ORiNG INJ-101GT++ Series User manual

Quick Installation Guide
Version 1.0
Quick Installation Guide
PRINTED ON RECYCLED PAPER
Q I G 1907-200-N101GT++11-FX010
Introduction
INJ-101GT++ PoE Injector seriesThe is not only an IEEE802.3at compliant
device but also an advanced high power PoE injector. It is intelligent
detection that provided 1-ports 10/100/1000Base-T (X) PoE outputs. The
device does not turn on power until it detects a valid PoE signature from the
PoE devices attached downstream on the Ethernet cable. This protection
against damage to non-PoE compliant equipment which may be connected to
the Ethernet cable. Therefore, only an IEEE 802.3at/802.3af compliant
device can be powered with the PoE Injector. Typically inINJ-101GT++
Gigabit networks the maximum allowable CAT5 cable length is about 100
meters, due to the limitation of the Ethernet standards. The INJ-101GT++
PoE Injector can function with any PoE P.D. equipment which is fully
compliant with the IEEE 802.3af/at PoE standards, and provide the DIP
switch configurator for High power PoE management.
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Features
I N D U S T R I A L
G I G A B I T
I n j e c t o r
P o E
Industrial Gigabit PoE++ Injector
INJ-101GT++-100W Series
PoE++ Injector for 1x10/100/1000Base-T(X)
Fully compliant with IEEE802.3at/802.3af standard
Auto protection for Over Voltage Power Input and over current output
Supports totally Power Output up to 100 Watts
Support wide range power input, 12 to 57VDC (-24V Model Only)
Provided DIP switch configurator for PoE mode management
High reliability and rigid IP-30 housing
DIN-Rail and wall-mount enabled
1. Gigabit PoE port
2. PoE indicator
3. DIP switch for PoE mode
4. Gigabit Data port
5. PoE power indicator
PWR
10/100/1000T
Dat a IN
PoE O UT
PoE
Syn c
PoE M ode
Asy nc
INJ-101GT++-100W-24V
1
4
5
2
3
41.0
95.0
PWR
10/100/1000T
Dat a IN
PoE O UT
PoE
Sync
PoE Mo de
Asyn c
INJ-101GT++-100W-24V
Contents Pictures Number
X 1
QIG X 1
25mm DIN-rail kit X 1
Wall-Mount Kit X 2
For INJ-102GT++
40mm DIN-rail kit X 1
Wall-Mount Kit X 2
For INJ-102GT++-24V
INJ-101GT++-100W or
INJ-101GT++-100W-24V
Installation
Preparation
Before installation, make sure you have all of the package contents available and a PC
with Microsoft Internet Explorer 6.0 or later, for using web-based system management
tools.
Elevated Operating Ambient: If installed in a closed environment, make sure the operating
ambient temperature is compatible with the maximum ambient temperature (Tma)
specified by the manufacturer.
Make sure the amount of air flow required for safe operation of theReduced Air Flow:
equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a hazardous
condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
Safety & Warnings
21.9
13.1
24.7
22.52
DIN-rail
Step 1 : Slant the device and screw the Din-rail kit onto the back of the device, right in the middle of
the back panel.
Step 2 :Slide the device onto a DIN-rail from the Din-rail kit and make sure the device clicks into the
rail firmly.
Backplane-Mount
Step 1: Screw the two pieces of backplane-mount kits to the top and bottom panels of the device. A
total of ight screws (mertric 3 x3) are required, as shown below.e
Step 2: Use the device, with wall mount plates attached, as a guide to mark the correct locations of
the four screws.
Step 3: Insert a screw head through middle of the keyhole-shaped aperture on the plate, and then
slide the device downwards. Tighten the screw head for added stability.
70.0
43.5
33.6
8.0
14.0 13.5
40.0
50.0
25.3
29.0
41
24.7
Ø5.9
Ø3.0
Dimension Unit =mm (Tolerance ±0.5mm)
INJ-101GT++-100W-24V
43.5
8.0
14.0 6.05
25.0
50.0
25.5
12.3
13.1
24.3
25.6
24.3
Ø5.9
Ø3.0
21.9 22.52
70.0
INJ-101GT++-100W
Panel Layouts
Front Panel
1. Din-rail screw holes
Rear Panel
1
Top Panel
1
1. Terminal block
2. Wall-mount screw holes
2
1
1
2
26.1
95.0
PWR
10/1 00/100 0T
INJ-101GT++-100W
Dat a IN
PoE O UT
PoE
Sync
PoE Mo de
Asyn c
PWR
10/100/1000T
INJ-101GT++-60W
Dat a IN
PoE O UT
PoE
Sync
PoE M ode
Asyn c
1
4
5
2
3
INJ-101GT++-100W Series

Q I G Quick Installation Guide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
Q I G
Version 1.0
ORing Industrial Networking Corp.
Copyright© 2018 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oringnet.com
E-mail: [e-mail]
I N D U S T R I A L
G I G A B I T
I n j e c t o r
P o E
Industrial Gigabit PoE++ Injector
Network Connection
The device has standard Ethernet ports. According to the link type, the AP uses CAT
3, 4, 5, 5e, 6 UTP cables to connect to any other network device (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable specifications.
Cable Type Max. Length Connector
10BASE-TX Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000BASE-T Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m (328ft) RJ-45
For pin assignments for different types of cables, please refer to the following tables.
