OR STEEL light MINILIGHT 230VAC User manual

TECHNICAL MANUAL
The Minilight mounted floodlight is suitable for landscaped zones and architectural
lighting. With a discreet, contemporary design, it can be used for many lighting
applications and on any exterior surface.
Perfect for stunning landscape lighting, it has an IP68 watertight cable.
The adaptability of Minilight will satisfy all your contemporary LED lighting
requirements.
MINILIGHT
230VAC
POWER 7.5W
SUPPLY 230VAC
POWER
SUPPLY
Included
WIRING Parallel
Electrical features
TECHNICAL SHEMATICS
SIZE Ø92x95mm
WEIGHT 0.48kg
MATERIAL Solid aluminium
OPERATING
TEMPERATURE
- 20°c ~+ 40°
PROTECTION RAITING IP68
RESISTANCE INDEX IK08
APPLICANCE CLASS CLASS II
WALKOVER FIXTURE NO
DRIVE-OVER FIXTURE NO
Mechanical characteristics
INSTALLATION SHEMATICS
General characreristics
POWER SUPPLY
CABLES
Supply wire 2x1 mm²
in IP68
PHOTOBIOLOGICAL
SAFETY
Risk group I
ENERGY CLASS A /A+/A++
All data are given for information purposes only. They do not constitute a contractual commitment on our part and are subject
to change at any time.
T° max 55°C
AA+
A++
NGR
IP68
0,48
9595
9292
6262
6060
3636
AVERAGE LIFE OF THE
LED
60 000 hours
Certicated L90 B10
COLOUR EMISSION 2700K - 3000K -
4000K - 6000K
RED - GREEN
BLUE - AMBER
BEAM 10°-25°-40-115°
INITIAL OUTFLOW 634lm at 3000k
Characteristics
lighting techniques
Parallel wiring 230VAC
IP68
Connecteur
Sous-terre
12
3
Version to be
screw
Version to be planted
USE A IP68 CONNECTOR
Not submerged
IK08

1. Use
Discreet floodlight, for occasional illumination of small architectural details. Only
an IP68 connection to the electricity network ensures the IP68 degree of the
product/specific applications available on request.
2. Technical data
Moving head projector with 3x2,5W LED cold white (6000 K), neutral white
(4000 K), warm white (3000 K), red, green, blue and amber Diffusion of light by
rotational symmetry of 10° 25° 40° and 115° for LEDS, 316L stainless steel gland.
Delivered with 2x1mmSubmersible cable.
3. Installation/assembly
Please comply with the applicable national safety requirements. We disclaim
all responsibility for non-compliant use or assembly. Similarly, we reject any
responsibility for any modifications you may make to the light fittings.
For their use, constant current spotlights must always be connected in parallel
to the corresponding DC power supply (see power packs) (230VAC). Exterior
installation can be carried out on different media. The spotlight can be installed
directly in concrete, paving blocks, plates, wood and using a Pt800 earth rod. We
cannot supply universal installation instructions because ground conditions and
the location will vary for each project.
The pictograms show examples of typical installations.
When mounting on a reinforced bracket, you must remove the screws.
Remove the projector from its support and direct it toward the object to be lit.
Then fix to the bracket using the A4 stainless steel screws provided. Use only
the factory-connected cables. Please indicate the required cable length when
ordering. In the event of mechanical stress, the cable must be installed in a
protective conduit.
The silicone cable must only be connected to the power supply in a dry environment
and, in the event of a direct connection in the ground, only connection units
compatible with a joint sealing compound should be used.
Connect the various conductors to power supplies in accordance with instructions.
4. Connecting to the power packs/connection matrix
Constant voltage headlamps should only be connected in parallel. If necessary,
connect in parallel in separate distribution boxes, the outside of which must also
be protected against humidity using a sealing compound.
5. General Maintenance Instructions
Do not use detergents which are harmful to metals when cleaning the spotlight.
The use of hydrochloric acid-based detergents on and around any parts of a
stainless steel light fitting is totally forbidden.
Regularly clean the spotlight and its mounting box to avoid any rust deposit
Caution: Do not use a high pressure cleaner. Caution: Protect the spotlights from
frost; where appropriate, dismantle or ensure special protection. Any lost screws
must be replaced by stainless steel V4A screws. According to conditions of use
(power, environmental circumstances), it is recommended to change the seals
(on the glass, screw fittings and O-rings) and the cable every 5 to 8 years.
6. Warranty conditions
The following time limits and provisions of the warranty shall apply from
the date of delivery: - 24 months for Orsteel spotlights. The warranty covers
defects in materials, manufacturing defects and any treatment which is proven
to be attributable to the manufacturer. Any damage resulting from the non-
compliance with this user leaflet or any non-compliant repair is excluded from the
warranty. We disclaim any guarantee where the installation has not been carried
out according to the instructions or where unsuitable bulbs or connection cables
have been used. We reserve the right to make any modification corresponding to
technical advancement.
7. Important Notice
(The warranty becomes void in the event of non-compliance with the following
points)
The absence of damage during transport must be verified before installation.
Any assembling and installation, as well as any electrical work, must be carried
out by qualified personnel.
To avoid any rust deposits, only stainless steel tools should be used.
The cable length for lamps must be chosen to avoid extending it in water or in a
damp environment. Any subsequent claim for this reason will not be accepted.
A mounting distance of 10 cm between each device is strongly recommended to
avoid mutual heating.
Equipment must be connected without current, otherwise surges in the power
supply could damage the LEDS. There must be no primary voltage when changing
LEDs.
When connecting the lamps, please ensure that polarity matches! A polarity error
may damage the LED module.
The customer is advised to install protection against any over voltage compliant
with standards DIN VDE 0100-443, DIN VDE 0100-534 and En 62305.
INSTALLATION GUIDE