OS S-R1 User manual
Infrared Remote Controller
Please kindly read this instruction manual carefully and use the product properly. This
manual should be kept for future reference.
Index
Safety Precautions 23
Accessories 4
Cautions in handling 4
Fitting the nfrared receiver 5
Preparation of the remote controller 5
How to use 6
Change of projection position 67
FAQ
Instruction Manual
To our Customers:
Thank you for purchasing this.
This manual deals with the infrared remote
controller and the receiver. Please refer to
the screen manual for the operations of the
electric screen.
S-R1 / Infrared Remote Controller
This icon warns that it may cause death or casualty if not following
the instruction closely.
This icon indicates that it may cause injury or damage to the
property.
Safety Precautions
Please strictly comply with the following for safety
This instruction manual is intended to prevent any danger to the user and the th
i
r
d parties, or any damage to the
property. The following indicators are to remind users to strictly observe the instructions.
Throughout our explanation, the possible damage which may be caused by any negligence or
disregard of the safety precaution is classified to different levels according to
For the precautions we recommend users to notice, we explain by using the following
different categories
(The following
are
just example
s
)
.
This icon suggests that the action is strictly prohibited.
This icon suggests that this is the necessary procedure to follow.
!
"
OS Screen would not be responsible for damage caused by improper installation or natural disaster factors.
#$% $
Accessories
nfrared receiver &' Spare sticker(spare) &'
Cautions in handling
Please comply with the following cautions carefully, when you use the product.
!The distance the remote controller can be used is subject to the various environments, and can
sometimes be shorter.
!Do not use in the rain and water because it is not waterproof.
!Change the two AAA batteries to the new ones when the signal is weak.
!Do not put in the back pocket of your trousers. When you sit down, the pressure might
damage the remote controller.
!When it is dirty, remove the dust with the soft dry cloth.
!Never use a chemicals such as benzene, thinner etc. for cleaning.
!Do not drop the remote controller or give a strong shock.
!Do not store it in the direct sunshine area.
nfrared remote controller&' AAA dry batteries&(
Please confirm if every accessories are ready. f
anything is missing, please contact the dealer or
distributor.
' Connect the modular plug of the nfrared receiver to the modular jack
( Remove the dust, water, oil and moist on the location, and stick the nfrared receiver tightly,
peeling the coated paper off. The location should be where the signal of the infrared remote
controller can reach. Avoid the direct sunshine area.
Fitting the Infrared receiver
Things to know:
When the reception is weak because of the direct sunshine, the infrared receiver location should be changed.
There are locations where the infrared receiver cannot be stuck.
Use the spare sticker, when the adhesive power of the pad is weak.
Make sure the power is off when you connect it to the screen. t
may destroy the product.
Plug in the nfrared receiver plug tightly. f not, it may cause
mal-functioning.
Please pull out the back panel of the remote controller, and put two dry batteries
(size AAA).
Dry batteries
Change the two batteries to the new ones
when the signal is weak.
Take out all the batteries when you do not
use it for long to avoid the liquid leakage
damage
Do not use rechargeable batteries.
Preparation of the remote controller
Batteries (UM4)
Make sure and
are correct.
Remote controller
Do not drop, throw away, or put water on it, or it
may cause the breakdown.
Handle the remote controller carefully.
Please operate it to the direction of the infrared
receiver
Modular type
Infrared
receiver
The operation range of Infrared remote controller
Infrared receiver
How to use
Pull out the power plug, when the screen is not used for long.
The leak may cause a fire.
Storing the screen
When the screen is deployed, push the
button of
the remote controller.
The screen is rolled up and stored, and it stops
automatically.
Stopping the screen
Please push the
button whenever you want to
stop the operation.
Deploying the screen
Please confirm the screen is stored, and push the
button of the remote controller. The screen is
deployed to a prescribed projection position, and it stops
automatically.
Change of projection position
The projection position can be changed as desired.
To lift up the projetion positon
! Stop at the desired position
Use
&
buttons and push
button at the desired position.
" Memorizing the position
1. At the desired position, push
button
for 5-6 seconds, and then push
button within 2 seconds.
2. Upon receiving the command, the screen
moves up approx. 10cm, and then
stops at the preset position.
UP button
(The screen moves up.)
TOP button
(The screen stops.)
DOWN button
(The screen moves down.)
To lift down the projection position
! Deploy the screen
Push
button for 5-6 seconds
and the screen starts to come down from
the preset position.
Push
button.
" Stop at the desired position
Use
&
buttons and push
button at the desired position.
# Memorizing the position
3. ' At the desired position, push
Button for 5-6 seconds, and then push
button within 2 seconds.
Upon receiving the command, the screen moves up
approx. 10cm, and then stops at the preset position.
$NOT CE
f the
button is pushed for some time and left as it is, the screen
comes to the factory default position, and stops. The screen cannot be lower than this position.
%&'
n case of malfunctions, please refer to the following table before asking for the repair work.
Make sure the power plug is disconnected before checking. f the problem is not solved, please
consult with the dealer or the distributor.
Symptom Check Remedy
s power plug fixed to the mains
correctly?Fix the plug tightly.
s the remote controller directed
to the receiver?
Direct the remote controller to
the receiver.
Anything blocking between the
remote and receiver?
Take off the blocking item, or
change the receiver position.
s the sun or lights reflected on
the receiver?
Change the position of the
receiver
Batteries of remote low?Change the two batteries in the
remote.(AAAtype)
s the heat prevention circuitry
on?
Cool off the motor and operate
again after 10-20 minutes.
Reset the stored position, using
UP operation.
s the receiver cable extended?
f the receiver cable is extended,
it is easily affected by the noises.
Any modifications on the product
or the accessories would be
subject to non-warranty.
The screen does not operate
s there a power failure during
operation?
f the power fails during
operation, UP or DOWN
operation restores the screen to
reset.
No adjustments on the lift
down position
Conf nfrared m the procedures
explained in the manual.
Store up the screen, and wait
more than 1 second for
re-setting.
OSI CO., LTD.
Room 1605, 16/F, Seaview Centre, 139 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
PHONE : +852- 580-0087 FAX : +852-2 67-4 00
E-mail : info-hk@os-worldwide.com
U R L : http://www.os-worldwide.com
Table of contents
