Opitec Incense Smoker User manual

1
ø15
ø20
Engineer´s File
Locking Clamp
118.473
Incense Smoker -
Little Wooden House
Part List Quantity Size (mm) Designation Part-No.
Wooden Board 3 150x100x10 Base Plate/ Front and Backside 1
Wooden Strip 1 300x60x10 Side Strips and Candleholder 2
Wooden Board 2 100x100x10 Roof 3
Wooden Strip 1 75x10x10 Gable 4
Wooden Strip 1 150x40x20 Chimney 5
Tealight Holder 1 Holder for Incense Cone 6
Thumbtack 2 Fixing of Tealight Holder 7
Tools Required:
Please Note!
Finished projects of OPITEC handicraft kits are not play toy articles in the same sense as general
commercially available ones, but rather are intended as teaching and learning material suppor-
ting educational objectives. The content of this construction kit may only be built and used by
children and adolescents under the guidance and supervision of qualified adults. Not suitable
for children under 36 months. Risk of suffocation!
Wood Glue +
All Purpose
Glue
Sandpaper Drill Bit Ruler
Fret Saw
Pencil and
Crayons
Mitre Box

2
1 2
Building Instruction 118.473
Incense Smoker - Little Wooden House
ø20 ø20
34
Transfer the template (page 5) for the walls of the house (1a + 1b) to
two wooden boards (1). Mark and drill the holes with the ø 20 mm drill
bit. Then saw out the door and the roof parts and clean the saw cuts.
1a 1b
2
2a
2b
2c
5a 5b
Mark the cut edges on the wooden strip (2) according to sizes (templa-
te page 4) and drill the two holes with the ø 20 mm drill bit. Then saw
out the side parts (2a + 2b) and the incense cone holder (2c) and clean
the saw cuts.
Cut the wooden strip (5) to size according to template (page 7). Then
bevel one exterior edge to 45° according to drawing. Clean the saw
cuts.
Part the wooden strip (4) as shown into 2 equal parts (template page
7) and clean the saw cut.
4
5
Glue together the walls of the house (1a, 1b, 2a, 2b) according to the
drawing and allow to dry well. Fix with screw clamps.
1b
1a
2a
6
Next take the engineer's file and file a notch at the center of one edge
of both of the two roof parts as shown in the drawing (approximately
as deep as the file depth).
2b

3
Building Instruction 118.473
Incense Smoker - Little Wooden House
8
Glue the two roof parts symmetrically to the house walls with the two
notches facing downwards (please refer to drawing!).
7
Glue the two strips (4) to one of the roof parts as shown. Allow the
glue to dry well.
12
On the last wooden board (1) mark the center and glue part 2c as
shown. Allow the glue to dry well.
9
Glue parts 5a and 5b together as shown and fix with the lock clamp
until the glue has dried completely.
10
ø15
On the upper side of the chimney mark the center by drawing the
diagonals and drill through using a ø 15 mm drill bit.
11
Glue the finished chimney to the roof using sucient glue for the glu-
eing to be tight, so later the smoke will not escape at the glued areas
but only through the chimney! Allow glue to dry well!
4
4
2c
1
5b
5a
5a 5b

4
Building Instruction 118.473
Incense Smoker - Little Wooden House
13
Attach the tealight holder (6) at the center of part 2c using the two
thumbtacks (7).
6
7
14
Place an incense cone at the center of the tealight holder, light it and
set up the little house. Finished!
Template Side Parts and Tealight Holder
M 1:2
2a
2c
2b

5
Building Instruction 118.473
Incense Smoker - Little Wooden House
Template Front and Backside
M 1:1

6

7
Building Instruction 118.473
Incense Smoker - Little Wooden House
Template Chimney and Gable
M 1:1