytic system, it should not be operated while the pyrolytic process is in
progress because it can trigger its overheating protection.
The symbol on the product or on its packaging indicates that this product may not be treated as
household waste. Instead it shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product. For more
detailed information about recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the product.
2

23
INSTALLATION
Important warnings
• Installation of the appliance into a kitchen worktop must be performed by an adequately qualified technician.
• Veneer or other finish of the piece of kitchen furniture into which the hob is to be built in should be treated with heat
resistant glue (100°C); otherwise, the worktop finish may be discolored or deformed.
• Ideally the appliance should be installed with plenty of space on either side. There may be a wall at the rear and a tall
unit or wall at one side. On the other side, however, no unit or divider should stand higher than the appliance.
NOT ALLOWED
NOT RECOMMENDED
NOT RECOMMENDED
RECOMMENDED
• The distance between the appliance edge and the adjacent tall kitchen furniture element should amount to no less than
250 mm.
• All sizes and distances to be taken for the proper functioning of the appliance are shown in figures below.
• The kitchen furniture element underneath the hob should not be fitted with a drawer. If the kitchen furniture element as a
horizontal partition wall, it should be installed no less than min 20mm from the lower surface of the appliance. The space
between the partition wall and the appliance must be empty; no objects should be placed into that gap.
• Hanging, or wall-mounted kitchen elements should be installed high enough not to interfere with the work process.
• A minimum safety distance must be maintained between the appliance and the cooker hood above it. See the cooker
hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available
or, if there are any flammable objects (e.g. utensil rails, wall units etc) above the appliance, a minimum safety distance
of at least 800 mm must be maintained between them and the appliance below.
• Fit the wall units and cooker hood before fitting the appliance to avoid damaging it.
• The front part must have an opening of no less than 5 mm.
• The appliance must not be installed over a fridge, fridge-freezer, freezer, dishwasher, washing machine, washer-dryer or
tumble dryer.
• Only ovens fitted with a cooling fan may be installed underneath this appliance.
• Before installing an oven, the rear wall of the kitchen furniture element should be removed in the area of the appliance
cut-out. Furthermore, a gap of at least 5 mm should be left at the front side.
a
≥ 800 mm
b
≥ 50 mm
c
≥ 20 mm
d
≥ 80 mm
e
≥ 5 mm
f
≥ 30 mm
g
≥ 250 mm
3

BUILT-IN SIZES
Installing the foam
gasket
(for glass appliances)
Before inserting the appliance into the opening in the kitchen worktop, the supplied foam
gasket must be attached to the lower side of the glass.
Do not install the appliance without the foam gasket!
The gasket should be attached to the appliance in the following way:
xRemove the protective film from the gasket.
xAttach the gasket to the lower side approximatelyA=2-3 mm from the edge. The gasket
must be attached along the entire length and should not overlap at the corners.
xWhen installing the gasket, make sure that the glass does not come into contact with any
sharp objects.
The fixing of the appliance to the worktop is achieved by using the brackets supplied in the accessory bag. After
applying the gasket and positioning the top in the recess hole, position the brackets and secure them using the screws
provided. Use the holes in the four corners of the hob.
7380645 7381645 7381245 7382645 7383645 7384645
A290
580 580 770 770 860
B
510 510 510 510 510 510
C270
560 560 750 750 840
D480
480
480
480
480
480
E55 mm 55 mm 55 mm 55 mm 55 mm 55 mm
F
6 mm 6 mm 6 mm 6 mm 6 mm 6 mm
GPP PP PP PP PP PP
HPP PP PP PP PP PP
24
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 20 of 113
There are three standard pot sizes implemented in the UI: small, medium, big. Pots are always displayed
with a round shape. Fourth pot size is only used in display conflict cases.
4.2.5 Pot Selection and Power Regulation
Precondition
The cooktop is switched on and a new pot is placed on the cooktop.
The pot is displayed in the main screen
The new pot will only be automatically selected by the system if no other pot has been selected
before
Selection mode is shown by a little animation with two function icons around the pot. Additionally, the
power level slider appears on the bottom part of the display
Select the desired power level on the slider
930
IAR093A0
520
905
490
4

5
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 20 of 113
There are three standard pot sizes implemented in the UI: small, medium, big. Pots are always displayed
with a round shape. Fourth pot size is only used in display conflict cases.
