Outback THG3710SS-3 User manual

Assembly and Operating Instructions for Outback®
Excelsior Select 3 Burner and Excelsior Select 6 Burner Gas BBQ
Photographs are not to scale.
Specifications subject to change
without prior notice.
WARNING
• For outdoor use only. Not for commercial use.
• Read instructions before using the appliance. Failure to follow instructions could result
in death, serious bodily injury, and/or property loss.
• Warning: accessible parts may be very hot. Keep young children and pets away.
• Do not move the appliance during use.
• Turn off the gas supply at the gas bottle after use.
• Any modification of the appliance, misuse, or failure to follow the instructions may be
dangerous and will invalidate your warranty. This does not affect your statutory rights.
• Retain these instructions for future reference.
• Leak test annually, and whenever the gas bottle is removed or replaced. Check that the
hose connections are tight and leak test each time you reconnect the gas bottle.
• For Flare-up control please refer to the ‘OPERATION’ section of this manual.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open barbecue lid or hood.
4. If odour continues, discontinue use and contact
your local dealer.
FOR YOUR SAFETY
1. Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
2. A gas bottle not connected for use shall not be
stored in the vicinity of this or any other
appliance.
0359
THG3710SS-3 THG6710SS-3

2
Parts List
Quantities vary according to model purchased. Specifications subject to change without prior notice. For more
details on hardware, please see ‘Hardware Reference Diagram’.
Pre-Assembled Component
Quantity varies according to model purchased
 Appearance, size, and construction may differ according to model purchased
CODE PART QTY Outback® Excelsior
Select 3 Burner Gas BBQ Outback® Excelsior Select 6 Burner Gas BBQ
HOOD
A1 Hood Handle 1  
A2 Hood (Pre-Assembled to Body) 1  
A3 Hood Panel 1  
A4 Heat Indicator and Nuts 1  
B1 Barbecue Body 1  
B2 Burner 36
B3 Control Panel 1  
B4 Knob 36
B5 Drip Tray 1  
B6 Drip Pan 1 
B7 Drip Tray Left Bracket 1 
B8 Drip Tray Right Bracket 1 
B9 Lava Rock 1  
B10 Lava Rock Basket 1  
B11 Cooking Grill 1  
B12 Cooking Griddle 1  
B13 Hose and Regulator Assembly 1 
B14 Warming Rack 1  
TROLLEY
C1 Side Burner Shelf 1  
C2 Side Shelf Shield 1  
C3 Front Left Endcap 1  
C4 Rear Left Endcap 1  
C5 Utensil Tray 2  
C6 Side Shelf 1  
C7 Right Insert 1  
C8 Left Front Leg 1  
C9 Left Rear Leg 1  
C10 Right Front Leg 1  
C11 Right Rear Leg 1  
C12 Bottom Slat Assembly 1  
C13 Base Tray 1  
C14 Gas Bottle Holder 1  
C15 Trolley Foot 1  
C16 Hubcap 2  
C17 Wheel 2  
C18 Axle 1  
C19 Retaining Rod 1  
C20 Gas Bottle Strap 1  
C21 Side Shelf Hook 2  
C22 Fixing Bracket 2  
C23 Side Burner Grid 1  
HARDWARE
D1 M4x15 Bolt 4  
D2 M5x15 Bolt 4  
D3 Ø5 Washer 4  
D4 M5 Nut 4  
D5 M6x15 Bolt 24  
D6 Ø6 Washer 4  
D7 M6x35 Bolt 16  
D8 1/4-20UNCx12 Bolt 6  
D9 Locknut 2  
BODY

3
Parts Diagrams
Quantities vary according to model purchased. Specifications subject to change without prior notice. For more
details on hardware, please see hardware pack page.
B9
C2
B3
B4
B5
B2
C3
C5C4C1
A2
C12
B12
B10
C15
C14
C16
C17
D9
C18
C9
C8
C11
C20
C19
C7
C10
A4
A3
B1
C13
C21
B13
C22
B7 B8
B11
A1
C23
C6
B14
B6

4
Hardware Reference Diagram
Specifications subject to change without prior notice.
D1
D5
D2,D3,D4 D5,D6
D7
D8

5
Attach the Right Front Leg (C10) to the Trolley Foot (C15).
Assembly
IMPORTANT!
• TOOLS NEEDED FOR ASSEMBLY: Medium size flat blade or Phillips/Crosspoint screwdriver, adjustable
spanner or metric spanner set.
• Remove any internal component or packaging from the barbecue body.
• Whilst every care is taken in the manufacture of this product, care must be taken during assembly in case
sharp edges are present.
• Please read the Important Information section carefully before assembly and use of your barbecue.
2
Attach the Right Rear Leg (C11) to the Trolley Foot (C15). The leg is a push fit onto the trolley foot and on
the gas bottle holder. In case of difficulty, they may need tapping lightly with a soft face mallet. Take care
not to damage parts.
1
C11
C15
C11
C10
C15

6
Attach the Bottom Slat Assembly (C12) to the Base Tray (C13) using the M6x15 Bolts (D5).
Attach the leg assembly to the Base Tray (C13) using the M6x15 Bolts (D5).
4
3
C11
C13
C12
D5
D5 C15
C10C13

7
Align theGas Bottle Holder (C14) with the Bottom Slat Assembly (C12).
Attach the Left Front Leg (C8) and Left Rear Leg (C9) to the Gas Bottle Holder (C14).
Note: Threaded inserts must be facing in the direction shown!
Threaded
Insert
6
5
C14
C9
C14 C8
C12

8
Attach the Gas Bottle Holder (C14) to the Bottom Slat Assembly (C12) using the Screws
(D2) and Washers (D3).
Unscrew the Locknuts (D9) from both ends of the Axle (C18).
Insert the axle through the clamping brackets into the Gas Bottle Holder (C14) and tighten the clamp
screws. Take care not to over tighten these screws which will damage the plastic gas bottle holder.
8
7
Attach the Gas Bottle Holder (C14) to the Bottom Slat Assembly (C12) using M6x15 Bolts (D5)
and Ø6 Washers (D6).
C14
C14
C12
D5
D6
C18
D9

9
Slide the Wheels (C17) over each end of the axle. Secure the wheels into place with the
locknuts.
10
9
Carefully turn the completed trolley over, right side up.
D9C17

10
Remove all cooking components, flame tamer, and any internal packaging from the Barbecue
Body (B1).
Carefully turn the barbecue body upside-down.
CAUTION! Care must be taken to ensure the hood does not fall open unexpectedly or
becomes damaged when it is set on the ground.
Attach the Side Shelf (C6) to the barbecue body using M6x15 Bolts (D5).
12
11
Place the wheel Hubcaps (C16) onto the outsides of the wheels.
C17C16
C6
B1
D5