Outback Mayfair User manual

0359
Photographs are not to scale.
Specifications subject to change
without prior notice.
Elite Series Barbecues
Assembly and Operating Instructions for Outback®
Mayfair/Tungsten, Spirit/Titanium, Hooded Gas Barbecues
EN (Europe)
WARNING
• For outdoor use only. Not for commercial use.
• Read instructions before using the appliance.Failure to follow instructions
could result in death, serious bodily injury, and/or property loss.
• Warning: accessible parts may be very hot. Keep young children away.
• Do not move the appliance during use.
• Turn off the gas supply at the gas bottle after use.
• Any modification of the appliance, misuse, or failure to follow the instructions
may be dangerous and will invalidate your warranty. This does not affect your
statutory rights.
• Retain these instructions for future reference.
• Leak testannually, and whenever the gas bottle is removed or replaced.
• For Flare-up control please refer to the ‘OPERATION’ section of this manual.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open barbecue lid or hood.
4. If odour continues,discontinue use and
contact your local dealer.
FOR YOUR SAFETY
1. Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
2. A gas bottle not connected for use shall not be
stored in the vicinity of this or any other
appliance.

2
Parts List
Quantities vary according to model purchased. Specifications subject to change without prior notice. For
more details on hardware,please see ‘Hardware Reference Diagram’.
Pre-Assembled Component
Quantity varies according to model purchased
 Appearance, size, and constructionmay differ according to modelpurchased
CODE PART QTY Mayfair/Tungsten Spirit/Titanium
HOOD
A1 Hood Handle 1  
A2 L/H Hood Handle Bracket 1  
A3 R/H Hood Handle Bracket 1  
A4 Hood (Pre-Assembled to Body) 1  
A5 Hood Panel 1  
A6 Heat Indicator and Nuts 1  
BODY
B1 Barbecue Body 1  
B2 Burner 2 3
B3 Control Panel 1  
B4 Knob 2 3
B5 Drip Tray 1  
B6 Large Cooking Grill 1  
B7 SmallCooking Grill 1  
B8 SmallCooking Griddle 1
B9 Flame Tamer/Lava rock in basket  
B10 Warming Rack 1  
B11 Hose (if supplied) 
TROLLEY
C1 L/H Side Shelf 1  
C2 Side Shelf Shield 1  
C3 Front Left Endcap 1  
C4 Rear Left Endcap 1  
C5 Utensil Tray 2  
C6 R/HSide Shelf 1  
C7 R/H Insert 1  
C8 Front Left Leg 1  
C9 Rear Left Leg 1  
C10 Front Right Leg 1  
C11 Rear Right Leg 1  
C12 BottomSlatAssembly 1  
C13 Base Tray 1  
C14 Gas Bottle Holder 1  
C15 Trolley Foot 1  
C16 Hubcap 2  
C17 Wheel 2  
C18 Locknut 2  
C19 Axle 1  
C20 Retaining Rod 1  
C22 Side Shelf Hook 2  
HARDWARE
D1 Countersunk Screw, M4x15 4  
D2 Screw, M6x15 24  
D3 Washer 4  
D4 Screw, M6x35 16  
D5 Screw, 1/4UNCx12 6  
C21 Gas Bottle Strap 1  

3
Parts Diagrams
Quantities vary according to model purchased. Specifications subject to change without prior notice. For
more details on hardware,please see ‘Hardware Reference Diagram.’
B7
B9
A1
C2
B3
B4
B5
B2
C3
C5C4C1 C6
A4
A2 A3
C12
B8
B10
B11
B6
C15
C14
C16
C17
C18
C19
C9
C8
C11
C21
C20
C7
C10
A6
A5
B1
C13
C22
or

4
Hardware Reference Diagram
Specifications subject to change without prior notice.
D1
D2
D2 (screw)
D3(washer)
D2
D4
D5

5
Attach the Front Right Leg (C10) to the Trolley Foot (C15)
Assembly
IMPORTANT!
• Tools Required: Medium size flat blade or Phillips/Crosspoint screwdriver, adjustable spanner or metric
spanner set
• The assembly of this barbecue requires 2 people.
• Carefully unpackthe trolley box and remove all internal packaging beforecommencing assembly.
• Carefully remove the box lid from the body box and remove all internal packaging and parts inside the
body.
• The inletconnection of the gas rail assembly on the BBQ bodyis lower than the body. You must never
allow the pipe to rest onthe ground during assembly as serious damage could result. We recommend
the body is left sitting in the box until required for assembly to trolley.
• Whilst every care is taken in the manufacture of this product, care must be takenduring assembly in
case sharp edges are present.
2
1
Attach the Rear Right Leg (C11) to the Trolley Foot (C15). The legs are a push fit onto the trolley foot
and on the gas bottle holder. In case of difficulty, they may need tapping lightly with a soft face mallet.
Take care not to damage parts.

6
Attach the Bottom Slat Assembly (C12) to the Base Tray (C13) using the Screws (D2).
Attach the leg assembly to the Base Tray (C13)using the Screws (D2).
4
3

7
Align the Gas Bottle Holder(C14) with the Slat Assembly (C12).
Attach the Front Left Leg (C8) and Rear Left Leg (C9)to the Gas Bottle Holder (C14).
Note:Threaded inserts must be facing in the direction shown!
6
5
Threaded
Insert

8
Attach the Gas Bottle Holder (C14) to the Bottom Slat Assembly (C12) using the Screws (D2)
and Washers (D3).
Insert the Axle (C19) into the Gas Bottle Holder (C14).
8
7

9
Place the Wheels (C17) onto the Axle (C19) and secure with Locknuts (C18).
Carefully turn the completed trolley over, right side up.
10
9
Remove all cast iron cooking components, Flame Tamer/ LavaRock , drip tray, and
any internal packaging from the barbecue body.
Note: Loosen off the bolts and move the brackets down to their lowest position.
Retighten the bolts.
B5
B7
B9
B8B6
or

10
CAUTION! Care must be taken to ensure hood does not fall open
unexpectedly or that the hood surface is damaged when set on the ground.
Attach the R/HSide Shelf (C6) to the Barbecue Body (B1)using the Screws (D2).
Attach the Front Left Endcap (C3)to the Body(B1) using the Screws (D2).
12
11