Optimal Power RPSC5412 User manual

i
REDUNDANT POWER SUPPLY SYSTEM FOR
NETGEAR® RPS CAPABLE ETHERNET SWITCHES
MODEL NO. RPS5412
Redundant Power Supply
Manual
Revision B
July 2014
Optimal Power Supplies LLC
www.optimal-power.com
All manuals and user guides at all-guides.com
all-guides.com

ii
PROPRIETARY DATA
All data in this manual is proprietary and may not be disclosed, duplicated or used for
procurement or manufacturing purposes, without prior written permission by
OPTIMAL POWER SUPPLIES LLC
LIABILITY
DO NOT OPERATE OR SERVICE THE RPS5412 MODEL WITHOUT READING THIS
ENTIRE DOCUMENT FIRST
Optimal Power Supplies LLC is not responsible for any kind of damages sustained through the
use of this or any other Optimal Power Supplies LLC products. It is entirely the customer’s
responsibility to take all the necessary precautionary measures when installing this unit.
In the interest of improving internal design, operational function, and/or reliability, Optimal
Power Supplies LLC reserves the right to make changes to the products described in this
document without notice.
WARRANTY
1. Optimal Power®warrants its product models RPS5412 and RPSC5412 against defects in
materials and workmanship for Three (3) year from date of delivery. We will repair, or replace
parts which prove to be defective during the warranty period.
2. Any defect discovered after the warranty period has expired will be deemed to be outside the
coverage of the warranty, as noted below:
“THIS EXPRESS WARRANTY SUPERSEDES AND IS IN LIEU OF ALL REMEDIES AND
WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS, AND LIABILITY FOR NEGLIGENCE. IN NO EVENT SHALL SELLER OR
ITS DISTRIBUTORS BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL LOSSES,
EXPENSES OR DAMAGES”.
3. Optimal Power®does not endorse any other warranty, expressed or implied, and is not liable
for consequential damages. Products that are damaged, opened, or modified do not qualify for a
warranty. The same procedures must be followed for repairs outside the warranty period.
All manuals and user guides at all-guides.com

iii
CHAPTER
TITLE
PAGE
1
RPS Power Series –Introduction …………………………........................
1
1.1
Product Description…………………………………………………………..
1
1.2
Main Features…………………………………………………………………
1
1.3
General RPS Power Series Specifications…………………………………...
2
1.4
Typical Safety Rating………………………………..……………………….
2
2
RPS5412……………..…………..………………………………………...
3
2.1
RPS5412 Description………………..…….……………………………….
3
2.2
Specifications ………………………………………………………………...
3
2.3
Typical System Level Setup…..……………………………………………...
5
3
Status Indicators and Back Panel Connections……………………………
6
3.1
Back Panel DC Power Connector…………………………………………….
6
3.2
3.3
3.4
Front Panel Status Indicators…………………………………........................
Compatible NETGEAR® Switch Model Number Table.…….……………...
Model No. RPSC5412 (DC Connection Cable).……………………………..
6
6
7
4
Alarm Systems…………..…………………………………………………...
8
4.1
Alarm Monitoring System………………….………………………………...
8
5
Installation and Maintenance………………………………........................
9
5.1
Installation…………………………………………………………………....
9
5.2
Maintenance & Safety Instructions….……………………………………….
11
5.3
Trouble-Shooting Instructions …………………………………………….....
12
5.4
Warnings………………………………………………………......................
13
TABLE OF CONTENTS
All manuals and user guides at all-guides.com

1
Chapter 1
RPS Power Series - Introduction
1.1 Product Description
RPS Power Supply Series™ is a unique and a highly reliable power supply series. It is used as a
redundant power supply for NETGEAR® RPS capable PoE, 10/100 Ethernet, and Gigabit
Ethernet switches. The power supplies in this series are tested and verified by NETGEAR®.
The RPS Power Series™is designed for Universal AC to DC power supply applications.
Because of this feature these power supplies can be used anywhere in the world. These power
supplies are mainly used in the following applications:
Computer Peripherals and Networking Applications
Telecommunications and Fiber Optic Network
Voice, Data and Analog Communications
Universities and Educational Facilities
Instrumentation and Electronics
Utility and Power Industries
Data Acquisition
Medical
Military
The RPS Power Series™ is a reliable, efficient and inexpensive solution for all kind of AC to
DC power supply applications. Optimal Power®RPS units are intended for providing redundant
power to NETGEAR® switches.
1.2 Main Features:
Compact Rack Mount Size (1.75” H x 19” W x 12.12” D)
Universal AC (Alternate Current) Input
IEC AC Inlet Connectors
EMI FCC Class B Clearance for Internal Power Bricks
Single Port Output
Highly Efficient Design
1U Low Profile Height
NO Minimum Load Required
Output Voltage Status Indicator
Cost Effective and Reliable RPS Solution
All manuals and user guides at all-guides.com

