Oracle FRONTDOOR OFD-614 User manual

Model OFD-614
5/4/2006
Patents Pending
NOTE:
8.0
- 1 -
TABLE OF CONTENTS
- 12 -
Thank you for purchasing the Oracle
FrontDoor Unit. This product has been
designed and manufactured in the USA,
utilizing the highest quality standards
available.
Made With Pride In the USA.
A manufacturer’s full One Year Warranty covers this product.
No Wiring or Trenching
Required
One year limited WARRANTY
International Electronics Inc. (IEI) warrants this product to be free of defects in materials and
workmanship, for one year. For a period of ONE YEAR following purchase, IEI will repair or
replace the product free of charge, including parts, labor, return shipping to you, and handling.
After the initial one year of operation, the limited lifetime warranty will cover parts, labor, and
return shipping to you, with a minimal handling charge specific to the product, as listed below:
FrontDoor Wireless Intercom: $40.00
If you have installation or operation questions or are in need of warranty service, please
contact our Product Support department by email at [e-mail] or call 360-254-
1564 Tuesday-Friday 7-5 Pacific Time. If the issue is not resolvable, a manufacturer’s
warranty repair order may be issued. To have the product(s) sent for warranty service. A
Return Authorization number will be issued for warranty service, which must be put on the
outside of the package, to be received and handled properly. Packages for warranty service
may be sent to the following address. Packages with no RA# may not be accepted.
IEI
5913C NE 127th AVE, Suite 800
Vancouver, WA 98682
Please include a note describing the problem that you are having and a copy of your original
sales receipt (within the first year). If the warranty service is outside the first year, please
include a check made out to IEI, based on the list of handling fees, shown above. Please note
that you may need to send multiple units for warranty service, testing, and upgrading, though
only the applicable fee for handling the failed unit(s) will be charged.
Please allow 2-4 weeks for service and return shipping. If an EXPEDITED repair/replacement is
requested, a 100% surcharge applies. In this case, please write EXPEDITED after the RA
number. IEI will attempt to return expedited repair orders within one week, except during
holidays.
All repairs or replacements are at the discretion of the Manufacturer. This warranty excludes
items that have been abused, altered, incorrectly installed, or repaired by an unauthorized
person. Changes or modifications not expressly approved by the Manufacturer could void the
user’s authority to operate the equipment. The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modifications to this equipment. Such modifications
could void the user’s authority to operate the equipment. This warranty is limited to the product
only. No consequential damages are covered.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
International Electronics, Inc.
FCC ID: JLFODI1
IC:
Country Of Origin: USA
• Easy to Install
• Totally wireless
• Fully Compatible with other Oracle Intercom units
• Weather Resistant Design
• Doorbell tones for Front Door and Back Door
• Unlimited number of units can operate on a property,
without interfering with other Intercom Networks
• Up to 5 Year battery life
• Penetrates buildings with ease
• Range up to 1000 feet
• Auto channel and frequency selection
• Crystal Clear, digitally secure connection
• 900 MHz Digital Radio Technology
• One year limited warranty
Oracle
(tm)
FrontDoor
™
Wireless
Doorbell and
Intercom
This product is compatible with Oracle Portable Intercom (OPI)
model 605-
5 or later and/or Oracle Telephone Interface Unit
(OTIU).

Model OFD-614
5/4/2006
Patents Pending
5.1
ADJUSTING THE SPEAKER VOLUME
- 2 - - 11 -
GENERAL INFORMATION
(Use this template as a guide for mounting screw placement)
Preface
General Information………………………………………….………….….….3
Parts Supplied……………………………………………………………….....3
.
Section 1 – Installation
1.1 Installing the Oracle FrontDoor (OFD)…………………….……...4
A.
Installing the OFD with screws……………...……………..…4
B. Installing the OFD with mounting tape………...………..…...4
1.2
Installing the Batteries………………………………………...…….5
Section 2 – Activation
2.1
Activating an Intercom Network……………………..……………..5
A. Activating the OFD with an Oracle Portable (OPI)………….5
B. Activating the OFD with a Flush Mount (RIFM)……..…..….5
C. Activating the OFD with a Telephone Interface (OTIU)……6
2.2
Activating into an Existing Network……………….…………….....6
A.
Activating an OFD to the Main Intercom Unit…………..…..6
B.
Activating Intercom Units back into the network………..….6
2.3 Multi-OFD Mode……………………………………….………….…7
A.
Activating an OFD with an OFD………………………..…….7
B.
Activating an OFD with a Gate Access Panel………..…….8
C.
Activating an OFD with a Repeater……………………..…...8
Section 3 – Assembly
Assembling the Intercom…………………………………………………..…9
Section 4 – Use
Using the Intercom………………………………………………..…………..9
Section 5 – Adjusting Volume
5.1 Adjusting the Speaker Volume………………………...………..10
5.2 Adjusting Microphone Sensitivity…………………………....….10
Section 6 – Alternate Doorbell Chimes
Alternating Chimes for FrontDoor vs. BackDoor…………………….…..10
Section 7 – Frequently Asked Questions
Troubleshooting and FAQ’s……………………………..………………....10
Section 8 – Mounting Template
Mounting Template…………………………………………………….…...11
MOUNTING TEMPL TE
NOTE: The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications to this equipment. Changes or modifications not
expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.