4.2.5 Pot Selection and Power Regulation
Precondition
The cooktop is switched on and a new pot is placed on the cooktop.
The pot is displayed in the main screen
The new pot will only be automatically selected by the system if no other pot has been selected
before
Selection mode is shown by a little animation with two function icons around the pot. Additionally, the
power level slider appears on the bottom part of the display
Select the desired power level on the slider
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 22 of 113
4.2.6 Shortcut switch OFF pot
To be able to switch off a pot really fast the user can double tab on the required pot. The power level is
immediately switched to power level 0.
Double tap on pot icon
Pot is selected and is then switched OFF.
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
Generally, two selection modes are possible:
Direct Selection:
The selection is done by touching directly on the desired cooking level number.
Sliding:
The selection is done by wiping with the finger from the left side to the right or vice versa.
The power level slider is visible if a pot is in selection mode.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 23 of 113
4.2.8 Power levels
In general, there are 18 power levels implemented in the power level slider.
[0, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9]
If a pot is selected, the display shows only full power level 0 on the slider. As soon as the user set power
level >0 a dot is displayed on the left and right side of the level to indicate half power levels.
The user can select half step power values by doing the following:
Select a half power level by touching between the power values shown in the slider
The requested power level 2.5 is set and displayed in the pot and slider
25
CONNECTION TO THE POWER SUPPLY

The appliance may ONLY be connected by an authorized qualified technician.
Electric system protection should comply with all relevant regulations.
The connection clips can be accessed when the connection clip covers are opened /
removed.
Before connecting the appliance, make sure the voltage indicated on the rating plate is
consistent with the voltage in your home network. Connection voltage should be checked
by a qualified technician using a corresponding measuring device!
The rating plate with basic information is attached on the lower side of the appliance.
In order to make a fixed connection to the mains, insert an all-
pole circuit breaker
between the appliance and the mains. This device shall have a contact separation in all
poles, providing full disconnection under overvoltage category III conditions.
The current conducting and isolated parts must be protected from any possibility of direct
contact.

Before any intervention, disconnect the appliance from the power mains. Connect the
appliance in compliance with the electric connections diagram supplied; make sure the
relevant network voltage is observed!
The ground wire should be connected to the clip indicated by the earth symbol.
The mains cable should be fed through the fastening clip which protects it from being
accidentally pulled out.
After connecting the appliance, turn on all cooking zones / heaters for approximately
three minutes to make sure they are operating correctly.
Incorrect connection may destroy parts of the appliance, making the warranty void!
Connection cable on the back of the appliance should be led in such way that it DOES
NOT touch the appliance back wall, as this part will get very hot during operation.
The appliance is generally configured to the maximum available power, shown in the
technical data table. It’s possible to set an operating mode with power limitation. This
setting can be made at the time of installation or subsequently by a specialized
technician. See chapter on power limitation setting.
Installation diagram
Use cables type: H05V2V2-F
LIVE
L1 – L2 – L3
BROWN – BLACK - GREY
EARTH GREEN / YELLOW
NEUTRAL
N1 – N2
BLUE
Model Supply Voltage / Frequency Number of phases Power cable section Connection
7380645
220-240 V~ 50/60 Hz 1 phase + N 3 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 3 x 4 mm2
380-415 V ~ 50/60 Hz 2 phases + N 4 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 5 x 2,5 mm2
380-415 V ~ 50/60 Hz 3 phases + N 5 x 1,5 mm2
7381645
7381245
7382645
7383645
7384645
25
CONNECTION TO THE POWER SUPPLY
The appliance may ONLY be connected by an authorized qualified technician.
Electric system protection should comply with all relevant regulations.
The connection clips can be accessed when the connection clip covers are opened /
removed.
Before connecting the appliance, make sure the voltage indicated on the rating plate is
consistent with the voltage in your home network. Connection voltage should be checked
by a qualified technician using a corresponding measuring device!
