OR STEEL light BELUGE 230VAC User manual

TECHNICAL MANUAL
The Beluge shaft mounted LED marker light is composed of a head high on a
flexible shaft so that it can be swivelLED towards the object to be lit. Its powerful
LED light makes this marker light perfect for lighting access roads, paths, stairs,
landscaped gardens, small trees... It has been designed with landscape architects
in mind and blends perfectly into all your green spaces.
BELUGE
230VAC
POWER 2,5W
SUPPLY 230VAC
POWER
SUPPLY
Included
WIRING Parallel
Electrical features
SIZE 22x40mm
WEIGHT 0.72KG
MATERIAL Brass -Bronze
OPERATING
TEMPERATURE
- 20°c ~+ 60°
PROTECTION RAITING IP68
RESISTANCE INDEX IK10
APPLICANCE CLASS CLASS II
WALKOVER FIXTURE NO
DRIVE-OVER FIXTURE NO
Mechanical characteristics
General characreristics
POWER SUPPLY
CABLES
Supply wire 2x1 mm2
in IP68
PHOTOBIOLOGICAL
SAFETY
Risk group I
ENERGY CLASS A /A+/A++
All data are given for information purposes only. They do not constitute a contractual commitment on our part and are subject
to change at any time.
T° max 55°C
AA+
A++
IP68
NGR
IK10
0,72
AVERAGE LIFE OF THE
LED
60 000 hours
Certicated L90 B10
COLOUR EMISSION 2700K - 3000K -
4000K - 6000K
RED - GREEN
BLUE - AMBER
BEAM 6°-25°-40-115°
INITIAL OUTFLOW 237lm at 3000k
Characteristics
lighting techniques
TECHNICAL SHEMATICS
INSTALLATION SHEMATICS
4040
2222 sosortiertie
IP68
Connecteur
1
4
4
3
IP67
IP68
Connecteur
3
IP67 IP68
3
12
3
Parallel wiring 230VAC
Two people are needed to install the
projector, one person wraps it around
the shaft, while the other holds the
projector head.
Never rewind
a projector
already
installed.
Not submerged
USE A IP68 CONNECTOR

1. Use
With 1 powerful LED, it can illuminate driveways, pathways, stairs, landscaped
gardens, small trees, etc. Specially intended for landscape gardeners, it will blend
perfectly into your outside spaces. Only an IP68 connection to the electricity
network ensures the IP68 degree of the product. Characteristics Assembly/
specific applications available on request.
2. Technical data
Projector with one 2,5W LED cold white (6000 K), neutral white (4000 K), warm
white (3000 K), red, green, blue and amber Diffusion of light by a 6° 25° 40° and
115° LEDS, 316L stainless steel gland. Delivered with 2x1mmSubmersible cable.
3. Installation/assembly
Please comply with the applicable national safety requirements. We disclaim
all responsibility for non-compliant use or assembly. Similarly, we reject any
responsibility for any modifications you may make to the light fittings.
For their use, constant current spotlights must always be connected in parallel
to the corresponding DC power supply (see power packs) (230VAC). We cannot
supply universal installation instructions because ground conditions and the
location will vary for each project.
The pictograms show examples of typical installations.
When mounting on a reinforced bracket, you must remove the screws.
Remove the projector from its support and direct it toward the object to be lit.
Then fix to the bracket using the A4 stainless steel screws provided. Use only
the factory-connected cables. Please indicate the required cable length when
ordering. In the event of mechanical stress, the cable must be installed in a
protective conduit.
The silicone cable must only be connected to the power supply in a dry environment
and, in the event of a direct connection in the ground, only connection units
compatible with a joint sealing compound should be used.
Connect the various conductors to power supplies in accordance with instructions.
4. Connecting to the power packs/connection matrix
Constant voltage headlamps should only be connected in parallel. If necessary,
connect in parallel in separate distribution boxes, the outside of which must also
be protected against humidity using a sealing compound.
5. General Maintenance Instructions
Do not use detergents which are harmful to metals when cleaning the spotlight.
The use of hydrochloric acid-based detergents on and around any parts of a
stainless steel light fitting is totally forbidden.
Regularly clean the spotlight and its mounting box to avoid any rust deposit
Caution: Do not use a high pressure cleaner. Caution: Protect the spotlights from
frost; where appropriate, dismantle or ensure special protection. Any lost screws
must be replaced by stainless steel V4A screws. According to conditions of use
(power, environmental circumstances), it is recommended to change the seals
(on the glass, screw fittings and O-rings) and the cable every 5 to 8 years.
6. Warranty conditions
The following time limits and provisions of the warranty shall apply from
the date of delivery: - 24 months for Orsteel spotlights. The warranty covers
defects in materials, manufacturing defects and any treatment which is proven
to be attributable to the manufacturer. Any damage resulting from the non-
compliance with this user leaflet or any non-compliant repair is excluded from the
warranty. We disclaim any guarantee where the installation has not been carried
out according to the instructions or where unsuitable bulbs or connection cables
have been used. We reserve the right to make any modification corresponding to
technical advancement.
7. Important Notice
(The warranty becomes void in the event of non-compliance with the following
points)
The absence of damage during transport must be verified before installation.
Any assembling and installation, as well as any electrical work, must be carried
out by qualified personnel.
To avoid any rust deposits, only stainless steel tools should be used.
The cable length for lamps must be chosen to avoid extending it in water or in a
damp environment. Any subsequent claim for this reason will not be accepted.
A mounting distance of 10 cm between each device is strongly recommended to
avoid mutual heating.
Equipment must be connected without current, otherwise surges in the power
supply could damage the LEDS. There must be no primary voltage when changing
LEDs.
When connecting the lamps, please ensure that polarity matches! A polarity error
may damage the LED module.
The customer is advised to install protection against any over voltage compliant
with standards DIN VDE 0100-443, DIN VDE 0100-534 and En 62305.
INSTALLATION GUIDE