Model OFD-614
5/4/2006
Patents Pending

5.2
1.1
C.
Nothing Happens. The Intercom Does Not Function
The Intercom is Not Getting the Expected Transmission Range
There is a Double Beep Every Ten Minutes
ADJUSTING MICROPHONE SENSITIVITY
6.0 ALTERNATE CHIMES FOR FRONTDOOR VS. BACKDOOR
7.0 TROUBLESHOOTING AND FREQUENTLY ASKED QUESTIONS
How do I Clear an Intercom's Memory
PARTS SUPPLIED WITH OFD SINGLE UNIT
PARTS SUPPLIED WITH OFD/OTIU KIT
PARTS SUPPLIED WITH OFD/OPI KIT
- 3 -
ACTIVATING THE OFD WITH A REPEATER - CON'T
- 10 -
INSTALLING THE OFD
By switching dipswitch #4 UP (away from the circuit board), you can set the Indoor/Outdoor
Intercom’s volume to be louder.
To increase the Outdoor Intercom’s microphone sensitivity, switch dipswitch #3 UP (away
from the circuit board).
The FrontDoor can be set to ring the inside Intercom units with two alternate chime patterns,
to identify which unit is signaling. Switch dipswitch #2 UP (away from the circuit board) to set
a FrontDoor unit to the alternate chime tone.
Make sure that the Intercom has fresh batteries in it. W hen you press the CALL
button, you should hear a tone. If the units have power but do not communicate,
they may need to form a network. Press the LEARN button on each unit that needs
to form a network
and they will beep in response. You may need to clear their
memory and re-teach them (see How do I Clear the Intercom’s Memory, below).
Trees, metal, electrical wiring or other electrical devices directly between units can
limit the range, as can having it mounted on a tree, masonry, or metal surface.
NOTE: STUCCO WALLS
When used in a dwelling with stucco or cement walls, the RF range can
be
reduced greatly. Place the repeater close to the house to mitigate this problem.
The intercom is indicating that the batteries are low and need to be replaced.
(Only when used in passive mode. In active mode there is no need to erase this devices memory)
Hold the LEARN button down for 20 seconds. A tone will indicate that the unit has
cleared its memory and you can re-
teach it to a new intercom. If an intercom
signals, while the buttons are depressed, the procedure will have to be repeated.
1 - Oracle FrontDoor Unit (OFD)
2 – Black #8 X ¾ Assembly Screws
4 – Silver #4 X ¾ Mounting Screws
1 – Piece of 3M High Strength Mounting Tape
The Oracle FrontDoor (OFD) is designed for use as a Wireless Doorbell
and Intercom for residential, as well as commercial applications. It is
designed to tolerate severe outdoor conditions of -40 to +85 C, as well as
high humidity and condensation. Since this intercom system requires no
connection to wall power, it is perfect for remote locations.
The Oracle FrontDoor (OFD) features an amazing 1000’ range, and
allows multiple simultaneous conversations, using a 900 MHz secure
digital radio link.
Compatible with the Oracle Portable Intercom (OPI) and Oracle Flush
Mount Intercom (RIFM), your intercoms form an exclusive network, and
respond only to other intercoms in your network (patent pending).
When used with Oracle Telephone Interface Unit (OTIU), the Oracle
FrontDoor (OFD) will ring your telephones and allow you to speak with the
visitor. No wiring of any kind is required. Simply plug into any phone jack
and receive your visitors on the phone. Features Caller ID and much
more.
All of the parts supplied with the OFD plus:
1 - Oracle Telephone Interface Unit (OTIU)
1 – Instructions for Installing the OTIU
1 - Antenna
1 – 18V Power Adapter
1 – Phone Cord
1 – Set of 4 Bumper Feet
All of the parts supplied with the OFD plus:
1 – Oracle Portable Intercom (OPI)
1 – Instructions for Installing the OPI
1 – Set of 4 Bumper Feet
Make sure that the “CALL” button is in easy reach of a visitor. The unit may be mounted with
either the included screws or the included double-sided high strength tape.
NOTE: If the Repeater Units have not been previously activated to
anything within an existing network, please follow the directions found

