Oregon Scientific BAR338PA User manual

1
GB
RF Projection Barometer
With Remote Thermo Sensor
Model No.:BAR338PA
User’s Manual
INTRODUCTION
Congratulations on your purchasing the BAR338PA RF Projection
Barometer.
TheBAR338PAisamultifunctionalradiofrequency(RF)controlled
projection calendar clock that automatically synchronizes current
timeanddatewiththeRFsignal broadcastbytheUSAtomicClock,
one of the world's most accurate timekeepers.
The BAR338PA is very easy to use. No wire installation is required
between the main unit and the remote unit.
Other features of BAR338PA include: weather forecast display,
indoor and remote temperature display and daily alarm function.
MAIN UNIT CONTROLS

2
GB
A3 IN/OUT BUTTON
Changes between indoor and outdoor temperature
A4 CLOCK BUTTON
Alternates between the time seconds display and the day-
of-the-week display; also enables the clock setting mode
A5 ALARMBUTTON
Displays the alarm set time or activates the alarm function
A6 UP [ ] AND DOWN [ ] BUTTONS
Increases or decreases the value of a setting
A7 °C/°F BUTTON
Selects between degrees Centigrade (°C) and Fahrenheit
(°F)
A8 RESET BUTTON
Clears the user selected settings and causes the settings of
the main display unit to return to the factory default
settings
A9 ZONE BUTTON
Sequencethroughthe4UStime-zonesofPacific,Mountain,
Central and Eastern
PROJECTOR CONTROLS
A10 IMAGE ROTATION KNOB
Rotates the projected time image 90 degree in clockwise or
counter-clockwise direction
A11 FOCUS KNOB
Adjusts the focus of the projected time image
A1 SNOOZE/LIGHT BUTTON
Enables the snooze alarm feature when the alarm is
sounding; also activates the backlight feature for five
seconds
A2 MEMORYBUTTON
Sequencethroughtemperaturedisplayselectionsofcurrent,
maximum and minimum temperatures

3
GB
A12 180°ROTATION BUTTON
Flips the projected time image upside-down
A13 PROJECTION ON SLIDE SWITCH
Activates continuous projected time image function when
used with the included AC power adapter
MAIN UNIT INDICATORS
A14 WEATHER FORCAST ICONS
Graphically displays general weather forecast 12-24 hours
in the future
A15 ALARM ON INDICATOR
Appears when the alarm is active
A16 IN/OUT INDICATOR
Indicates outdoor or indoor temperature
A17 ALARM TIME INDICATOR
Appears when the alarm time is displayed
A18 RADIO RECEPTION SIGNAL
Identifies the strength of signal received from the US
Atomic Clock
A19 BATTERY-LOW INDICATOR
When displayed indicates that batteries are low and need to
be replaced
A20 M/D INDICATOR
Indicates month-day (MD) calendar display
REMOTE UNIT CONTROLS
B1 LED INDICATOR
Flashes when the remote unit transmits a reading
B2 RESET BUTTON
Clears the user selected settings and causes the settings of
the remote sensor to return to the factory default settings

4
GB
MAIN UNIT
HOW TO USE THE PROJECTOR
The BAR338PA includes a projection function that projects the
current time and remote sensor temperature onto a wall, ceiling or
other flat surface.
Toproject thetime-temperature ontoa flatsurface:
Inadarkenedroom,press[SNOOZE/LIGHT ],theprojectionwill
activate for approximately 5 seconds.
This unit has several features to enhance the clarity of the projected
image.
HINTS FOR BEST OPERATION
• Insert batteries in the remote unit before doing so for the main
unit.
• Position the main and remote unit within the transmission
range (20 to 30 meters; 65.5 - 100 feet).
• Position the remote unit away from direct sunlight, rain or
snow.
• After battery installation, the main unit will search for signal
from the remote unit. Upon successful receipt of signal, the
remote temperature reading received will be displayed on the
main unit. Should the signal reception between the main unit
and the remote sensor be unsuccessful, shorten the distance
between them and/or reposition the main unit and/or the sensor
so they are in a more direct line of sight to one another.
BATTERY INSTALLATION
1. Remove the battery compartment door.
2. Insert two AA-sized batteries (included) for the remote unit or
four AA-sized batteries (included) for the main unit. Batteries
are to be inserted with polarities in the direction shown in the
diagram on page 3 for the remote sensor unit and page 4 for the
main display unit.
3. Press [RESET].
4. Replace the battery compartment door.