The rating plate with basic information is attached on the lower side of the appliance.
In order to make a fixed connection to the mains, insert an all-pole circuit breaker
between the appliance and the mains. This device shall have a contact separation in all
poles, providing full disconnection under overvoltage category III conditions.
The current conducting and isolated parts must be protected from any possibility of direct
contact.
Before any intervention, disconnect the appliance from the power mains. Connect the
appliance in compliance with the electric connections diagram supplied; make sure the
relevant network voltage is observed!
The ground wire should be connected to the clip indicated by the earth symbol.
The mains cable should be fed through the fastening clip which protects it from being
accidentally pulled out.
After connecting the appliance, turn on all cooking zones / heaters for approximately
three minutes to make sure they are operating correctly.
Incorrect connection may destroy parts of the appliance, making the warranty void!
Connection cable on the back of the appliance should be led in such way that it DOES
NOT touch the appliance back wall, as this part will get very hot during operation.
The appliance is generally configured to the maximum available power, shown in the
technical data table. It’s possible to set an operating mode with power limitation. This
setting can be made at the time of installation or subsequently by a specialized
technician. See chapter on power limitation setting.
Installation diagram
Use cables type: H05V2V2-F
LIVE
L1 – L2 – L3
BROWN – BLACK - GREY
EARTH
GREEN / YELLOW
NEUTRAL
N1 – N2
BLUE
Model Supply Voltage / Frequency Number of phases Power cable section Connection
7380645
220-240 V~ 50/60 Hz 1 phase + N 3 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 3 x 4 mm2
380-415 V ~ 50/60 Hz 2 phases + N 4 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 5 x 2,5 mm2
380-415 V ~ 50/60 Hz 3 phases + N 5 x 1,5 mm2
7381645
7381245
7382645
7383645
7384645
25
CONNECTION TO THE POWER SUPPLY
The appliance may ONLY be connected by an authorized qualified technician.
Electric system protection should comply with all relevant regulations.
The connection clips can be accessed when the connection clip covers are opened /
removed.
Before connecting the appliance, make sure the voltage indicated on the rating plate is
consistent with the voltage in your home network. Connection voltage should be checked
by a qualified technician using a corresponding measuring device!
The rating plate with basic information is attached on the lower side of the appliance.
In order to make a fixed connection to the mains, insert an all-pole circuit breaker
between the appliance and the mains. This device shall have a contact separation in all
poles, providing full disconnection under overvoltage category III conditions.
The current conducting and isolated parts must be protected from any possibility of direct
contact.
Before any intervention, disconnect the appliance from the power mains. Connect the
appliance in compliance with the electric connections diagram supplied; make sure the
relevant network voltage is observed!
The ground wire should be connected to the clip indicated by the earth symbol.
The mains cable should be fed through the fastening clip which protects it from being
accidentally pulled out.
After connecting the appliance, turn on all cooking zones / heaters for approximately
three minutes to make sure they are operating correctly.
Incorrect connection may destroy parts of the appliance, making the warranty void!
Connection cable on the back of the appliance should be led in such way that it DOES
NOT touch the appliance back wall, as this part will get very hot during operation.
The appliance is generally configured to the maximum available power, shown in the
technical data table. It’s possible to set an operating mode with power limitation. This
setting can be made at the time of installation or subsequently by a specialized
technician. See chapter on power limitation setting.
Installation diagram
Use cables type: H05V2V2-F
LIVE
L1 – L2 – L3
BROWN – BLACK - GREY
EARTH
GREEN / YELLOW
NEUTRAL
N1 – N2
BLUE
Model Supply Voltage / Frequency Number of phases Power cable section Connection
7380645
220-240 V~ 50/60 Hz 1 phase + N 3 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 3 x 4 mm2
380-415 V ~ 50/60 Hz 2 phases + N 4 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 5 x 2,5 mm2
380-415 V ~ 50/60 Hz 3 phases + N 5 x 1,5 mm2
7381645
7381245
7382645
7383645
7384645
1 2 3 4 5
1 2 3 4 5
IAR093A0
5

26
WARNING! THIS APPLIANCE MUST BE GROUNDED
The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective
earthing system, which complies with current local and national safety regulations.
