OSP Designs AURORA AR2544R User manual

AR2544R
AURORA COMPUTER DESK
ASSEMBLY INSTRUCTIONS
LIMITED WARRANTY
OSP Designs Warrants, to the original purchaser its products to be free from defects in material and workmanship for a period of 90 days. Defects
and damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other event beyond the control of OSP
Designs is not covered. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or consequential
damages is excluded. The user assumes all risk of injury resulting from use of this product. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
To make a warranty claim, contact Customer Service, provide model number, sales receipt and description of the problem. It is the customer’s
responsibility to prepay freight on any components returned to the factory. OSP Designs will pay return freight on components covered under
terms of warranty.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when hardware is missing.
Our Parts Department will do everything possible to promptly remedy the problem. Contact us via email parts@officestar.net, by Fax
1-909-930-5629, or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time. OSP Designs P.O. Box
3520 Ontario, California 91761 USA
WARNING
1. Do not use this product unless all screws and bolts are securely
tightened.
2. Check that all screws and bolts are tight every three months or as
needed.
3. Dispose of packing material properly. Do not use plastic cover as
head covering. It may cause suffocation.
4. Do not use this product as a stepladder.
5. Use this product for its intended purpose only.

If you need to remove the drawer with ball bearing slides from the unit, follow the
steps below to prevent any damage to the slides or the drawer.
If you need to remove the drawer, please pull the drawer all the way out, then push the plastic release
lever of the ball bearing slide up on one side and down on the other side, and then pull the drawer
completely out. See detail #A.
DRAWER INSTALLATION
Detail #A
Detail #B
To place the drawer back, simply push the ball bearing cart all the way to the end of the slide (in both sides),
and align the slide runners on the drawer with the slide tracks on the unit and push it carefully inside until
it stops. See detail #B.
Note: If they do not align properly, remove and repeat step 2

PARTS LIST
(C) Right Side Panel (1 PC) (D) Left Wood Leg (1 PC)
(E) Right Wood Leg (1 PC) (F) Metal Post (2 PCS)
(G) Left Bottom Panel (1 PC) (H) Right Bottom Panel (1 PC)
(I) Back Panel (1 PC) (J) Cross Bar (1 PC)
(A) Top Panel (1 PC) (B) Left Side Panel (1 PC)

PARTS LIST
(M) Right Drawer Side (1 PC) (N) Drawer Back (1 PC)
(K) Drawer Bottom (1 PC) (L) Left Drawer Side (1 PC)

HARDWARE LIST
DRAWINGNO DESCRIPTION SIZE QUANTITY
1
2
3
4
5
6
7
8
9
10
11
12
13
Cam Bolt 8 PCS + 1 Extra
8 PCS + 1 Extra
2 PCS
4 PCS + 1 Extra
4 PCS + 1 Extra
8 PCS + 1 Extra
1 PC
18 PCS + 3 Extra
12 PCS + 2 Extra
2 PCS
1 PC
1 PC
1 Set
Cam Lock
Wooden Dowel
Bolt
Bolt
Bolt
Allen Wrench
Wood Screw
Wood Screw
Glide
Knob
Screw
Anti-Tip Kit
8 x 40 mm
1/4’’ x 35 mm
1/4’’ x 25 mm
1/4’’ x 13 mm
4 mm
M4.2 x 32 mm
M3.5 x 13 mm
5/32’’ x 38 mm

STEP 1
STEP 2
(1)
(D)
(A)
180°
(E)
(3)
(B)
(A)
(2)
(C)

STEP 3
STEP 4
(7)
(6)
(G)
(H)
180°
(7)
(5)
(2)
(7)
(4)

STEP 5
STEP 6
(8)
(4)
(7)
(6)
(7)
(10)

STEP 7
STEP 8
(9)
(L)
(M)
(N)
(8)

STEP 9
STEP 10
(4)
(12)
(8)
(11)
(9)
(10)
(10)

STEP 11
SEE DRAWER
INSTALLATION PAGE
IMPORTANT: FULLY TIGHTEN ALL BOLTS & SCREW BEFORE USING

Long Screw
Short Screw
Bracket
Mount
Anchor
Safety Strap
WALL
ANTI-TIP KIT INSTALLATION