5
GB
ProjectorFeatures
Feature Effect Instructions
Adjustable Rotates180° to cast Adjust by pivoting forwards
Projector image onto any wall or backwards the projector,
so that the projection lens
is pointed in the appropriate
direction
FOCUS Focusesimage Rotate knob forwards or
Knob (A11) backwards until the image
clarityisoptimized
[ ] Rotatesimageona Turns an image to maintain
IMAGE given surface to an upright position
ROTATION maintain an upright
knob(A10) position
180° Horizontally flips Flipsan image to maintain
ROTATION an image on a given an upright position
button (A12) surface to maintain
an upright position
HOW TO USE THE PROJECTOR
POWER ADAPTER
Your BAR338PAcomeswithanACpoweradapter. Forcontinuous
projection the AC power adapter must be used. To install the
adapter:
1. Unscrew the cover at the bottom of the stand.
2. Plug the adapter into the adapter socket.
3. Connect the power adapter to a wall socket.
4. Slide[PROJECTIONON]toON.
Toturnofftheprojector, slidethe[PROJECTIONON]back.Note
that this switch can only be used with the power adapter connected.
For momentarily projection, use [SNOOZE/LIGHT].
HOW TO USE THE BACKLIGHT
Press the [SNOOZE/LIGHT]buttononce. Thebacklight will light
up on the LCD Display and around the key panel for five seconds.
Projection will also be on for five seconds.
DISPLAY MODES
In normal display mode, the current time, including seconds, will
bedisplayed.Todisplayweekday,press [CLOCK]once.Toswitch
back to normal time display, press [CLOCK] once.

6
GB
To display the daily alarm time, press [ALARM] once when the
date is displayed. To display the date, press [CLOCK] once when
alarm time is displayed.
The temperature and weather forecast will be shown in all display
modes.
ABOUT RADIO RECEPTION
The BAR338PA is designed to synchronize current time and date
information via radio frequency signals from the US Atomic
Clock, one of the world's most accurate timekeepers.
After batteries are installed in the main unit, press ZONE to select
the appropriate US time zone of Pacific, Mountain, Central or
Eastern. Note that the appropriate time zone needs to be selected
each time if the BAR338PA is moved from one time zone to
another.
When the unit is receiving radio signal, the reception icon will start
to blink. The reception icon will show either strong, weak or no
signal depending on the strength of the radio signal. A complete
reception generally takes about two to 10 minutes.
When the reception is completed the reception icon will stop
blinking. The reception icon will show " " for no reception or
" " for successful reception.
For best signal reception, position the BAR338PA away from PC's,
radios, TV's, microwave ovens and other appliances that emit or
receiveradiofrequencysignals. ShouldtheBAR338PAbe new and
just out of the box, allow up to 72 hours for the unit to receive the
initial signal reception. To facilitate signal reception, poisitioning
on a windowsill is recommended.
HOW TO SELECT THE TIME-ZONE
After batteries are installed in the main display unit, press [ZONE]
toselect the appropriateUS time zoneof Pacific,Mountain, Central
or Eastern. Note that the appropriate time zone needs to be selected
eachtimeiftheBAR338PAismovedfromonetimezonetoanother.
Reception
complete No reception, or Successful reception
manually adjusted
Receiving
radio
signal No signal Weak signal Strong signal

7
GB
The [ZONE] button is located inside the battery compartment.
Press [ZONE] button to select among the 4 US time-zones: Pacific,
Mountains, Central or Eastern.
HOW TO MANUALLY SET THE
CALENDAR CLOCK
When travelling outside of the US Atomic Clock signal reception
range, the BAR338PA can be manually set to operate as a quartz
clock. Note that setting the clock manually will disable the signal
reception and synchronization function. To set the clock manually:
1. Press and hold [CLOCK] for two seconds.
2. Enter the hour using the [ ] or[ ] buttons. Hold down either
button to rapidly increase or decrease the value.
3. Press[CLOCK].
4. Enter the minute using the [ ] or [ ] buttons.
5. Press[CLOCK].
6. Follow the same procedure to set the year, month, day and
display language. For the display language, you can choose
English, French or Spanish.
HOW TO SET THE ALARM
1. Press and hold [ALARM] for two seconds.
2. Enter the hour using the [ ] or [ ] buttons.
3. Press[ALARM].
4. Enter the minutes using the [ ] or [ ] buttons.
5. Press[ALARM].
The alarm is automatically activated after the setting procedure. To
deactivate it, press [ALARM] to turn off the [ ] indicator when
the alarm time is displayed.
ALARM AND SNOOZE FUNCTION
Whenthealarmis activated, itwillgooffat thesettime.Thedisplay
will light up for five seconds and the [ ] icon will flash.
The crescendo function allows the alarm to start off gently and with
its intensity in four steps. Without interruption, the alarm will
sound for a minute.
To stop the alarm, press [ALARM]. If the [SNOOZE/LIGHT]
button is pressed, the SNOOZE function will be triggered. The
alarm will stop for eight minutes before going off again.
INDOOR AND OUTDOOR
TEMPERATURES
Press [IN/OUT] to toggle between indoor temperature and outdoor
temperature.
Press [°C/°F] to display the temperature in Centigrade °C or
Fahrenheit °F.