You can access terminal block at the bottom of the appliance. Open terminal block with the use of a screwdriver with a
slotted tip. Make electrical connection as shown in the table above, depending on the model purchased and the type of
electrical connection.
Basic adaptation of environment sensors
After each connection to electrical network, basic adaptation is automatically performed which ensures the optimal
function of the sensors. All displays light up for a few seconds. During sensor adaptation, there must be no objects. If not,
the adaptation stops until you remove the objects. During this time you cannot use the cooking panel.
1 2 3 4 5
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 22 of 113
4.2.6 Shortcut switch OFF pot
To be able to switch off a pot really fast the user can double tab on the required pot. The power level is
immediately switched to power level 0.
Double tap on pot icon
Pot is selected and is then switched OFF.
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
Generally, two selection modes are possible:
Direct Selection:
The selection is done by touching directly on the desired cooking level number.
Sliding:
The selection is done by wiping with the finger from the left side to the right or vice versa.
The power level slider is visible if a pot is in selection mode.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 23 of 113
4.2.8 Power levels
In general, there are 18 power levels implemented in the power level slider.
[0, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9]
If a pot is selected, the display shows only full power level 0 on the slider. As soon as the user set power
level >0 a dot is displayed on the left and right side of the level to indicate half power levels.
The user can select half step power values by doing the following:
Select a half power level by touching between the power values shown in the slider
The requested power level 2.5 is set and displayed in the pot and slider
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 24 of 113
4.2.9 Power level display
Dependent of the status of the pot, the pot shape is changing its color.
Power level 0: Pot is displayed in blue
Power level 1 to 3.5: Pot is displayed in purple
Pot Programs: Pot is displayed in purple
Power level 4 to 6.5: Pot is displayed in red
Power level 7 to B: Pot is displayed in orange
Lifted pot: Pot is displayed in grey
4.2.10 Boost function
The booster enables the induction to provide a higher power for a pot than its nominal power for a short
period of time (10 min for Area induction). This is useful to heat-up/boil a big amount of water.
Note As the booster function may reach high temperatures, it must only be used for cooking
processes using water. Oil or fat may start to burn if booster is used.
ACTIVATION OF THE BOOSTER
Precondition
Cooktop is switched ON. Pot is placed on the cooktop and pot is in selection mode.
Select booster level on the slider (e.g., shown as “B” or “P”)
The booster for the selected cooking zone is activated. The display for the pot shows a boost sign.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 23 of 113
4.2.8 Power levels
In general, there are 18 power levels implemented in the power level slider.
[0, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9]
If a pot is selected, the display shows only full power level 0 on the slider. As soon as the user set power
level >0 a dot is displayed on the left and right side of the level to indicate half power levels.
The user can select half step power values by doing the following:
Select a half power level by touching between the power values shown in the slider
The requested power level 2.5 is set and displayed in the pot and slider
6

technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 34 of 113
LEAVING THE POT PROGRAMS
Pot Program can be exited
by touching the X icon
by the expiry of timeout counter
by touching the area above the pot program menu.
MELTING FUNCTION
The melting function is especially used for melting chocolate. The function sets the temperature of the
induction coil sensor to 44°C.
ACTIVATION OF THE MELTING FUNCTION
Precondition
Cooktop is ON. Pot is placed on the cooktop and pot program menu is opened
Select the chocolate icon
The melting function is activated for the selected pot
The pot is deselected
The program menu closes automatically
Note In most cases, the symbols / icons are displayed inverted for the duration of the actuation.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 37 of 113
KEEP WARM FUNCTION:
The function sets the temperature of the induction coil sensor to 70°C.
ACTIVATION OF KEEP WARM FUNCTION
Precondition
Cooktop is ON. Pot is placed on the cooktop and pot program menu is opened
Select the keep warm icon
The keep warm function is activated for the selected pot
The pot is deselected
The program menu closes automatically
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 24 of 113
4.2.9 Power level display
Dependent of the status of the pot, the pot shape is changing its color.