Model OFD-614
5/4/2006
Patents Pending
A.
B.
Figure 1
1.2
MOUNTING THE OFD WITH SCREWS
MOUNTING THE OFD WITH MOUNTING TAPE
3.0 ASSEMBLING THE INTERCOM
4.0 USING THE INTERCOM
B. ACTIVATING AN OFD WITH A GATE ACCESS PANEL (GAP)
- 9 -- 4 -
INSTALLING THE BATTERIES
Make sure that the “CALL” button is in easy reach of a visitor. The unit may be mounted with
either the included screws or the included double-sided high strength tape.
To mount the FrontDoor, use the included mounting template (see page 11) as a guide for
screw placement. Tighten the top two screws halfway. Place the back of the Intercom on
the two screws, slide the unit down and tighten. Put the other two screws in t
he bottom
holes and tighten (see Figure 1).
Note: Do not assemble the front of the unit until it has been activated.
To mount the Intercom on a metal, glass, or other smooth surface where you wouldn’t want
to use screws, use the double-sided mounting tape.
Note: For best results, clean both surfaces that the double-
sided mounting tape will be in
contact with, using the included alcohol wipe.
Peel the protective paper off of the mounting tape and firmly press it onto the back of the
Intercom (see Figure 1). Press firmly on the back of the tape; to push out any trapped air
bubbles. When ready to do so, peel the red prot
ective paper from the mounting tape and
firmly press the intercom on to the surface that you wish to mount it on.
Note: Do not assemble the front of the unit until it has been activated.
Put the two halves of the Intercom body together. Place the two black screws in the
top and bottom holes on the front of the Intercom and tighten. The Intercom is ready
to use.
To talk, hold down the “CALL” button. All intercom units in your network will receive
the signal. When somebody responds by holding down the “CALL” button on a
different intercom unit, a secure channel is created and other units will not hear the
signal, making your conversation secure.
NOTE: If the Repeater Units have not been previously activated to
anything within an existing network, please follow the directions found
in the Oracle Wire-free Repeater product manual.
Place four AA Alkaline batteries in the battery pack. The batteries should last one
year with average use.
Note:
If used in location that will be below
-
10
°
C
(20
°
F) Lithium batteries are

Model OFD-614
5/4/2006
Patents Pending
2.1
A.
C.
2.1
C.
ACTIVATING THE OFD WITH A REPEATER
(WITHIN AN EXISTING NETWORK)
ACTIVATING THE OFD WITH AN ORACLE PORTABLE
Note: Both steps 1 & 2 must occur within 15 seconds of each other.
B. ACTIVATING THE OFD WITH A FLUSH MOUNT
ACTIVATING AN INTERCOM NETWORK
Note: Both steps 1 & 2 must occur within 15 seconds of each other.
ACTIVATING AN INTERCOM NETWORK - CON'T
Note: Both steps 1 & 2 must occur within 15 seconds of each other.
- 8 - - 5 -
B. ACTIVATING ADDITIONAL INTERCOM UNITS BACK INTO THE NETWORK
Note: Both steps 1 & 2 must occur within 15 seconds of each other.ACTIVATING THE OFD WITH AN OTIU
To set a FrontDoor unit to Passive Mode, switch dipswitch #1 UP (away from the circuit
board).
Note:
Any Intercoms that had been taught to this unit will have to have their memory cleared
and be re-taught to the Active Unit in the network as if they were newly installed.
Note: Both steps 1 & 2 must occur within 20 seconds of each other.
1.
To activate the Passive FrontDoor, press the LEARN button inside the
FrontDoor unit for a second (until you hear a beep) and release it.
2. Enter the Master PIN number on the GAP:
For example:
Then enter:
After the “BEEP” press “CALL”.
3. You will hear a tone indicating a successful activation.
4. Proceed to Section 3
1234
0 5
1.
To activate the Passive FrontDoor, press the LEARN button inside the FrontDoor
unit for a second (until you hear a beep) and release it.
2.
Press the LEARN button on ONE of the Repeater Units. The LED by the LEARN
button will light up for several seconds
and then will go out, indicating a successful
activation.
3. Proceed to Section 3
(See next page for an example of an existing network with an OFD and Repeater).
1.
Press and release the LEARN button on an Oracle Portable Intercom
(OPI).
2. Press the LEARN button inside the FrontDoor unit for a second (until
you hear a beep) and release. The OPI will sound a tone indicating a
successful activation.
3. Proceed to Section 3
1.
On a Flush Mount Intercom, hold down both buttons for 3 seconds,
until the channel lights start flashing quickly.
2.
Press the LEARN button inside the FrontDoor unit for a second (until
you hear a beep) and release. The Flush Mount will sound a tone
indicating a successful activation.
3. Proceed to Section 3
Note: If used in location that will be below -10°
C (20° F) Lithium batteries are
recommended.
The FrontDoor must be taught to an intercom to form an intercom network, or must be
taught into an existing network (See “Activating into an Existing Intercom Network”).
The FrontDoor is fully compatible with other Oracle System Intercoms.
1. Press and release the LEARN button on an un-
activated Oracle Intercom
(On a Flush Mount Intercom hold down both buttons for 3 seconds, until the
channel lights start flashing quickly).

