Outdoor Lifestyles CARODG36I User manual

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 1
Owner’s Manual
Installation and Operation
Models:
CARODG36I
CARODG36IL
CARODG42I
CARODG42IL
DO NOT DISCARD THIS MANUAL
CAUTION
• Important operating
and maintenance
instructions included.
• Leave this
manual with party
responsible for use
and operation.
• Read, understand
and follow these
instructions for safe
installation and
operation.
DO NOT
DISCARD
Installation and service of this appliance should
be performed by qualified personnel. Hearth &
Home Technologies suggests NFI certified or
factory-trained professionals, or
technicians supervised by an NFI
certified professional.
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from the
appliance and immediately call your gas
supplier or fire department.
WARNING: For Outdoor Use Only.
WARNING
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
An LP-cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
WARNING: Improper installation,
adjustment, alteration, service or maintenance
can cause injury or property damage. Read
the installation, operating and maintenance
instructions thoroughly before installing or
servicing this equipment.
WARNING! Risk of Fire!
Do not install glass doors on this fireplace.
Glass doors could cause overheating of
adjacent structures.
HOT SURFACES!
Screens and other surfaces are hot
during operation and cool down.
WARNING
• CAREFULLY SUPERVISE children in same area as
fireplace.
• Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other combustibles
away.
Hot screens will cause burns.
• Do not touch fireplace until it is cooled
• NEVER allow children to touch
fireplace
• Keep children away

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 2
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
Congratulations on selecting an Outdoor Lifestyles gas ap-
pliance—an elegant and clean alternative to wood burning
appliances. The Outdoor Lifestyles gas appliance you have
selected is designed to provide the utmost in safety, reli-
ability, and efficiency.
As the owner of a new appliance, you’ll want to read and
carefully follow all of the instructions contained in this
owner’s manual. Pay special attention to all cautions and
warnings.
This owner’s manual should be retained for future refer-
ence. We suggest you keep it with your other important
documents and product manuals.
The information contained in this owner’s manual, unless
noted otherwise, applies to all models and gas control
systems.
Your new Outdoor Lifestyles gas appliance will give you
years of durable use and trouble-free enjoyment. Welcome
to the Outdoor Lifestyles family of appliance products!
Homeowner Reference Information
Model Name: Date purchased/installed:
Serial Number: Location on appliance:
Dealership purchased from: Dealer phone:
Notes:
We recommend that you record the following pertinent
information about your appliance:
Listing Label Information/Location
The model information regarding your specific appliance can be found on the rating plate located on the inside of the
control box cover.
Congratulations
Open-flame Gas appliance - for outdoor installation only.
Not for use with solid fuel.
(Appareil à gaz à flamme n ue –
pour installation à l’extérieur seulement. Ne doit pas être
utiilsé avec un combustible solide.)
Minimum Permissible G as Supply for Purposes of Input Adjustment:
Propane Gas
Approved Minimum (De Gaz)Acceptable......................XX.X w.c (Po. Col. d’eau)
Maximum Pressure (Pression).......................................XX.X w.c (Po. Col. d’eau)
Min/Max Input BTUH: ............................................XX,XXX/ XX,XXX
Orifice Size:....................................................................#XX / .XXX
MADE
IN USA
75 71 21 5t h St. W est, Lakeville, MN 5 504 4
29LD
OUTDOOR FIREPLACE
IAS U.S. 4.96, Outdoor Fireplace
CGA-CR-97-003, Outdoor Fireplace
FOR USEAT HIGHALTITUDES. This installation must conform with local codes or,
in the absence of local codes, with the National Fuel Gas Code,ANSI Z223.1/NFPA 54,
or the Natural Gas and Propane Installation Code, CSA B149.1.
MODEL:
MODÈLE:
Model Number
Type of Gas
Gas Information