Power level 0: Pot is displayed in blue
Power level 1 to 3.5: Pot is displayed in purple
Pot Programs: Pot is displayed in purple
Power level 4 to 6.5: Pot is displayed in red
Power level 7 to B: Pot is displayed in orange
Lifted pot: Pot is displayed in grey
4.2.10 Boost function
The booster enables the induction to provide a higher power for a pot than its nominal power for a short
period of time (10 min for Area induction). This is useful to heat-up/boil a big amount of water.
Note As the booster function may reach high temperatures, it must only be used for cooking
processes using water. Oil or fat may start to burn if booster is used.
ACTIVATION OF THE BOOSTER
Precondition
Cooktop is switched ON. Pot is placed on the cooktop and pot is in selection mode.
Select booster level on the slider (e.g., shown as “B” or “P”)
The booster for the selected cooking zone is activated. The display for the pot shows a boost sign.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 23 of 113
4.2.8 Power levels
In general, there are 18 power levels implemented in the power level slider.
[0, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9]
If a pot is selected, the display shows only full power level 0 on the slider. As soon as the user set power
level >0 a dot is displayed on the left and right side of the level to indicate half power levels.
The user can select half step power values by doing the following:
Select a half power level by touching between the power values shown in the slider
The requested power level 2.5 is set and displayed in the pot and slider
SYSTEM POWER SETTINGS
•The cooktop must be connected to the power supply for max. 1 minute.
•The cooktop must be switched OFF.
•Press simultaneously anywhere on the left region and on the right region in the lower half area of the display for 2 seconds.
•Values starting from 2.4kW up to 11.0 kW in 100W steps can be chosen.
•Select the power level with the selection wheel and save with the confirm button.
TECHNICAL INFORMATION
IAR093A0
220-240 V 1N
380-415 V 3N
50 / 60 Hz
870 x 384 mm
11000 W
179,6 Wh/kg
2600 W
3650 W
7
MODEL
SUPPLY VOLTAGE
SUPPLY FREQUENCY
COOKING AREA
TOTAL POWER
EC ELECTRIC COOKING
ENERGY CONSUMPTION
FOR THE HOB [Wh/kg]
NOMINAL POWER
BOOSTER POWER

technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 26 of 113
4.2.12 Pot Lifting
If a pot is lifted by the user, the induction keeps the pot information for approx. 20 seconds. During that time
the user can replace the pot and all pot settings are reset automatically.
Lift pot
Pot is displayed as lifted. Pot information remains in the display for approx. 20 seconds
Active pot timer is paused
Replace pot on the cooktop
All pot settings are reset automatically
Notes If the pot is not replaced on the cooktop within 20 seconds, the pot display is removed.
If a new pot is placed in area of a lifted pot, this pot is deleted.
APPLIANCE INTRODUCTION
ON/OFF Key Display Cooking area
At the first connection to the power supply, or after an interruption and a restoration, the
display shows the factory preset time for about 20 seconds.
First Connection
Press the ON/OFF button to turn on the appliance. When turned on, the display shows
the initial screen accompanied by an acoustic signal.
Turning the hob ON
To turn off the device, press the ON/OFF button until an acoustic signal is emitted.
The current time is displayed for about 20 seconds.
Turning the hob OFF
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 22 of 113
4.2.6 Shortcut switch OFF pot
To be able to switch off a pot really fast the user can double tab on the required pot. The power level is
immediately switched to power level 0.
Double tap on pot icon
Pot is selected and is then switched OFF.
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
Generally, two selection modes are possible:
Direct Selection:
The selection is done by touching directly on the desired cooking level number.
Sliding:
The selection is done by wiping with the finger from the left side to the right or vice versa.
The power level slider is visible if a pot is in selection mode.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 42 of 113
4.4 Functions of menu bar
4.4.1 Key lock
Key lock is a functionality intended to lock the keys during the cooktop is in operation or in pause state. This
is useful for cleaning purposes (as the touch control is unable to differentiate a wet fabric from a finger).
Precondition
Cooktop is switched ON, no pot is selected
ACTIVATION OF KEY LOCK
Touch the Key Lock icon in the menu bar
The display screen except the Key Lock icon and the ON/OFF key are locked.
8