Orbis ATC-820 User manual

USB - RS-485 Interface Converter
User’s Manual
Introduction
The ATC-820 module is a cost-effective way to convert
RS485 industrial buses to a USB interface. When connected
to a PC USB port the ATC-820 module is automatically
detected and is installed as a native COM port which is
compatible with any existing serial communication application.
Multiple modules can be installed when using USB hubs thus
allowing a hassle-free configuration of a multi serial system
without any IRQ or DMA configuration. They have 600W
protect between the USB port and RS485 protects the PC
from spykes or possible misconnections in the communication
bus.
Features
The ATC-820 converter can be configured for RS485 two-
wire (Half Duplex) networks. When operating in two-wire
RS485 the data transfer control is automatically done by the
converter. Two independent and RS485 networks can be
supported by one ATC-820 module thus duplicating the
possible number of remote devices.
Computer interface: USB V1.1 2.0 Plug and Play.
Operational system virtual serial port driver.
Supports Windows 98/ME/XP/2000/CE, MAC & Linux
2.4.20 or superior.
Field Interfaces: RS-485 Half Duplex (dual buses).
Automatic flow control for RS485 Half Duplex.
Transmission rate: from 300 bps to 1Mbps.
Maximum RS-485 cable length : 1200 m
Maximum number of devices in the RS485 network: Half
Duplex to 32 devices.
Power: from the USB port.
Consumption: <100 mA.
RS-485 bus protection: 600W.
USB connection: Mini-B connector. 100cm cable with the
module.
RS-485 connector: DB9M or RJ-45 type accepting
ABS enclosure: 67 x 30 x 24 mm (not include cable).
Operating environment: 0 to 70°C, 10 to 90% relative
humidity, non-condensing.
Wiring configuration
The RS-485 termination of the Interface is implemented as a
DB9 plug. The pin assignments for the connector can be
found in the following table as well as on a sticker applied to
the unit.
RS-485 Pinout at DB9 Male
PIN# RS-485
1 485 -
2 485 +
LED indication
Red LED - Data Sending From USB port to RS-485
Serial Port side Green LED - Data Receiving from RS-485
Serial port side to USB port.
Wiring examples
RS-485 2- Wire application
Driver Installation
Follow the steps below to install driver of USB-High Speed
Serial Converter:
1. Power on your computer and make sure that the USB
port is enabled and working properly.
2. Plug in the USB-High Speed Serial Converter into the
USB port and run the Add New Hardware Wizard to
assist you in setting up the new device. Click Next to
continue.
3. Insert the USB-HS Serial Converter software driver into
the CD-ROM drive and click Next to continue. For
Windows 98, click Search for the best driver for your
device and click to search driver from the floppy drive
D:\DRIVER\Win98&Win2000.
4. Windows will detect the driver (FTDIBUS.INF) and shows
the USB HS SERIAL CONVERTER. Click Next to
continue installation.
5. Click Next to continue and let Windows copy the needed
files to your hard disk.
6. When Windows finished installing the software required
for the new USB to Serial Cable, click Finish.
Setting Up the RS232 Serial Device
Follow the steps below to connect your RS232 Serial Device
(ie: Modem) to the USB port of your PC:
1. Turn off your Modem. Plug the DB 9 (or DB 25) connector
of the USB-HS Serial Converter into your Modem. Connect
the other end of the USB-HS Serial Converter to an USB type
A to type B cable. Turn on the Modem afterwards.

2. Turn on your computer and plug in the USB connector of
the USB-HS Serial Converter into the USB port.
3. If you have already installed a Modem device before, click
Start, Settings, and Modems. Open Modems Properties,
select the Modem, and click Properties. In General tab,
please change the Port value to USB Serial Port (COM3).
4. After finishing these processes, you can use USB to Serial
Bridge Cable to connect RS232 Serial 56K FAX Modem and
execute the Dial-up function to connect Internet, and send the
FAX with the FAX software (ie: Microsoft FAX) properly.
Uninstalling the Driver Program
If you want to remove the USB-HS Serial Converter driver
program, you can uninstall it by following the steps below:
1. Unplug the USB-HS Serial Converter from your PC.
2. Run the D:\Driver\Win98&win2000\FTDIUNIN.EXE
program from the software CD-ROM, Click finish then
reboot the PC.
Disclaimer
Information in this document is subject to change without
notice. The manufacturer does not make any representations
or warranties (implied or otherwise) regarding the accuracy
and completeness of this document and shall in no event be
liable for any loss of profit or any other commercial damage,
including but not limited to special, incidental, consequential,
or other damages. No part of this document may be
reproduced or transmitted in any form by any means,
electronic or mechanical, including photocopying, recording or
information recording and retrieval systems without the
express written permission of the manufacturer.
All brand names and product names used in this document
are trademarks, or registered trademarks of their respective
holders.
A016.70.56505
ORBIS TECNOLOGIA ELECTRICA, S.A.
Lérida, 61 E-28020 MADRID
Teléfono: [phone]; Fax: [phone]
E-mail: info@ orbis.es
http://www.orbis.es