2
1.3 General RPS Power Series Specifications:
Input Voltage………………………………...Universal 90VAC to 264VAC
Input Frequency……………………………...47Hz to 63Hz
Operational Temperature………………….…0°C to 55°C
Storage Temperature………………………..-20°C to 85°C
Cooling………………………………………Forced Air / Convection Cooling
Overload Protection………………………....Auto-Recovery
Efficiency…………………………………....80-90% Typical
DC OK………………………………………Status LED
1.4 Typical Safety Rating for Internal Power Supply Bricks:
Designed in full compliance with……...……UL60950
CSA 22.2 No. 234
EN60950
EMI………………………………..………...EN55022 “Class A”
EMS…………………………………………EN61000-4-2,-3,-4,-5,-6,-8,-11
Harmonics……………………………..….....EN61000-3-2 Class D
1U Power Supply
Shown above: Model RPS5412
All manuals and user guides at all-guides.com

3
Chapter 2
RPS5412
2.1 RPS5412 Description:
The Model RPS5412 is a 1U rack mountable RPS (Redundant power supply) designed to operate
with NETGEAR RPS capable switches. Model RPS5412 has built-in universal AC to –52V DC
and +12V DC power supplies with one IEC AC input socket. The Model RPS5412 can only be
connected to power a single NETGEAR® switch at a time. The RPS has an ON/OFF switch, and
an associating DC power LED.
2.2 Specifications:
Electrical
Output Voltage
–52V DC
+12V DC
Output Ripple
Typical 200mV
Typical 120mV
Output Current
Typical 6A max
Typical 9A max
Output Power
300W*
100W
Input Voltage
Universal 90VAC to 264VAC input
Input Frequency
47Hz to 63Hz
Input Current
Approx. continuous 5 Amperes
* NOTE: The Model RPS5412 only provides up to 300W for (Power-Over-Ethernet) POE application. If POE
devices connected to the switch system need more than 300W, then this device is not recommended.
Typical Safety Ratings for Internal Power Module:
Designed in full
compliance with
UL60950
CSA 22.2 No. 234
EN60950
EMI
EN55022 “Class A”
EMS
EN61000-4-2,-3,-4,-5,-6,-8,-11
Harmonics
EN61000-3-2 Class D
Environmental
Overload Protection
Auto-recovery
Functional Temperature
0 to 70 °C
Storage Temperature
-20 to 85 °C
Over voltage Type
Latch off
Efficiency
80-90% Typical
C
All manuals and user guides at all-guides.com
all-guides.com

4
Physical
Dimensions
1U (1.75” H x 19” W x 12.12” D)
Weight
Approx. 11.65 lb = 5.28 kg = 186.40 oz
Dimentional Figure
Overall Rear View
All manuals and user guides at all-guides.com

5
2.3 Typical System Level Setup:
An external Optimal Power®RPS unit can be connected to a NETGEAR® switch to provide
redundant power in case the primary power supply connected to the NETGEAR® switch fails.
The RPS can be setup is different configurations. However, a typical system level setup is as
shown:
RPS5412
Internet
LAN
WAN
Cable Modem / Router
Power Generator or
UPS
AC Input
–52VDC
Output
NETGEAR®
PoE Switch
WiFi
Wireless
Utility Power Company
Data
Primary
+12VDC
Output
All manuals and user guides at all-guides.com

6
Chapter 3
Status Indicators and Back Panel Connections
3.1 Back Panel DC Power Connector for RPS
Pin Numbers
Signal Name
Function
Pin 7
RPS Present
Logic Low = RPS Present
3.2 Front Panel Status Indicators
LED
Description
Solid Green
DC Power Supply Status
3.3 Compatible NETGEAR® Switch Model Number Table
Compatible NETGEAR® Switch Model Number Table
NETGEAR®
Switch Model
Optimal Power®
RPS Models
Optimal Power®
DC Cable
GSM7224-200
RPS5412
RPSC5412
GSM7248-200
RPS5412
RPSC5412
GSM7228PS
RPS5412*
RPSC5412
GSM7252PS
RPS5412*
RPSC5412
GSM7328S-200
RPS5412
RPSC5412
GSM7352S-200
RPS5412
RPSC5412
GSM7328FS
RPS5412
RPSC5412
GSM7212F
RPS5412
RPSC5412
GSM7212P
RPS5412
RPSC5412
GSM7224P
RPS5412
RPSC5412
* NOTE The Model RPS5412 only provides up to 300W for POE application. If POE
devices connected to the switch system need more than 300W, then this device is not
recommended.
–52V
RTN
–52V
–52V
7
–52V
RTN
GND
GND
GND
+12V
+12V
+12V
WARNING:
Observe polarity when making
connection to the rear of the RPS
Model RPS5412
Note: Refer to next 2 pages for DC
cable connections
All manuals and user guides at all-guides.com

