OR STEEL light TULIPA User manual

TECHNICAL MANUAL
The very stylish Tulipa shaft mounted marker light xed on a driver support is simple to
install by burying its protected driver support in the ground. The top of this LED marker
light’s shaft is exible, and the head can be accurately swivelLED towards the object
to be lit. Uses 3 powerful LEDs to illuminate driveways, pathways, stairs, landscaped
gardens, trees, plants... It has been designed in particular for landscape architects and
blends perfectly into any green spaces.
TULIPA
230VAC
POWER 3x2.5W
SUPPLY 230VAC
POWER
SUPPLY
Included
WIRING Parallel
AVERAGE LIFE OF THE
LED
60 000 hours
Certicated L90 B10
COLOUR EMISSION 2700°K - 3000°K
4000°K - 6000°K
BEAM 6°-25°-40°-115°
INITIAL OUTFLOW 634lm at 3000k
Electrical features
TECHNICAL SHEMATICS
SIZE 3000x49mm
WEIGHT 1.9kg
MATERIAL Brass - Bronze
OPERATING
TEMPERATURE
- 20°c ~+ 60°
PROTECTION RAITING IP68
RESISTANCE INDEX IK10
APPLICANCE CLASS CLASS II
WALKOVER FIXTURE NO
DRIVE-OVER FIXTURE NO
Mechanical characteristics
INSTALLATION SHEMATICS
Characteristics
lighting techniques
General characreristics
POWER SUPPLY
CABLES
Supply wire 2x1
mm2 en IP68
PHOTOBIOLOGICAL
SAFETY
Risk group I
ENERGY CLASS A /A+/A++
All data are given for information purposes only. They do not constitute a contractual commitment on our part and are subject
to change at any time.
4949
5252
T° max 55°C
AA+
A++
IP68
NGR
IK10
1,9
IP68
Connecteur
1
4
4
3
IP67
IP68
Connecteur
3
IP67 IP68
3
12
3
Parallel wiring 230VAC
Two people are needed to install the
projector, one person wraps it around
the shaft, while the other holds the
projector head.
Never rewind
a projector
already
installed.
USE A IP68 CONNECTOR
Not submerged

1. Use
Shaft-mounted marker light, fixed on a protected driver support to insert in the
ground. The top of the shaft is flexible, and the head can be swivelled towards the
object to be lit. Fitted with 1 powerful LED, it can illuminate driveways, pathways,
stairs, landscaped gardens, small trees, etc. Specially intended for landscape
gardeners, it will blend perfectly into your outside spaces. Only an IP68 connection
to the electricity network ensures the IP67 degree of the product. Characteristics
Assembly/specific applications available on request.
2. Technical data/Assembly
Shaft mounted projector with 3x2.5W LED, cold white (6000 K), neutral white
(4000 K), warm white (3000 K) rotating 360°. Diffusion of light by rotational
symmetry of 6°- 25°- 40° and 115°. Delivered with 1m submersible cable.
3. Installation/assembly
Please comply with the applicable national safety requirements We disclaim
all responsibility for non-compliant use or assembly. Similarly, we reject any
responsibility for any modifications you may make to the light fittings.
For their use, constant current projectors must always be connected in series
to the corresponding DC power supply (see power packs) (230VAC). Exterior
installation can be carried out on different media. Install the projector directly
in sand, earth, ... We cannot supply universal installation instructions because
ground conditions and the location will vary for each project. The pictograms
show examples of typical installations
Install by simply inserting the terminal directly in the ground using a PT800
earth rod. Use only the factory-connected cables. Please indicate the required
cable length when ordering. In the event of mechanical stress, the cable must be
installed in a protective conduit. The silicone cable must only be connected to the
power supply in a dry environment and, in the event of a direct connection in the
ground, only connection units compatible with a joint sealing compound should
be used. Connect the various conductors to power supplies in accordance with
instructions.
4. Connecting to the power packs/connection matrix
Constant current spotlights must only be connected in series. If applicable,
proceed with connection in series in separate load distribution units, the outside
of which must also be protected against humidity using a sealing compound.
5. General Maintenance Instructions
Do not use detergents which are harmful to metals when cleaning the spotlight.
The use of hydrochloric acid-based detergents on and around any parts of a
stainless steel light fitting is totally forbidden.
Regularly clean the spotlight and its mounting box to avoid any rust deposit.
6. Warranty conditions
The following time limits and provisions of the warranty shall apply from
the date of delivery: - 24 months for Orsteel spotlights. The warranty covers
defects in materials, manufacturing defects and any treatment which is proven
to be attributable to the manufacturer. Any damage resulting from the non-
compliance with this user leaflet or any non-compliant repair is excluded from the
warranty. We disclaim any guarantee where the installation has not been carried
out according to the instructions or where unsuitable bulbs or connection cables
have been used. We reserve the right to make any modification corresponding to
technical advancement.
7. Important Notice
(The warranty becomes void in the event of non-compliance with the following
points)
The absence of damage during transport must be verified before installation.
Any assembling and installation, as well as any electrical work, must be carried
out by qualified personnel.
To avoid any rust deposits, only stainless steel tools should be used.
The cable length for lamps must be chosen to avoid extending it in water or in a
damp environment. Any subsequent claim for this reason will not be accepted.
A mounting distance of 10 cm between each device is strongly recommended to
avoid mutual heating.
Equipment must be connected without current, otherwise surges in the power
supply could damage the LEDS. There must be no primary voltage when changing
LEDs.
When connecting the lamps, please ensure that polarity matches! A polarity error
may damage the LED module.
The customer is advised to install protection against any over voltage compliant
with standards DIN VDE 0100-443, DIN VDE 0100-534 and En 62305.
Please observe the measures against electrostatic discharge during all work on
the spotlights, equipment and LEDs.
INSTALLATION GUIDE