8
GB
MAXIMUM AND MINIMUM
TEMPERATURES
Press [IN/OUT] to select indoor or outdoor temperature display.
Then press [MEMORY] repeatedly to scroll through current
maximum and minimum temperatures recorded.
Toclearthememory,selectindoororoutdoortemperaturedisplay.
Then press and hold [MEMORY] for two seconds to clear the
memory for the selected display.
INTERRUPTED SIGNALS
If without obvious reasons the display for the outdoor temperature
becomes blank, press and hold [IN/OUT] for two seconds to
enforce an immediate signal search. If that fails, check if the
remote unit is still in place. Make sure the transmission is within
rangeandpathisclearofobstaclesandinterference.Themaximum
transmission range between the remote sensor and the main
display unit is 90 feet (28 meters).
TRANSMISSION COLLISION
Signals from household devices, such as doorbells, home security
systems and entry controls, may interfere with those of this product
and cause temporarily reception failure. This is normal and does
not affect the general performance of the product. The transmission
and reception of temperature readings will resume once the
interference recedes.
WEATHER FORECAST
The unit is capable of detecting barometric pressure changes, and
basing on the data collected, can provide a general weather forecast
for the next 12 to 24 hours. The effective range is 30 to 50 km (18.6
- 31 miles).
sunny partlycloudy cloudy rainy snow
NOTE:
1. The accuracy of a general pressure-based weather forecast is
about 70 to 75%, and therefore, cannot be held responsible for
any inconveniences so caused by an inaccurate forecast.
2. The weather forecast is meant for the next 12 to 24 hours. It may
not necessarily reflect the current situation.
3. The "Sunny" icon, when appears at nighttime, implies clear
weather.
4. When temperature goes equal or below 3OC (+37.4 OF), the
snow icon will display instead of the rainy icon.

9
GB
LOW BATTERY WARNING
When it is time to replace batteries, the low-battery indicator will
appear. Replace the batteries for the main unit when the indicator
appears on the clock window. Do the same for the remote unit when
the indicator appears below the OUT icon.
CAUTION: Batteries contain dangerous chemicals and may leak,
explode or otherwise cause injury and damage if not hadled
properly. Do not mix old batteries with new as this may result in
leakage. Only insert batteries with the polarities in the directions
as shown in this manual. Always dispose of batteries properly.
THE RESET BUTTON
The [RESET] button is used to enhance synchronization of signals
afterbatteryreplacement. NotethatwhenRESETispressedalluser-
selected settings will be cleared and the unit will return to its
factory set default settings. Use a blunt stylus to hold down the
button.
MAINTENANCE
When handled properly, this unit is engineered to give you years
of satisfactory service. Here are a few product care instructions:
1. Do not immerse the unit in water. If the unit comes in contact
with water, dry it immediately with a soft lint-free cloth.
2. Do not clean the unit with abrasive or corrosive materials.
Abrasive cleaning agents may scratch the plastic parts and
corrode the electronic circuit.
3. Do not subject the unit to excessive: force, shock, dust,
temperature, or humidity. Such treatment may result in
malfunction, a shorter electronic life span, damaged batteries, or
distorted parts.
4. Do not tamper with the unit’s internal components. Doing so
will terminate the unit’s warranty and may cause damage. The
unit contains no user-serviceable parts.
5. Only use new batteries as specified in this instruction manual.
Do not mix new and old batteries as the old batteries may leak.
6. Read this instruction manual thoroughly before operating the
unit.
SPECIFICATIONS
Temperature Measurement
Mainunit
Operating range : 23.0°F to 122.0°F
(-5.0°C to +50.0°C)
Temperature resolution : 0.1°F (0.1°C)
Remoteunit
Operating range : -20.0°C to +60.0°C
(-4.0°F to 140.0°F)
Temperature resolution : 0.1°F (0.1°C)
RF Transmission Frequency : 433MHz

10
GB
Maximum Transmission : 90 feets (28 meters)
Range between Main
Display Unit and
Remote Sensor
Temperature sensing cycle : approximately 30 seconds
Radio Controlled Clock
Clock : 12hr format with hh:mm:ss
Calendar : Month / Day
weekday selectable in
3 language (E, F, Sp )
Alarm : 2 minutes crescendo
Snooze : 8 minutes
Power
Main unit : 4 pcs UM-3 or “AA” 1.5V
alkaline battery (included)
AC/DC3Vpoweradapter
(For continuous projection)
(included)
Remote sensing unit : 2 pcs UM-4 or “AA” 1.5V
alkaline battery (included)
Weight
Main unit : 47 gm (11.27 ounces)
Remote sensing unit : 48 gm (3.5 ounces)
Dimension
Main unit : 109 x 158 x 39 mm
4.36" x 6.32" x 1.56"
(H xW x D)
Remote sensing unit : 105 x 70 x 22 mm
4.2" x 2.8" x 0.88"
(HxWxD)
CUSTOMER ASSISTANCE
Should you have questions about this project or require additional
assistance,pleasecontactour24-7-365customerservicedepartment
at 800-853-8883 or via email at [email protected].
WARRANTY
Oregon Scientific, Inc. warrants this product from manufacturing
defects for a period of 90-days from date of retail purchase. Direct
return of defective product to the place of retail purchase. Should
this not be possible, contact our customer service department to
securea ReturnMaterialAuthorization. A RMAisrequired priorto
returning product to Oregon Scientific, Inc. Please keep your
receipt as proof of purchase as the receipt maybe required to
substantiate when purchased. Oregon Scientific, Inc. reserves the
right to replace or repair product at its discretion. This product
contains no user-serviceable parts or components. This warranty
does not cover product subjected to tampering, abuse, misuse or
accidental damage.