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 3
Table of Contents
1 Listing and Code Approvals
A. Appliance Certification 4
B. BTU Specifications 4
C. High Altitude Installations 4
D. Non-Combustible Materials Specification 4
E. Combustible Materials Specification 4
F. Electrical Codes 4
G. Fuel 4
2 Getting Started
A. Design and Installation Considerations 5
B. Tools and Supplies Needed 5
C. Inspect Appliance and Components 5
3 Framing and Clearances
A. Select Appliance Location 6
B. Stand-Alone Installation 6
C. Built-in Installation 6
D. Moisture Resistance 6
E. Clearances and Framing Dimensions 7
4 Appliance Preparation
A. Securing and Leveling Appliance 10
B. Flashing 10
5 Gas Information
A. Fuel Conversion 11
B. Gas Pressure 11
C. Gas Connection 11
D. Electrical Codes 12
E. Valve Access 12
F. High Altitude Installations 12
6 Electrical Information
A. IntelliFire Plus™ Pilot Ignition System Wiring 13
B. Control Module Operation 14
C. Installing the Optional Electric Kit 15
7 Finishing
A. Mantel Projections 18
B. Facing Material 18
8 Appliance Setup
A. Clean the Appliance 19
B. Optional Accessories 19
C. Pilot Shield 19
D. Install Lava Rock 19
E. Positioning the Logs 19
F. Place Remaining Lava Rock 22
G. Install Firescreen 23
9 Operating Instructions
A. Gas Fireplace Safety 24
B. Your Fireplace 24
C. Screens 24
D. Before Lighting Fireplace 24
E. Lighting the Appliance 25
F. After the Appliance is Lit 26
10 Troubleshooting
A. IntelliFire Plus™ Ignition System 27
11 Maintaining and Servicing the Appliance
A. Maintenance and Service Tasks 30
12 Reference Materials
A. Appliance Dimension Diagram 31
B. Service Parts List 33
C. Warranty 38
D. Contact Information 40
Note: An arrow () found in the
text signifies change in content.


Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 4
1
1 Listing and Code Approvals
A. Appliance Certification
This product is listed to ANSI standards for “Outdoor Open-
Flame Decorative Gas Appliances” and “Gas Fired Appli-
ances for Use at High Altitudes”.
MODELS: CARODG36I, CARODG36IL,
CARODG42I, CARODG42IL
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Outdoor Open-Flame Decorative Gas Appliances
STANDARD: ANSI Z21.97-2008
Note: This installation must conform with local codes. In the
absence of local codes you must comply with the National
Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A.
and the CAN/CGA B149 Installation Codes in Canada.
Models
Min/Max Input
BTUH
Orifice Size
(DMS)
CARODG36I (NG) 36,000/55,000 #27 / .144
CARODG36IL (LP) 29,000/50,000 #46 / .081
CARODG42I 33,000/65,000 #24 / .152
CARODG42IL 37,000/62,000 #43 / .089
B. BTU Specifications
Note: This appliance, when installed, must be electrically
grounded in accordance with local codes, or in the absence
of local codes with the National Electrical Code, ANSI/
NFPA 70, if applicable.
G. Fuel
This appliance must not be used to burn solid fuel.
C. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility or
authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce input rate 4% for each 1000 feet above
2000 feet.
• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet, consult
local gas utility.
Check with your local gas utility to determine proper orifice
size.
D. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136, Stan-
dard Test Method for Behavior of Materials in a Vertical
Tube Furnace at 750 ºC shall be considered noncombus-
tible materials.
F. Electrical Codes
If this appliance will be wired, the following applies:
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA 70-
latest edition or the Canadian Electric Code CSA C22.1.
E. Combustible Materials Specification
Materials made of or surfaced with wood, compressed
paper, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
Note: See Section 6.A. for flame adjustment.

