Opteev ViraWarn Plus 100 Installation and maintenance instructions

Getting started with ViraWarn
1 | P a g e
Table of Contents
Overview.......................................................................................................................................................1
Safety Precautions ........................................................................................................................................2
Unpacking the Box ........................................................................................................................................3
ViraWarn: Model Plus 100............................................................................................................................4
Assembling the Unit......................................................................................................................................4
Adding the Media..........................................................................................................................................4
Installation Location and Procedure.............................................................................................................5
Device Operation ..........................................................................................................................................7
Initialization..............................................................................................................................................8
Normal Operatoing Condition..................................................................................................................8
Overview
Congratulations on your purchase of a ViraWarn Plus 100 viral detection system. We thank you, and
we are here to support your effective use of the product. This document covers the ViraWarn Plus
100 unit.
Please use this document to properly operate your ViraWarn Plus 100 unit. For new ViraWarn
customers, we suggest you read through the entire document before starting. If you have experienced
the product, and only need specific instructions, please use the table of contents to navigate to the
information you need.
For any further assistance you can reach out to Opteev support team at [phone] or you can
send your queries at [email protected]m.
Let’s get started!
ViraWarn

Getting started with ViraWarn
2 | P a g e
Safety Precautions
The following points should be followed:
1. ViraWarn Plus 100 must only be used for the purposes described in this manual.
2. ViraWarn Plus 100 is intended for indoor use only.
3. ViraWarn Plus 100 should not be used or stored in direct or reflected sunlight.
4. ViraWarn Plus 100 should be operated and stored at temperatures between 50°F - 90°F (10°C -
32°C).
5. Store your ViraWarn Plus 100 unit in a clean and dry area.
6. Do not submerge ViraWarn Plus 100 in water.
7. Do not drop your ViraWarn Plus 100 unit.
8. Follow the instructions given in the manual to replace the refill bottles.
9. Do not disassemble ViraWarn Plus 100 unit.
10. Do not tilt ViraWarn Plus 100 unit after adding media in the detector chamber.
11. If you experience problems with your ViraWarn Plus 100 unit, contact Opteev support.
!IMPORTANT: The manufacturer reserves the right to alter the specifications of this product without
prior notice
Unpacking the Box
Your ViraWarn box should include:
•ViraWarn Plus 100 unit (Figure 1)
•One power cable
•One refillable detector chamber (Figure 2)
•Six refill bottles (Figure 3)
•ViraWarn Plus 100 Quick-Start Guide
Figure 1
ViraWarn: Model Plus 100
Figure 2
Sealed Detector Chamber
Figure 3
Refill bottles

Getting started with ViraWarn
3 | P a g e
ViraWarn Unit
Figure 4

Getting started with ViraWarn
4 | P a g e
Assembling the Unit
1. Remove the ViraWarn unit and a detector chamber from the
box.
2. Attach the detector chamber to the ViraWarn Plus 100 unit by
rotating it in a clockwise direction as shown in Figure 5.
3. Place the assembled unit on a sturdy platform, preferably on a
table or a desk.
Adding the Media
1. Remove two refill bottles from the ViraWarn box (Figure 6).
2. Rotate the cap to open the tube of one bottle/tube (Figure 7). (DO NOT throw away
the cap).
3. Invert and insert the bottle through the refill port and hold it a little bit up as shown in
Figure 8. Ensure the seal has been broken when inserted into the refill port. Before
removing it, make sure the tube is empty.
4. Empty the second bottle in the same manner.
5. Discard the empty refill bottle.
6. IMPORTANT: To achieve proper functioning, fill or refill the ViraWarn Plus 100 unit
using two (2) refill tubes
Figure 5

Getting started with ViraWarn
5 | P a g e
Installation Location and Procedure
WARNING: After adding the media, do not tilt the ViraWarn Plus 100 unit.
Maximum capacity of the detector chamber is with two refill bottles. Please do not overfill the
detector chamber.
Your ViraWarn Plus 100 unit comes with a power cord.
After adding the media, you can power up the ViraWarn unit by plugging the power cord into wall outlet
as shown in Figure 10. Note, the micro-USB portion of the power cord plugs in the bottom side of the
ViraWarn Plus 100 unit.
Figure 10

Getting started with ViraWarn
6 | P a g e
Device Operation:
Place ViraWarn Plus 100 unit on a steady flat surface and power it up by plugging the power cord into
a wall outlet.
The lights (LEDs) in the front indicate the states of various functionalities (Table 1) of ViraWarn.
INDICATION
COLOR
Power Input
WHITE
Media Level
WHITE (steady/blink)
Virus Detection
GREEN/RED (steady/blink)
ViraWarn uses different indications during initialization & normal operating condition.
Initialization:
Once the ViraWarn Plus 100 unit is powered on, it enters the initialization state.
1. There will be a one-time buzzer sound to indicate the initialization process.
2. The fan will run for ten (10) minutes in its default configuration, if the container is not empty
else it will run for five (5) seconds if the container is empty.
3. The power light will have a steady white glow indicating power input to your ViraWarn unit.
4. The media level indicator indicates the level of liquid media present in the detector chamber.
This light will be activated once the device exits the initialization phase.
5. The virus detection light is for viral load status in the closed room. During initialization this will
blink in green.
Table-1
Figure 11

Getting started with ViraWarn
7 | P a g e
Normal Operating Condition:
After initialization, the ViraWarn Plus 100 unit will enter its normal operating condition.
1. IMPORTANT NOTE! The fan will be automatically turned off after 10 minutes on the device.
2. The power light will have steady white glow if the unit has power; this does not mean the unit is
running and actively monitoring.
3. To reactivate your unit, cycle the power using the on/off switch on the power cord and a new 10-
minute monitoring cycle will begin.
4. The media level indicator light has two states:
a. Steady white: Liquid media is in acceptable level.
b. Blinking white: Liquid media is below acceptable level or detector chamber is empty. Your
ViraWarn Plus 100 unit will automatically turn off its functionality. In this case the detector
chamber needs to be refilled by following the steps as mentioned in ‘Adding the Media’.
5. The virus detection light has four states indicating safe or a contaminated environment. Table-2
explains the various states and actions to be taken by users if they encounter these cases:
Glow
Indication
Action to be taken
Steady Green
Safe airspace
No action is required
Blinking Red (Slow)
Possible contamination Level-1
User should be alert
Blinking Red (Fast)
Possible contamination Level-2
User should be alert
Steady Red
Virus Detection- contamination of
airborne viruses in the airspace
Evacuate the room, switch off the device for 30
minutes.
6. At the time of virus detection (indicated by Red light) the buzzer will be on and will be continued
for two minutes if the state of detection remains same.
Figure 12
Figure 13
Table-2