Optex Smartline Series User manual

-1-
INSTALLATION INSTRUCTIONS
No. 59-2069-0
INSTALLATIONS
PCU-5 ×1, Putty ×2
Power Convertor Unit
PCU-5
PARTS IDENTIFICATION
Voltage convertor unit used to enable wired
operation of the detector.
BATTERY OPERATED
PHOTOELECTRIC DETECTOR
Smart Line series
OPTION
BATTERY OPERATED
PHOTOELECTRIC DETECTOR
Smart Line series
OPTION
™
™
1 2 3 Connect the connector cable to the
terminals of PCU-5.
4 5
78 9
6
Note>>
Put the cables in order not to be caught
between the main unit and cover.
Using a screwdriver or similar tool, break
the knockout position in the back box as
shown.
Open the battery plate and then route the
control panel wires from the rear of the back
box through the knockout holes. Adjust the
wires so that they extend about 100 mm
from the holes.
Fill the holes with the wires using the
supplied putty.
Close the battery plate and connect PCU-5
male connector to the female connector of
the battery plate.
Route the three connectors of the back box
through the slit on the upper part of the
main unit.
Attach the connectors.
Insert PCU-5 into the slots on the back
box and then connect the wires to the
PCU-5 terminals.
Route connector cables (Alarm, Low battery
and Tamper) in the back box through the
hole to the battery box.
Controlpanel

-2-
SYSTEM DIAGRAM
FUNCTION TO TRANSMIT LOW-BATTERY SIGNAL
SPECIFICATIONS
DIMENSIONS
Unit: mm (inch)
Current draw
Power input
Output voltage
Output current
Alarm output
D.Q. output
Low battery output
Tamper output
Operating temperature
Operating humidity
Dimension
WIRING DISTANCE BETWEEN POWER
SUPPLY AND DETECTOR
0.33mm2(AWG22)
0.52mm2(AWG20)
0.83mm2(AWG18)
1.31mm2(AWG16)
180m (600ft.)
280m (900ft.)
450m (1,500ft.)
700m (2,300ft.)
1,200m (4,000ft.)
1,800m (6,000ft.)
3,000m (10,000ft.)
4,500m (14,500ft.)
10.5 - 30 VDC
80mA (max.)
Approx. 3.6 to 3.9 VDC
10mA (max.)
Form C relay ; 30VDC. 0.2A
Form C relay ; 30VDC. 0.2A
N.C. relay ; 30VDC. 0.2A
N.C. relay ; 30VDC. 0.2A
-20°C to 60°C (-4°F to 140°F)
95% (max.)
H×W×D mm (inch): 71 (2.8) × 53 (2.1) × 20 (0.8)
12VDC 24VDC
Wire size Power supply voltage
71 (2.8)
20 (0.8)
53 (2.1)
Receiver
Red
Black
Main unit
Yellow
Orange
Brown
Green
Blue
Purple
Gray
Power
Power
10 - 30V
Alarm
Back box
PCU-5
Control panel
+
Low battery
Tamper
DQ*
Alarm
Low battery
Tamper
DQ*
* The DQ function is not provided
with the SL-TNR.
Transmitter
Red
Black
Main unit
Blue
Green
Back box
Battery plate
PCU-5
BCU-4
Battery plate
PCU-5
BCU-4
Low battery signal
Control
panel
The low-battery signals are transmitted from the transmitter using IR
beams.
This function enables to eliminate the need to install a wireless transmitter
in the photoelectric transmitter.
–
C
NC
NO
C
NC
NO
C
NC
C
NC
+
–
C
C
NC
C
NC
C
NC
NC
OPTEX INC. (U.S.)
URL: http://www.optexamerica.com/
OPTEX DO BRASIL LTDA. (Brazil)
URL: http://www.optex.net/br/es/sec/
OPTEX TECHNOLOGIES B.V.
(The Netherlands)
URL: http://www.optex.nl/
OPTEX PINNACLE INDIA,
PVT., LTD. (India)
URL: http://www.optex.net./in/en/sec/
OPTEX KOREA CO.,LTD. (Korea)
URL: http://www.optexkorea.com/
OPTEX SECURITY Sp.z o.o. (Poland)
URL: http://www.optex.com.pl/
OPTEX (DONGGUAN) CO.,LTD.
SHANGHAI OFFICE (China)
URL: http://www.optexchina.com/
OPTEX CO., LTD. (JAPAN)
URL: http://www.optex.net/
OPTEX (EUROPE) LTD. /
EMEA HQ (U.K.)
URL: http://www.optexeurope.com/
OPTEX SECURITY SAS (France)
URL: http://www.optex-security.com/