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 5
A. Design and Installation Considerations
When planning an appliance installation, it is necessary to
determine the following information before installing:
• Where the appliance is to be installed:
- Clearance to side walls
- Location of adjacent stairwells
- Doors
- Windows
- Walkways
- Wires
- Possibility of flooding or running water
• Location of gas supply piping
• Electrical wiring requirements
• Framing and finishing details
2
2 Getting Started
The Carolina Series outdoor gas fireplace is designed for
outdoor use and may be installed as a standalone unit or
built into an outside wall.
It may be installed in screened porches and lanais that meet
these minimum requirements:
• Minimum porch area - 96 square feet
• Minimum ceiling height - 82 in.
• Minimum distance from top of appliance opening to ceiling
- 49.5 in.
A minimum of one wall can be screened but must be open to
outside ventilation. Minimum requirements are:
• Minimum screen area - 64 square feet
• Minimum screen top height - 80 in.
If this fireplace is to be installed within a wall, you must:
• Provide access to the gas controls.
• Slope outdoor floor (and hearth) away from fireplace.
• Flash the perimeter of the fireplace, corners and the
fireplace face in a manner consistent with regional
practices as required to prevent water penetration around
the fireplace or manage water that may penetrate the
fireplace. See Section 3.D. and Figure 3.1 for more
information regarding wall and enclosure construction.
The fireplace may be installed on a wood or noncombus-
tible deck.
Refer to Sections 3.D. and 3.E. for clearances.
B. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Reciprocating saw Framing material
Pliers Non-corrosive leak check solution
Hammer Gloves
Phillips screwdriver Framing square
Level Electric drill and bits (1/4 in.)
3/4 in. wrench 7/16 in. wrench
7/8 in. wrench 1/4 in. nut driver
Crescent wrench Pipe sealant
Plumb line Safety glasses
Manometer Voltmeter
Tape measure
Flat blade screwdriver
Caulking material (300ºF minimum continuous exposure
rating)
1/2 - 3/4 inch length, #6 or #8 Self-drilling screws
C. Inspect Appliance and Components
• Carefully remove the appliance and components from the
packaging.
• Remove screen package from grate, set aside.
• The gas logs are packaged separately and located on
top of the firebox along with the lava rock. The installation
manual will be found inside the firebox.
• Report any parts damaged in shipment to your dealer.
• Read all of the instructions before starting the
installation. Follow these instructions carefully
during the installation to ensure maximum safety and
benefit.
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, in-
complete or substitute components. Keep appliance dry.
WARNING! Risk of Fire, Explosion or Electric Shock! DO
NOT use this appliance if any part has been under water.
Call a qualified service technician to inspect the appliance
and to replace any part of the control system and/or gas
control which has been under water.
Hearth & Home Technologies disclaims any responsibility for, and
the warranty will be voided by, the following actions:
• Installation and use of any damaged appliance or vent
system component.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
• Installation and/or use of any component part not
approved by Hearth & Home Technologies.
Any such action may cause a fire hazard.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified
service technician, service agency or your dealer.

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 6
A. Select Appliance Location
Refer to Figures 3.1, 3.2 and 3.3.
When selecting a location for your appliance it is important
to consider where the appliance is to be installed:
- Clearance to side walls
- Location of adjacent stairwells
- Doors
- Windows
- Walkways
- Wires
- Possibility of flooding or running water
3
3 Framing and Clearances
WARNING! Risk of Fire or Burns! The appliance is hot and
wind may cause flames to reach out in front.
• Keep furniture, draperies and other combustibles away.
• Locate the appliance away from traffic areas.
• Do not block air openings.
• DO NOT place rugs, carpeting or other combustible
materials on the floor directly in front of the appliance.
• Clean up fallen leaves, branches and other combustible
materials before using the appliance.
• See Figure 3.1 for required clearances.
CAUTION! The appliance is hot and wind may cause
flames to reach out in front. Install on wood or solid
noncombustible surfaces extending full width and depth to
prevent damage.
• DO NOT install directly on carpeting, vinyl, plastic com-
posite decking or combustible surfaces other than wood.
• When installed on wood, a 16” noncombustible hearth
extension in front of the appliance is recommended.
See Figure 3.3.
NOTICE: Illustrations reflect typical installations and are for
DESIGN PURPOSES ONLY. Illustrations/diagrams are not
drawn to scale. Actual installation may vary due to individual
design preference.
B. Stand-Alone Installation
This fireplace may be installed as a stand-alone unit.
• Tape and seal all joints and corners.
• Provide proper flashing and moisture management if
installed on surfaces that may rot or otherwise be damaged
by water. (See also sections 3.C. and 3.D.)
When the stand-alone surround is constructed completely
of noncombustible materials, stand-offs may be removed to
permit a smaller structure.
• Air space clearances are not required for stand-alone
construction with noncombustible materials.
C. Built-in Installation
When this fireplace is installed into a wall, we recommend
that the wall be an exterior wall system.
• See framing measurements in Figure 3.1.
• You must maintain 1 1/2 in. (38 mm) airspace at the sides
and back of the fireplace.
• Header must be placed a minimum of 6 in. (152 mm) above
the top of the fireplace.
• Noncombustible wall sheathing material is required the
first 36 in. above the top of the firebox opening.
- Remove the existing top front (cement board) and
replace with 36 x 45 1/2 in. (minimum) cement board.
Allow overlap on the framing studs. See Figure 3.1.
• The control box MUST be relocated to be easily accessible.
See Section 5.D.
• Flash the perimeter of the fireplace, corners and the
fireplace face in a manner consistent with regional
practices as required to prevent water penetration around
the fireplace or manage water that may penetrate the
fireplace. See Section 3.D. and Figure 3.1 (CARODG36)
and 3.2 (CARODG42) for more information regarding wall
and enclosure construction.
D. Moisture Resistance
This outdoor fireplace will shed moderate amounts of wa-
ter, but is not waterproof. This appliance must be enclosed
or covered with noncombustible finish material and all joints
sealed to prevent water infiltration.
The fireplace fire box will not perform as an exterior wall.
Moisture penetration must be considered for construction
that places the fireplace in structure walls or on moisture
sensitive surfaces.
When installed on exterior walls: Hearth & Home Tech-
nologies recommends that the fireplace chase be con-
structed outside the structure’s weather envelope. Where
the platform meets the wall, use a flashing detail similar to
that required for attached decks. Chase platforms, includ-
ing hearths should slope away from the structure at 1/8 in.
to 1/4 in. per foot. The fireplace can be shimmed level.
WARNING! Risk of Fire! Maintain specified air space
clearances to appliance:
• Insulation and other materials must be secured to prevent
accidental contact.
• The chase/enclosure must be properly blocked to prevent
blown insulation or other combustibles from entering and
making contact with fireplace or chimney.
• Failure to maintain airspace may cause overheating and
a fire.
NOTICE: Soot may accumulate on the area above the firebox
opening and may require periodic cleaning.