7
3.4 Model No. RPSC5412 (DC Connection Cable)
Package Content
Redundant Power Supply Model RPS5412
DC Connection Cable Model RPSC5412
AC Connection Cord (see ordering chart)
Installation Manual
Rack-mount Screws
Ordering Information Chart
RPS Model
Worldwide region
RPS5412-100NAS
Americas
RPS5412-100EUS
Europe
RPS5412-100AJS
Asia
15
14
1
2
7
8
9
1
15
16
8
2
3
4
5
6
7
8
14
13
12
11
10
9
RPSC5412
NETGEAR® Switch Side Connector
RPS5412 Side Connector
All manuals and user guides at all-guides.com

8
Chapter 4
Alarm Systems
4.1 Alarm Monitoring System
The RPS Model RPS5412 has the ability to monitor output DC voltage. If the front panel Green
LED is ON that indicates good AC input and good DC output. When the Green LED is OFF that
indicates the following:
No AC voltage input
Low DC voltage output
No DC voltage output
All manuals and user guides at all-guides.com
all-guides.com

9
Chapter 5
Installation and Maintenance
5.1 Installation
Rack Mounting of Systems
Observe the following precautions for rack stability and safety. Also refer to the rack
installation documentation(s) provided by rack manufacturer. Systems are considered to
be components in a rack. Thus, "component" refers to any system as well as to various
peripherals, products or supporting hardware. Please adhere to the following instructions
when installing the RPS system:
After installing components in a rack, never pull more than one component out of
the rack on its slide assemblies at one time. The weight of more than one extended
component could cause the rack to tip over and may result in serious injury.
Components should be installed in a rack by trained service technicians.
Do not move racks by yourself. Due to the height and weight of the rack, a
minimum of two people should accomplish this task.
Always load the rack from the bottom up, and load the heaviest item in the rack
first.
Make sure that the rack is level and stable before extending a component from the
rack.
Do not overload the AC supply branch circuit that provides power to the rack.
The total rack load should not exceed 80 percent of the branch circuit rating.
Ensure that proper airflow is provided to components in the rack.
Do not step on or stand on any component when servicing other components in a
rack.
The system chassis must be positively grounded to the rack cabinet frame. Do not
attempt to connect power to the system until grounding cables are connected.
Completed power and safety ground wiring must be inspected by a qualified
electrical inspector. An energy hazard will exist if the safety ground cable is
omitted or disconnected.
Mounting Instructions
Before you install the RPS Power Supply, consult Section 3.3 of this manual to confirm
that your switch supports the OPTIMAL POWER®RPS Series Model RPS5412.
Installing the RPS Power Supply on a Flat Surface
You can install the RPS5412 (Redundant Power Supply) RPS on any appropriate level
surface that can safely support the weight of the switches, the RPS Power Supply, and
their attached cables. There must be adequate space around the RPS Power Supply for
All manuals and user guides at all-guides.com

10
ventilation and to access cable connectors. Consider following steps to install the RPS
system on a flat surface.
Set the RPS Power Series RPS on the flat surface and check for proper ventilation
and air flow.
Allow at least 2 inches (5.1 cm) on each side for proper ventilation and 5 inches
(12.7 cm) at the back for AC and DC power-cord clearance.
Attach rubber feet on the bottom of the chassis to keep the unit from slipping.
Installing the RPS Power Supply in a Rack
The RPS Power Supply can be installed in most standard 19-inch racks. Consider
following steps to install RPS Power Series RPS in rack.
Use appropriate size screws to attach the RPS system to the 19-inch rack.
Position the RPS Power Series RPS in the rack and align the oval shaped holes on
the side of the RPS with the holes in the rack.
Insert and tighten two screws appropriate for your rack through each of the oval
shaped holes on the side of the RPS.
To Operate the RPS Power Supply after Installation
Model RPS5412 may be installed in environments that meet the environmental
characteristics specified in Chapter 2. It is recommended that sufficient ventilation gap be
provided above or below the RPS unit for proper air flow.
Once the RPS (redundant power supply) is mounted in the rack, it should be connected to
a switch (that only requires –52VDC or +12VDC power),and has a DC connector
located on rear panel as shown:
The figure shows where to connect the Optimal Power® RPS Model RPS5412 on the
NETGEAR® switch.
Note: The location of the redundant power supply connector on your switch may differ from
the illustration.
RPS
DC Connector on NETGEAR®
switches for Optimal Power®RPS
Power Supply Series™RPS
DC Connector on the
switches is behind a
metal cover plate
NETGEAR® Switch
RPS Connector
All manuals and user guides at all-guides.com