Model OFD-614
5/4/2006
Patents Pending
2.3
A.
A. ACTIVATING THE OFD TO THE MAIN INTERCOM UNIT
- 6 -
MULTI-OFD MODE
ACTIVATING AN OFD WITH AN OFD
- 7 -
2.2 ACTIVATING INTO AN EXISTING INTERCOM NETWORK
Note: If the existing network contains a GAP, MiniGAP, or another FrontDoor see “Multi-
FD
Mode”.
To activate a FrontDoor into an existing intercom network, the memory on each of the
Intercoms to be used, needs to be cleared.
Note: To clear the memory on
an Oracle Intercom, hold down the learn button for up to 20
seconds until a tone is heard.
Note:
To clear the memory on a Flush Mount Intercom, hold down both buttons of the
Intercom for up to 20 seconds until a tone is heard.
Note: Both steps 1 & 2 must occur within 20 seconds of each other
1.
Press and release the LEARN button on an Oracle Intercom (On a Flush Mount
Intercom hold down both buttons for 3 seconds, until the channel lights start flashing
quickly).
2. Press and release the LEARN button inside the FrontDoor unit.
Note:
Activate all other Intercoms to this Intercom, NOT to the FrontDoor. (See example
below and Step B on next page.)
Note: Both steps 1 & 2 must occur within 20 seconds of each other.
1. Using the phone that is connected to the OTIU, once you hear a dial tone press:
Hang up and the LEARN light will flash for up to 15 seconds. If it does not and you
hear an error tone, check the OTIU manual.
2. On the FrontDoor, press and hold down the learn button for 1 second, to put it into
learn mode.
3. The OTIU will ring the telephone and a Caller ID will display "Unit Learned".
4. Proceed to Section 3
*
*
0 7 "BEEP"
Step A
Step B
Step B
To set a FrontDoor unit to Passive Mode, switch dipswitch #1 UP (away from the
circuit board).
Note:
Any Intercoms that had been taught to this unit will have to have their memory
cleared and be re-taught to the Active Unit in the network as if they we
re newly
installed.
Note: Both steps 1 & 2 must occur within 20 seconds of each other.
1.
To activate the Passive FrontDoor, press the LEARN button inside the
FrontDoor unit for a second (until you hear a beep) and release it.
2. Press the LEARN button i
nside the primary FrontDoor unit for a second
(until you hear a beep) and release it.
3. You will hear a tone indicating a successful activation.
4. Proceed to Section 3
channel lights start flashing quickly).
2. Press and release the LEARN button on the activated Oracle Inter
com or
Flush Mount Unit.
3. Proceed to Section 3
An Oracle FrontDoor (OFD) unit is an ‘Active’ unit that takes control of the Intercom
Network. If you wish to have a second (or multiple) Oracle Frontdoor unit in the
network, or if using the Frontdoor with an Oracle Gate Access Panel, or MiniGAP,
then it
will have to be placed in Passive mode. The Passive FrontDoor will become an
accessory to the Primary FrontDoor or Gate Access Panel.

Model OFD-614
5/4/2006
Patents Pending

Model OFD-614
5/4/2006
Patents Pending

Model OFD-614
5/4/2006
Patents Pending

Model OFD-614
5/4/2006
Patents Pending