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 7
6 in. 6 in.
6 in. min. 36 in. min.
cement
board from
the top of the
firebox
opening
36 in. min.
noncombustible
finishing
material
82 in.
(2083 mm)
floor to ceiling
0 in.
Combustible Object
36 in.
(914 mm)
Front Back
Note: If this surface is
inside the building’s
warm air envelope... ...then this surface
must be an exterior
wall system.
57 in.
(1448 mm)
minimum
1 1/2 in.
(38 mm)
56 in.
(1422 mm)
79 1/4 in.
(2013 mm)
17 in.
(432 mm)
48 in.
(1219 mm)
1 1/2 in.
(38 mm)
1 1/2 in.
(38 mm)
Control
Box
Control
Box
42 3/4 in.
(1086 mm)
minimum
header height
42 1/2 in.
(1080 mm)
minimum
header height
68 1/2 in.
(1740 mm)
minimum
to top of cement
board
17 in.
(432 mm)
Flashing
Cement Board
Control box
MUST be
relocated!
Exterior
Interior
11 1/2 in.
(292 mm)
minimum
8-1/4 in.
(210 mm)
10-5/8 in.
(270 mm)
48 in.
(1219 mm)
48 in.
(1219 mm)
Framing
36 in. minimum
(889 mm)
from appliance front
Side clearances can be zero at framing,
up to 6 inches deep
Side clearances can be zero at framing,
up to 6 inches deep
6 in. 6 in.
36 in. minimum
(889 mm)
from appliance front
Note: For actual appliance
dimensions refer to Section 12.
Figure 3.1 Appliance Locations and Framing Dimensions - CARODG36I, CARODG36IL
NOTICE: Vinyl siding must
not be placed between the
fireplace opening and the
ceiling/overhang.
NOTICE: Flash the perimeter of the fireplace, corners and
the fireplace face in a manner consistent with regional
practices as required to prevent water penetration around
the fireplace or manage water that may penetrate the
fireplace. See Section 3.D. for more information regarding
wall and enclosure construction.
E. Clearances and Framing Dimensions
CARODG36I, CARODG36IL

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 8
Framing
6 in. min.
82 in.
(2.08 m)
floor to ceiling
0 in.
Combustible Object
36 in.
(914 mm)
Front Back
Note: If this surface is inside
the building’s warm air
envelope...
...then this surface must
be an exterior wall
system.
63 in.
(1.6 m)
minimum
1-1/2 in.
(38 mm)
59-5/8 in.
(1.5 m)
82-1/4 in.
(2.1 m)
17 in.
(432 mm)
1-1/2 in.
(38 mm)
1-1/2 in.
(38 mm)
Control
Box
Control
Box
50-3/4 in.
(1.29 m)
minimum
header height
50 in.
(1.27 m)
minimum
header height
71-3/4 in.
(1.82 m)
minimum
to top of cement
board
54 in.
(1372 mm)
17 in.
(432 mm)
Flashing
Cement Board
Control box
MUST be
relocated!
Exterior
Interior
11-1/2 in.
(292 mm)
minimum
36 in. minimum
(889 mm)
from appliance front
Side clearances can be zero at framing,
up to 6 inches deep
6 in. 6 in.
Side clearances can be zero at framing,
up to 6 inches deep
6 in. 6 in.
36 in. min. (914 mm)
cement board from
the top of the firebox
opening
36 in. min. (914 mm)
noncombustible
finishing material
8-1/4 in.
(210 mm)
10-5/8 in.
(270 mm)
36 in. minimum
(889 mm)
from appliance front
54 in.
(1372 mm)
54 in.
(1372 mm)
Note: For actual appliance
dimensions refer to Section 12.
Figure 3.2 Appliance Locations and Framing Dimensions - CARODG42I, CARODG42IL
NOTICE: Vinyl siding must
not be placed between the
fireplace opening and the
ceiling/overhang.
NOTICE: Flash the perimeter of the fireplace, corners and
the fireplace face in a manner consistent with regional
practices as required to prevent water penetration around
the fireplace or manage water that may penetrate the
fireplace. See Section 3.D. for more information regarding
wall and enclosure construction.
E. Clearances and Framing Dimensions
CARODG42I, CARODG42IL