10/100 Base-TX
1000 Base-T
RJ-45 Input (Data Only)
RJ-45 Output (Data and Power)
Pin
Symbol
Description
Symbol
Description
1
BI_DA+
Data BI_DA+
BI_DA+
(Vdc1+)
Data BI_DA+ and
Feeding Power(+)
2
BI_DA-
Data BI_DA-
BI_DA-
(Vdc1+)
Data BI_DA- and
Feeding Power(+)
3
BI_DB+
Data BI_DB+
BI_DB+
(Vdc1-)
Data BI_DB+ and
Feeding Power(-)
4
BI_DC+
Data BI_DC+
BI_DC+
(Vdc2+)
Data BI_DC+
Feeding Power(+)
5
BI_DC-
Data BI_DC-
BI_DC-
(Vdc2+)
Data BI_DC-
Feeding Power(+)
6
BI_DB-
Data BI_DB-
BI_DB-
(Vdc1-)
Data BI_DB- and
Feeding Power(-)
7
BI_DD+
Data BI_DD+
BI_DD+
(Vdc2-)
Data BI_DD+
Feeding Power(-)
8
BI_DD-
Data BI_DD-
BI_DD-
(Vdc2-)
Data BI_DD-
Feeding Power(-)
RJ-45 Input (Data Only)
RJ-45 Output (Data and Power)
Pin
Symbol
Description
Symbol
Description
1
Rx+
Data Receive
Rx+
(Vdc1+)
Data Receive and
Feeding power(+)
2
Rx-
Data Receive
Rx-
(Vdc1+)
Data Receive and
Feeding power(+)
3
Tx+
Data Transmit
Tx+
(Vdc1-)
Data Transmit and
Feeding power(-)
4
NC
Not Connected
NC
(Vdc2+)
Not Connected
Feeding power(+)
5
NC
Not Connected
NC
(Vdc2+)
Not Connected
Feeding power(+)
6
Tx-
Data Transmit
Tx-
(Vdc1-)
Data Transmit and
Feeding power(-)
7
NC
Not Connected
NC
(Vdc2-)
Not Connected
Feeding power(-)
8
NC
Not Connected
NC
(Vdc2-)
Not Connected
Feeding power(-)
PWR
10/100/1000T
Dat a IN
PoE O UT
PoE
Sync
PoE M ode
Asyn c
INJ-101GT++-100W-24V
Configurations
After installing the device and connecting cables, the green power LED should turn on.
Please refer to the following table for LED indication.
LED
Color
Status
Description
Power Green On Power is on and functioning Normally
PoE Blue
On PoE Device Link
Off None PoE Device Detected
Blink Overload present
Specifications
ORing PoE Injector Model INJ-101GT++-100W-24V
10/100/1000Base-T(X) P.S.E.
Port in RJ45 Auto MDI/MDIX 1
Physical Ports
Operating Voltage
Input Voltage 50 ~ 57 VDC on 4-pin terminal block
LED Indicators
PWR: 1 x LED
Green On: Power is on and functioning Normally.
Power indicator
PoE Ind icator
Protection
Short Circuit Protection
Over Load Protection
Present
Physical Characteristic
Enclosure IP-30
Dimension (W x D x H) 26.1(W) x 70(D) x 95(H)mm
(1.03x 2.76 x 3.74inch.)
Weight (g)
Environmental
-40 to 85 C (-40 to 185 F)
o o
Storage Temperature
Operating Temperature
5% to 90% Non-condensingOperating Humidity
Regulatory Approvals
CE EMC (EN 55024, EN 55032), FCC Part 15BEMC
EN 55024 (IEC/EN 61000-4-2 (ESD), IEC/EN 61000-4-3 (RS),
IEC/EN 61000-4-4 (EFT), IEC/EN 61000-4-5 (Surge),
IEC/EN 61000-4-6 (CS), IEC/EN 61000-4-8(PFMF),
IEC/EN 61000-4-11 (DIP))
EMS
IEC60068-2-27Shock
IEC60068-2-31
Free Fall
1 x LED
Blue On: PoE Device Link
Off : None PoE Device Detected
Blink (Blue) : Overload present
188 g
-40 to 75 C (-40 to 167 F)
o o
10/100/1000 Base-T(X) Ports
in RJ45 Auto MDI/MDIX 1
Present
INJ-101GT++-100W
12 ~ 57 VDC on 4-pin terminal block
41(W) x 70(D) x 95(H)mm
(1.61x 2.76 x 3.74inch.)
318 g
EN 55032, CISPR32, EN 61000-3-2, EN 61000-3-3, FCC Part 15B class AEMI
EN60950-1 Safety
MTBF
2570121hrs
Warranty
5 years
2300627hrs
PoE Mode
DIP Switch 1/2
*Note1
DIP Switch 1/2 (OFF): PoE P.S.E set to master and Asyncronize mode.
DIP Switch 1/2 (ON) : PoE P.S.E set to Syncronize mode(default)
Power
Input Power
Power Consumption
50 ~ 57 VDC on 4-pin terminal block
1 Watts (Not include PD's device)
12 ~ 57 VDC on 4-pin terminal block
PoE Power Budget 90Watts at 50VDC
100 Watts at 54VDC
30Watts at 12~24VDC
100Watts at 24~57VDC
IEC60068-2-6Vibration
Note1: (1) By default, the output value of the high power PoE++ is in sync mode supports PoE
af/at-compliant P.D. devices.
(2) If you cannot enable the 60W PTZ camera, please set the DIP switch to Async mode
and reconnect power. This mode only supports Dual P.D mode. You may not connect
to an af/at-compliant P.D. device with this mode.
INJ-101GT++-100W Series
INJ-101GT++-100W Series