OSEPP DIY-006 User manual

OSEPP USA, INC.
2105 S Hardy Dr., Unit # 19
Tempe, Arizona, 85282
USA
www.osepp.com
Spinning Wheel DIY Solder Kit
Cat #: DIY-006
Learn to solder with easy-to-follow instructions. Idea for hobbyists and education institutes.
Kit Contents:
Component
Name
Value
Qty
Designator
Important Info
Image Reference
LED 5mm
5mm
24
LED1…. LED24
Watch the
polarity. Long leg
is positive (+)
Mini Push Button
6x6mm
2
KEY1, KEY2
No polarity
Resistors
330 ohms
6
R1…. R6
No polarity
24 LEDs (extras included)
Spinning sound
1 to 12 LED spin selection
Push button operation
2xAAA battery power (not Incl.)
Microprocessor technology
Auto power off in 2 min

OSEPP USA, INC.
2105 S Hardy Dr., Unit # 19
Tempe, Arizona, 85282
USA
www.osepp.com
Buzzer
3V
1
BUZZER1
Watch the
polarity
Integrated Circuit
(IC)
STC15W204S
1
U1
Match the ‘notch’
on the silkscreen
to the notch on
the IC.
Battery Clip
AAA
4
BT1, BT2, BT3,
BT4
Pay attention to
the placement
direction.
Capacitor
100nF
1
C1
No polarity
Desoldering Braid
6” long (2.5mm
width)
1
n/a
Use to remove
solder when
correcting
mistakes

OSEPP USA, INC.
2105 S Hardy Dr., Unit # 19
Tempe, Arizona, 85282
USA
www.osepp.com
100 ohms
Brown/Black/Brown/Gold
300 ohms
Orange/Orange/Brown/Gold
1 MEG
Brown/Black/Green/Gold
1K ohms
Brown/Black/Red/Gold
10K ohms
Brown/Black/Orange/Gold

OSEPP USA, INC.
2105 S Hardy Dr., Unit # 19
Tempe, Arizona, 85282
USA
www.osepp.com
Step-by-Step Instruction
STEP 1: Place and solder IC into place
•Match the ‘notch’ on the IC to the notch on the PCB silkscreen image.
STEP 2: Place and solder the resistors into place.
•There is no polarity with the resistors

OSEPP USA, INC.
2105 S Hardy Dr., Unit # 19
Tempe, Arizona, 85282
USA
www.osepp.com
Step 3: Place and solder the capacitor in place.
•There is no polarity with the capacitor.
Step 4: Place and solder the mini switches into place.
•There is no polarity with the mini switches.

OSEPP USA, INC.
2105 S Hardy Dr., Unit # 19
Tempe, Arizona, 85282
USA
www.osepp.com
Step 5: Place and solder the buzzer.
•Watch for polarity. Refer to the under side of the buzzer for polarity label.
Step 6: Place and solder the LEDs (x24) into place.
•The longer lead on the LED is positive (+).
•To hold the LED in place to solder, bend the lead on the back of the PCB.
•A diagonal cutter is required (not Incl.) to cut off the leads after soldering.

OSEPP USA, INC.
2105 S Hardy Dr., Unit # 19
Tempe, Arizona, 85282
USA
www.osepp.com
Step 7: Place and solder the battery clips (x4) into place.
•Please refer to the image below for battery clip placement.
Step 13: Finished image reference