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 9
Fireplace Structure
Noncombustible mat’l
Mantel
25 in.
(635 mm)
minimum
6 in.
(151 mm)
minimum - one side only.
Alcove installations require
14 in. (356 mm) from each side
of the firebox opening.
82 in.
(2083 mm)
minimum
height
Additional Structure
or Sidewall
Ceiling or
Overhang
12 in. (305 mm)
max. combustible
mantel depth
49-1/2 in.
(1257 mm)
minimum
16 in.
(406 mm)
deep non-combustible
hearth extension recommended
when floor in front is combustible.
Figure 3.3 Clearances
WARNING! Risk of Fire!
Comply with all minimum
clearances to combustibles as
specified. Framing or finish-
ing material closer than the
minimums listed must be con-
structed entirely of non-com-
bustible materials (i.e., steel
studs, concrete board, etc).

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 10
4
4 Appliance Preparation
A. Securing and Leveling Appliance
Position, level, and secure the appliance.
• Place the appliance into position on either a wood or
noncombustible continuous flat surface.
• Level the appliance from side to side and front to back.
• Shim the appliance with noncombustible material, such
as sheet metal, as necessary.
• Nailing tabs must be moved from shipping position to
installation position and secured to framing. Bend the
two nailing tabs out on each side. See Figure 4.1.
B. Flashing
• Flash the fireplace in a manner consistent with regional
practices to prevent water penetration around the
fireplace. Due to elevated temperatures across the top of
the fireplace, metal flashing and high temperature sealant
must be used. Adhesive polymeric flashing materials may
melt.
• For brick, stone, stucco and similar construction, weep
screeds should be installed per regional codes.
• See Section 3.D. and Figure 3.1 for more information
regarding wall and enclosure construction required to
prevent moisture penetration into the structure. The
fireplace will shed moderate amounts of water but is not
waterproof.
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installa-
tion. Sheet metal edges are sharp.
Figure 4.1 Positioning and Securing Nailing Tab
NAILING TABS IN
SHIPPING POSITION
NAILING TAB BENT OUT
(FRAMING POSITION)

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 11
A. Fuel Conversion
Before making gas connections ensure appliance being
installed is compatible with the available gas type.
Any natural or propane gas conversions necessary to meet
the appliance and locality needs must be made by a quali-
fied technician using Hearth & Home Technologies speci-
fied and approved parts.
Pressure requirements for appliance are shown in the table
below.
Note: Have the gas supply line installed in accordance
with local building codes, if any. If not, follow ANSI
223.1. Installation should be done by a qualified installer
approved and/or licensed as required by the locality. (In
the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.)
Note: A listed (and Commonwealth of Massachusetts
approved) 1/2 in. (13 mm) T-handle manual shutoff valve and
flexible gas connector are connected to the 1/2 in. (13 mm)
control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
B. Gas Pressure
Proper input pressures are required for optimum appliance
performance. Gas line sizing requirements need to be
made following NFPA51.
5
5 Gas Information
Fire Risk
Explosion Risk
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
Low pressure may cause explosion.
WARNING
Note: Gas line MUST be run from right side of appliance.
These pressures can be verified through the access panel
as shown in Section E. Valve Access.
Pressure Natural Gas Propane
Minimum Inlet Pressure 5.0 inches w.c. 11.0 inches w.c.
Maximum Inlet Pressure 10.0 inches w.c. 13.0 inches w.c.
Manifold Pressure 3.5 inches w.c. 10.0 inches w.c.
C. Gas Connection
The access panel is located below the control box. It will
be easier to make gas connection after the control box is in
its final position. If necessary, relocate control box prior to
making gas connection. See Section 5.E.
• Remove the screws holding the access panel.
• Set the panel and screws aside for reinstallation.
Control Box
Access Panel
Figure 5.1 Control Box & Access Panel Locations
If control box is to be relocated, move it at this time to avoid
making the gas connection more than once.
• The incoming gas line can be installed from the bottom
of the fireplace structure, from the side or from the rear
(drilling through the cement board may be necessary).
• The incoming line should be connected to the 1/2 in.
connection on the manual shutoff valve provided with the
fireplace.
• Cut cable tie holding manual shutoff valve prior to finishing
to allow for easy access.