11
Next follow the instructions below:
To connect a redundant power supply (RPS) unit to the switch, first turn "OFF"
the NETGEAR® Ethernet switch.
Also, ensure that the power switch on the RPS unit RPS5412 is in "OFF" position.
Important Note: Always Turn "OFF" the AC power first when installing or
removing the RPS from the system. RPS device should not
be live inserted. That is, when AC is "ON" DONOT
connect the RPS cable to the RPS connector on the switch.
When the power is "OFF", you can remove the cover plate on the rear panel of the
NETGEAR® switch as shown on the previous page.
Now connect the RPS DC Connection Cable Model RPSC5412 to the appropriate
NETGEAR® PoE switch making sure the connections are well secured, and the
AC power is "OFF" to the switch and the RPS.
Connect the AC power cord to the RPS unit by plugging the free end of the power
cord into a standard three prong AC outlet.
Ensure that the AC power plug located at the rear end of the power supply is
connected to a clean and well-grounded Universal AC source.
Once all the wires are connected properly, Turn "ON" the rear panel switch for
the RPS (redundant power supply) unit.
The Green LED should light up. Indicating Power supply is “ON” and working
properly. Now the system is ready to operate to its required purpose.
5.2 Maintenance & Safety Instructions
Please use the following safety instructions to ensure your own personal safety and to help
protect your system from potential damage.
The Model RPS5412 should be treated with the sufficient care.
Do not open, service (or) repair any product by yourself.
Do not use abrasives or solvents, as they may mar surfaces.
Do not subject the unit to excessive temperature extremes.
Do not subject the unit to excessive moisture or spilled liquids.
Do not expose your system to direct heat, radiators, rain, dripping or splashing.
Do not subject the unit to sudden or severe shocks.
Never operate the Model RPS5412 with any of the covers removed.
Do not block cooling vents.
WARNING: Observe polarity when making connection to the rear of
RPS Model RPS5412
All manuals and user guides at all-guides.com

12
Do not push any objects into the openings of your system. Doing so can cause fire or
electric shock by shorting out interior components.
Use the product only with approved equipment.
Operate the product only from the type of external power source specified.
Use only approved power cable(s). If you have not been provided with a power cable
contact OPTIMAL POWER®.
To help prevent electric shock, plug the system and peripheral power cables into
properly grounded electrical outlets. Provided AC cable is equipped with three-prong
plugs to help ensure proper grounding.
Do not use adapter plugs or remove the grounding prong from a cable. If you must
use an extension cable, use a 3-wire cable with properly grounded plugs.
Observe extension cable and power strip ratings.
Make sure that the total ampere rating of all products plugged into the extension cable
or power strip does not exceed 80 percent of the ampere ratings limit for the
extension cable or power strip.
To help protect your system from sudden, transient increases and decreases in
electrical power, use a surge suppressor, line conditioner, or uninterruptible power
supply (UPS).
Position system cables and power cables (AC and DC) carefully; route cables so that
they cannot be stepped on or tripped over. Be sure that nothing rests on any cable.
Do not modify power cables or plugs.
Install the power supply before connecting the power cable to the power supply.
Unplug the power cable before removing the power supply.
If the system has multiple sources of power, disconnect power from the system by
unplugging all power cables from the power supplies.
A qualified electrician must perform all connections to AC and DC power and to
safety grounds. All electrical wiring must comply with applicable local or national
codes and practices.
Never defeat the ground conductor or operate the equipment in the absence of a
suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available.
5.3 Trouble-Shooting Instructions
If the RPS system is not working, check the following steps before calling the Authorized
Technician at Optimal Power®:
Check that Green Status LED is "ON".
Check that AC input power exists and that main switch is in the "ON" position.
Check that the required 6A@250V fuse at the back of the RPS is not blown.
Check that all the RPS DC Connection Cable Models RPSC5412 are connected and
well secured.
If after all these trouble shooting steps the unit does not start, do not try to repair the unit but call
the Technical Support.
All manuals and user guides at all-guides.com

13
5.4 Warnings
To reduce the risk of fire, electric shock or product damage, DO NOT expose the Model
RPS5412 to direct heat, rain, moisture, dripping or splashing. DO NOT place any object filled
with any kinds of liquids on the unit. To prevent damage to LEDs and switches, DO NOT place
the front panel of the unit face down. DO NOT press against the front and/or rear panel.
Optimal Power Supplies LLC is not responsible for any kinds of damages (direct or indirect)
sustained through the use of any of its products.
______________________________________________________________________________
All manuals and user guides at all-guides.com
all-guides.com