Ostermann 508.4033 User manual

SAFETY INSTRUCTIONS
• Make sure that no installation and connection wires are
damaged during installation!
• Do not use the device if it is damaged!
• Protect the device from moisture, water or heat!
• Do not operate the device in the immediate vicinity of flam-
mable gases, vapors and / or dust!
• Do not expose the product to heavy mechanical pressure!
• LED components are generally operated with so-called
protective low voltages (i.e. 12V or 24V). Do not connect any
components directly to 230V~, except when the respective
installation and operating instructions as well as the labeling
on the device does not explicitly specify this (for example,
primary side of power supplies). It can be fatal!
• Be sure to follow the safety instructions and documenta-
tion of any other appliances that are connected to these
devices!
• In commercial facilities, the safety regulations of the
professional trade association for electrical installations and
equipment must be observed.
• The product is not a toy! It contains small parts that can be
swallowed by children!
COMMISSIONING
In addition to operate the LED professional dimmer remote control
you need a number of LED professional dimmers tailored to your
application. Connecting the LED professional dimmer, please perform
according to the installation instructions that come with the LED
professional dimmer.
To operate the LED professional remote control please use 3x 1.5V
AAA batteries. These are not included. Open the battery compart-
ment on the back of the remote control and insert the batteries
observing the direction indicated in the battery compartment. Close
the battery compartment again.
Once you have all the components connected properly, you can learn
the LED professional dimmer to the remote control to operate it.
NOTE: With the LED professional remote control four zones are
available, allowing you i.e. to control four different rooms or areas
independently. In each zone any number of LED professional dimmer
can be taught, each LED professional dimmer can in turn be cont-
rolled by a maximum of eight remote controls. Each zone requires
a „master“ receiver that synchronizes the other receivers within its
zone. The setting of the “master” takes place on the LED professional
dimmer by opening and closing the plug-in contact („Jumper“), which
is located next to the terminals for the supply line (jumper closed =
Master). Be sure to define exactly one master for each zone.
LED Professional remote control
Part-no.: 508.4033
User manual
INTENDED USE
The LED professional dimmer is used to power and control LED
modules, i.e. LED strips (sold separately). Both the LED professional
remote control as well as the other components of this system are
designed exclusively for use in dry indoor locations. The LED professi-
onal remote control is used to control the LED professional dimmer
by radio signals. The LED professional dimmer may only be operated
with a suitable converter, which is approved for the operation of
lamps and works with a constant output voltage between 9V and
36V DC. In addition, only LED modules may be connected, that can
be operated with a constanst voltage, which corresponds to the
output voltage of the LED converter.
Changes to the device or components can cause damage to it and in
addition can lead to potential risks such as short circuit, fire, electric
shock, etc. For injury or damage arising from improper use, not the
manufacturer but the operator is responsible.
Damage resulting from failure to observe the safety and installation
instructions will void all warranty claims. The manufacturer will not
be liable for any resulting consequential damage. Technical changes
that do not affect the contents of this installation and operating
instructions are reserved.
INTRODUCTION
Thank you for choosing a product from Rudolf Ostermann GmbH. We
want you to have a lot of fun with your new product and therefore ask
you to read these installation and operating instructions carefully. They
contain important information for installation and operation. Take care
if you pass the product on to third parties. Keep this document on file
for future reference.
LEARNING PROCEDURE
1. Turn on the LED professional remote control
2. Turn on the power supply of the LED professional dimmers to
be programmed
3. Press the programming button on the LED professional dimmer
4. To program the receiver to the desired zone, press the buttons
1 (= Zone 1), 2 (= Zone 2), 3 (= Zone 3) or 4 (= Zone 4) on the
remote control and then touch the area in the middle of the
remote control. The LED modules connected to the LED profes-
sional dimmer flash to show that the programming is done.
5. To program another receiver, follow the steps 2,3 and 4 again.
After successfully programming all LED professional dimmers and
remote controls the system is immediately ready for use.
RESET TO FACTORY SETTINGS
In case of failure or after conversion, you can reset the receiver to
factory settings. Hold the programming button on the respective re-
ceiver and keep it pressed (about 5 seconds) until the connected LED
modules flash briefly. The reset is performed successfully.
OPERATION
Turn on the remote control with a short press on „ON / OFF“ (signal
LED is blue) and then select the zone to be controlled by briefly pres-
sing the corresponding number. You can now select the functions as
described below.
FUNCTIONS
Zone
1-4
Quick select
25% brightness
Quick select
75% brightness
Quick select
100% brightness
Quick select
50% brightness
Touch pad to select
brightness
Status display
Memory 1 - 3
1 42 3
S1 S2 S3
Touch pad
ON/OFF
1, 2, 3, 4 Touch shortly = selects zone
Hold = switches zone on or off
Note: If you press briefly the zone keys in succes-
sion, these are controlled jointly. The pairing is
separated again by selecting a single zone.
Dimming = from right to left to increase bright-
ness
S1, S2, S3 Load memory = Touch S1 or S2 briefly
Save memory = Set brightness, press S1 or 2 for
about 2 seconds
The successful saving is confirmed by flashing of
the connected light source.
Note: For each zone 3 memory spaces are
available.
Note: All changes will be apply only to the active zones.
Press and hold to increase or decrease bright-
ness infinitely. After each press of the button, the
dimming direction changes.
Using the quick select buttons, you can call up pre-
set brightness values (25%, 50%, 75%, 100%).
Brightness
ON/OFF

Within the EU, this symbol indicates that this
product may not be disposed of with household
waste. Please dispose of used electrical equip-
ment through the appropriate collection systems
or send the device back to where you bought it
for proper disposal. Your dealer will ensure the
device is properly recycled.
PROPER DISPOSAL
Batteries containing harmful substances are
provided with a mark consisting of a crossed out
dustbin and the chemical symbol (Cd, Hg or Pb) of
the pollutant crucial heavy metal.
ATTENTION!
Batteries do not belong in the household waste. You are legally obli-
ged to return batteries. You can return this after use in a communal
collection point or at your dealers shop.
508.4033
Frequency 868 MHz
Operating temperature -10°C - +60°C
Dimension (LxWxH) 132 x 44 x 25 mm
TECHNICAL DATA
SUPPORT, GUARANTEE OR WARRANTY
If you need technical assistance with installation, commissioning or use
of the products, if you suspect an error or defect or want to enforce gua-
rantee or warranty claims, please always first contact your dealer where
you purchased the product. Only then you can be helped quickly and easily.
CARE, MAINTENANCE, REPAIR
To clean the product, it is sufficient to wipe the surface with a dry or
damp cloth. Make sure that no moisture penetrates and do not use any
aggressive cleaning agents which possibly attack the material and can
damage the device.
Inside the device there are no user-serviceable parts! In case of a techni-
cal defect please contact qualified personnel.
Stand: 28.09.2015