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 12
F. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility or
authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce input rate 4% for each 1000 feet above
2000 feet.
• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet, consult
local gas utility.
Check with your local gas utility to determine proper orifice
size.
WARNING! Rick of Fire or Explosion! Gas build-up dur-
ing line purge could ignite.
• Purge should be performed by qualified service
technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks or
open flames.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all fittings and connections with a non-corrosive
commercially available leak-check solution. DO NOT use
open flame. Fittings and connections could have loosened
during shipping and handling.
E. Valve Access
The valve and controls are located in the control box (Refer
to Figure 5.1). Remove the screws and remove the lid.
• Accessibility to the shutoff valve is required after
installation, or another accessible shutoff is required.
Figure 5.2 Connect Incoming Gas Line to Manual Shutoff Valve
Junction Box
Mounting Bracket
(used with optional
electric kit)
Valve
Control
Module
Battery Holder
Figure 5.3 Control Box
The control box is designed to be moved out to allow for
the thickness of the finish material or moved from the unit
and repositioned.
• Loosen the two bolts found inside the box in the bottom
of the control box.
• Slide the box out as necessary.
• Tighten the screws.
• The control box can be removed from the appliance and
repositioned (up to approximately 6 ft. from the appliance).
• Make sure the lid will fit over the box without interfering
with the finish material.
• The control box lid must be accessible and removable.
• Caulk around the perimeter of the box to prevent water
infiltration.
D. Electrical Codes
If the optional electrical kit is going to be used, the wiring
should be done at this time. See Section 6.A.
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA 70-
latest edition or the Canadian Electric Code CSA C22.1.
• A 110/120 VAC circuit for this product must be protected with
ground-fault circuit-interrupter protection, in compliance
with the applicable electrical codes.
• National electrical codes require a minimum of three
feet of space in front of the access panel for service
accessibility.
• The flex line and gas shutoff valve can be accessed
after installation by removing four screws from the valve
mounting bracket at the rear of the control box.
Note: The control box lid can be painted as desired.
Use sandpaper or other abrasive material to scuff
the surface prior to painting.
CUT CABLE TIE
CUT CABLE TIE
INCOMING GAS LINE
INCOMING GAS LINE

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 13
A. IntelliFire Plus™ Pilot Ignition System Wiring
• This appliance is equipped with an intermittent pilot ignition
(IPI) control which operates on a 6-volt system.
• This appliance is supplied with a battery pack which is
located in the control box. A wiring diagram is shown in
Figure 6.1.
• The battery pack requires four batteries (not included).
• An optional electric kit is available. This allows the system
to be operated with 110/120 VAC instead of batteries. See
Section 6.B.
• The appliance comes standard with an OFF/ON switch
on the control box lid
• Optional RC100 wireless wall switch (OFF/ON). For use
only with the optional electric kit.
• Optional RC200 wireless remote allows flame adjustment
(AUX200 is not required since there is no fan used). For
use only with the optional electric kit.
6
6 Electrical Information
Figure 6.1 Intermittent Pilot Ignition (IPI) Wiring Diagram - Battery Power Only
WARNING! Risk of Shock! Replace damaged wire with
type 105° C rated wire. Wire must have high temperature
insulation.
WARNING! Risk of Shock! Label all wires prior to discon-
nection when servicing controls. Wiring errors can cause
improper and dangerous operation. Verify proper operation
after servicing.
NOTICE: RC100 & RC200 must be protected from the
elements.
• The module should be in the REMOTE position. Putting
the switch in the OFF position will disable all fireplace
controls.
Hearth & Home Technologies recommends that IntelliFire
PlusTM wireless controls be used for their features and
functionality with the IntelliFire PlusTM ignition system.
External Control Switch
(Isolates batteries from system to increase battery life)
Valve
Module
Pilot
assembly
Wiring
harness
Jumper
wire
Battery
holder
RED RED
RED
BRN
BLK
BLK
GRN
ORG
ORG
WHT
RED
BLK


Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 14
B. Control Module Operation
1. The control module has an ON/OFF/REMOTE selector
switch that must be set. See Figure 6.1 and 6.2.
OFF Position: Appliance will ignore all power inputs and
will not respond to any commands from a wall switch or
remote. The unit should be in the OFF position during
installation, service, battery installation, fuel conversion,
and in the event that the control goes into LOCK-OUT
mode as a result of an error code. The external control
switch must be in the OFF position also.
ON Position: Appliance will ignite and run continuously
in the HI flame setting, with no adjustment in flame
output. This mode of operation is primarily used for
initial installation or power outage operation with battery
backup. The external control switch must be in the ON
position also.
REMOTE Position: Appliance will initiate commands from
an optional wired wall switch and/or one of the optional
wireless remote options. The external control switch
must be in the ON position also.
2. With the module in REMOTE mode, the flame output
can be adjusted with the HI/LO selector switch on the
module. See Figure 6.2. Note that the control module will
always ignite the fireplace on HI and remain so for the
initial 10 seconds of operation. If the HI/LO is switched to
the LO position, the flame output will automatically drop
to the lowest setting after the flame has been established
for 10 seconds. After this 10-second period, the flame
can be adjusted from HI to LO with the switch.
3. The control module has a safety feature that automatically
shuts down the fireplace after nine hours of continuous
operation without receiving a command from the wall
switch or optional remote.
4. The module has the capability to recognize potential
malfunctions. If these occur, it will fail to ignite and/or
respond to a command to ignite. If it fails to ignite, turn
off the external control switch and wait five seconds
and turn back on. If it fails to light the second time,
see Trouble Shooting guide. In this case, the module
may have gone into LOCK-OUT mode. In this state, it
will emit a RED/GREEN LED error code. To reset the
error code, switch the selector to OFF, and then back to
REMOTE or ON. If the ignition command again fails, the
module will emit an LED error code prior to going back
into LOCK-OUT mode. Contact your dealer for service
if this occurs.
NG/LP GAS-TYPE
SELECTOR SWITCH
SELECTOR
SWITCH
WIRE LEAD FROM REGULATOR CONNECTS HERE
MODULE
Figure 6.2 Control Module
Nine Hour Safety Shutdown Feature
The appliance has a safety feature that automatically
shuts down the fireplace after nine hours of continuous
operation without receiving a command from the wall
switch or optional remote.

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 15
C. Installing the Optional Electric Kit
• Remove four screws to remove cover from the control
box.
Figure 6.3 Remove Control Cover
Remove
2 screws
Junction
Box Bracket
Figure 6.4 Remove Junction Box Bracket & Two Screws
Figure 6.6 Hand-bend Bracket
Figure 6.7 Fasten Bracket to Junction Box
Match holes
Figure 6.8 Place & Fasten Junction Box
• Remove the junction box bracket by prying loose with a
screwdriver. Remove the two screws shown in Figure 6.4.
Cut out and remove insulation from behind junction box
bracket as shown in Figure 6.5.
• Make hand bends to bracket as shown in Figure 6.6:
• Fasten bracket to junction box with two screws (provided
with junction box).
• Thread wire into junction box.
• Place junction box into the control box, matching holes
as shown, and fasten with the two screws removed in
Figure 6.4.
Figure 6.5 Cut and Remove Insulation

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 16
LOAD
LINE/LIGNE
HOT
/TENSION
WHITE
/NEUTRE
HOT
/TENSION
WHITE
/NEUTRE
STRIP GUAGE
GABARIT DE DENUDAGE
O
T
/TENSI
O
HIT
E
/
NEU
T
H
T
O
W
Grounding connection
to box (if box has a
grounding terminal)
Wire
connector
Junction
box
LINE cable brings
power to the GFCI
Yellow sticker remains
in place to cover the
LOAD terminals
Figure 6.9 Wire the GFI Receptacle
• Wire the GFI receptacle as shown below:
• Assemble the junction box.
Figure 6.10 Assemble Junction Box
Figure 6.11 Replace Control Cover
• Disconnect the battery holder wires from the red and
black wires of the wiring harness from the switch and
module. Connect the red and black wires of the wiring
assembly included with the electric kit to the red and
black wires to the switch and module. Plug the power
supply wire into the wire assembly and then into the
outlet. See Figure 6.12.
• If installing optional remote control, disconnect the
brown module wire from the red jumper wire. See
Figure 6.12. Follow the instructions included with the
remote control.
• Replace the cover on the control box.

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 17
Figure 6.12 Intermittent Pilot Ignition (IPI) Wiring Diagram with Optional Electric Kit and Optional Remote Control
RC100 (optional)
External
Control
Switch
Valve
Module
Pilot
assembly
Wiring
harness
Red
Jumper
wire
Battery
holder
RED
RED
BRN
BLK
BLK
GRN
ORG
ORGWHT
Optional Electric Kit
Outlet box cover
Outdoor
GFI Outlet
Power
supply
Fuse
RC200 (optional)
If a remote is used, the brown module wire
must be disconnected from the red jumper wire.
BLK
RED
*
Optional Remote Control
*
Battery holder MUST be
removed to install the
optional electric kit.


Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 18
A. Mantel Projections
Figure 7.1 shows the dimensions for mantels or other com-
bustible projections above the fireplace opening.
Fireplace Structure
Noncombustible mat’l
Mantel
25 in.
(635 mm)
minimum
Ceiling or
Overhang
12 in. (305 mm)
max. combustible
mantel depth
Figure 7.1 Clearances to Mantels or other Combustibles above Appliance.
7
7 Finishing
WARNING! Risk of Fire! Comply with all minimum clear-
ances to combustibles as specified. Framing or finishing
material closer than the minimums listed must be construct-
ed entirely of noncombustible materials (i.e., steel studs,
concrete board, etc.).
B. Facing Material
The appliance can be covered with any noncombustible
material. Refer to Section 1.D.
It is possible for the face of the unit above the fireplace open-
ing to show signs of soot. Clean that area as frequently as
necessary to eliminate a build up of soot or permanent dis-
coloration. A noncombustible ledge (shelf) approximately 3
inches above the opening and a minimum of 3 inches out
from the face of the unit incorporated into the facing material
will help prevent the soot from going up the wall.
Note: The control box lid can be painted as desired.
Use sandpaper or other abrasive material to scuff
the surface prior to painting.

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 19
A. Clean the Appliance
Clean/vacuum any material that may have accumulated
inside the firebox.
8
8 Appliance Setup
E. Positioning the Logs
B. Optional Accessories
Install approved accessories per instructions included with
accessories. Contact your dealer for a list of approved ac-
cessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional accesso-
ries with this appliance. Using non-listed accessories could
result in a safety hazard and will void the warranty. Figure 8.2 Install Lava Rock
C. Pilot Shield
Ensure the pilot shield is still in the position shown in the
photo below. Shipping could cause it to become displaced.
Figure 8.1 Pilot Shield Position
D. Install Lava Rock
Pour lava rock into the burner pan and cover the burner tube.
DO NOT cover the burner tube from the right grate support
to the pilot assembly. See Figure 8.2 & 8.3. There is extra
rock provided to cover the front of the firebox if desired.
NOTICE! Do not cover area around pilot assembly with lava
rock. Too much rock will interfere with pilot flame ignition,
rectification, and wind stability.
Figure 8.3 Install Lava Rock
NO LAVA ROCK IN THIS AREA
NO LAVA ROCK IN THIS AREA
CAROLINA-36
• Place the rear log on the shelf against the appliance rear
wall. Position log as far back on the shelf as possible.
Figure 8.4 Place Rear Log - Carolina-36
PUSH LOG TO BACK OF SHELF
PILOT
SHIELD
HEAT
SHIELD
PILOT
BRACKET

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina • 4066-300 • Rev. Z • 11/13 20
• Place the top right log. There are flat indentations on the
rear and right front logs to locate the top right log.
Figure 8.7 Place Top Right Log - 36
• Place the top left log into the indentations on the rear and
left front logs.
Figure 8.8 Place Top Left Log - 36
• Place the fork of the center Y log above the middle front
grate bar and rest its back on the indentation in the middle
of the rear log.
Figure 8.9 Place Center Y Log - 36
Notch against grate
Figure 8.5 Place Left Front Log - 36
• Place the left front log on the grate against the front of the
grate. Fit notch in log to grate bar as shown below.
• Place the top center log as shown below.
Figure 8.10 Place Top Center Log -36
• Place the left and right center logs as shown in Figure
8.10
• Place right front log on the grate against the front of the
grate. Fit notches into the bottom of the log to position it
as shown in Figure 8.6
Figure 8.6 Place Right Front Log