Outdoor Lifestyles ODPLAZA-L24S User manual

1
Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
Outdoor Decorative Gas Appliance
This appliance is only for use with the type(s) of gas indicated
on the rating plate. This appliance is not convertible for use
with other gases, unless a certied kit is used.
NOT for use with solid wood fuel.
Model(s):
Installation Manual
Installation and Appliance Setup
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same area as
appliance.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other ammable
materials.
• Keep clothing, furniture, draperies and other ammable
materials away.
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
ODPLAZA-L24S
ODPLAZA-L24E
NOTICE: DO NOT discard this manual!
DANGER
FIRE OR EXPLOSION HAZARD
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. If odor continues, keep away from the
appliance and immediately call your gas
supplier or re department.
Failure to follow these instructions could re-
sult in re or explosion, which could cause
property damage, personal injury, or death.
WARNING
Do not store or use gasoline or other am-
mable vapors and liquids in the vicinity of
this or any other appliance
An LP-cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
WARNING: For outdoor use only.
Installation and service must be performed
by a qualied installer, service agency, or
the gas supplier.
Contact your dealer with questions on in-
stallation, operation, or service.

2Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
Propane Gas Cylinder Label
DANGER • FLAMMABLE GAS UNDER PRESSURE.
LEAKING LP-GAS MAY CAUSE A FIRE OR EXPLOSION IF IGNITED
CAUSING SERIOUS BODILY INJURY OR DEATH.
CONTACT LP GAS SUPPLIER FOR REPAIRS, OR DISPOSAL OF THIS
CYLINDER OR UNUSED LP-GAS.
WARNING • FOR OUTDOOR USE ONLY.*
DO NOT USE OR STORE CYLINDER IN A BUILDING,
GARAGE OR ENCLOSED AREA.
• Know the odor of LP-gas. If you hear, see or
smell leaking LP-gas, immediately get everyone
away from the cylinder and call the Fire Depart-
ment. Do not attempt repairs.
• Caution your LP-gas supplier to:
Be certain cylinder is purged of trapped air
prior to rst lling.
Be certain not to over ll the cylinder.
Be certain cylinder re-qualification date is
checked.
• LP-gas is heavier than air and may settle in low
places while dissipating.
• Contact with the liquid contents of cylinder will
cause freeze burns to the skin.
• Do not allow children to tamper or play with cyl-
inder.
• When not connected for use, keep cylinder valve
turned off. Self contained appliances shall be
limited to a cylinder of 30 lb. capacity or less.
• Do not use, store or transport cylinder where it
would be exposed to high temperatures. Relief
valve may open allowing a large amount of am-
mable gas to escape.
• When transporting, keep cylinder secured in an
upright position with cylinder valve turned off,
WARNING:
• Use only in compliance with applicable codes.
• Read and follow manufacturer’s instructions.
• Consult manufacturer’s instructions concerning
the cylinder connection provided with your appli-
ance.
• Be sure regulator vent is not pointing up.
• Turn off all valves on the appliance.
• Do not check for gas leaks with a match or open
ame. Apply soapy water at areas marked “x”.
Open cylinder valve. If bubble appears, close
valve and have LP-gas service person make
needed repairs. Also, check appliance valves and
connections to make sure they do not leak before
lighting appliance.
• Light appliance(s) following manufacturer’s in-
structions.
• When appliance is not in use, keep the cylinder
valve closed.
WHEN CONNECTING FOR USE:
Cylinder valve hand wheel
Point of connection
Liquid level indication
(optional)
Pressure relief valve
Cylinder
DO NOT REMOVE, DEFACE, OR OBLITERATE THIS LABEL
*EXCEPT AS AUTHORIZED BY ANSI/NFPA 58.
DANGER. Do not store a spare LP cylinder under or near a barbeque grill, or other heat sources.
NEVER ll an LP cylinder beyond 80% full: a re causing death or serious injury may occur.

3
Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Indicates practices which may cause damage to the appliance or to property.
Table of Contents
Propane Gas Cylinder Label 2
Installation Standard Work Checklist 4
1 Product Specic & Important Safety Information
A. Appliance Certication 5
B. BTU Specications 5
C. Non-Combustible Materials 5
D. Combustible Materials 5
E. California 5
2 Getting Started
A. Design and Installation Considerations 6
B. Inspect Appliance and Components 6
3 Framing and Clearances
A. Appliance Dimension Diagram 7
B. Clearances to Combustibles 8
C. Constructing the Appliance Enclosure 8
D. Propane Gas Enclosures Guidelines 9
4 Gas Information
A. Fuel Conversion 10
B. Gas Pressure 10
C. Gas Connection 10
D. Air Shutter Setting 10
5 Installation Instructions
A. Burner Pan Installation Instructions 11
B. Valve Bracket and Shutoff Valve Installation 12
C. Burner Extension Installation Instructions 12
6 Reference Materials
A. Accessories 13
B. Contact Information 14

4Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
Customer:
Lot/Address
Model: ODPLAZA-L24S
YES IF NO, WHY?
Hearth & Home Technologies recommends the following:
That this checklist remain visible at all times on the fire pit until the installation is complete.
ATTENTION INSTALLER:
Follow this Standard Work Checklist
This standard work checklist is to be used by the installer in conjuction with, not instead of, the instructions contained in this installation manual.
Date Installed:
Location of Appliance
Installer:
Dealer/Distributor Phone #
Serial #:
• Photographing the installation and copying this checklist for your file.
Appliance Setup
All packaging and protective materials removed.
Media installed correctly. (Reference Media Kit Instructions)
Manual bag and all of its contents are removed from the firepit and given to the party
responsible for use and operation.
Started appliance and verified no gas leaks exist.
WARNING! Risk of Fire or Explosion! Failure to install fire pit acording to these instructions can lead to a fire or
explosion.
Appliance Install
Required non-combustible enclosure materials installed (if applicable). (Pg. 8)
Verified clearances to combustibles. (Pg. 8)
Minimum ventilation requirements met (Pg. 9)
Comments communicated to party responsible
4079-312 • Rev B• 04/19
(Builder/Gen. Contractor) (Installer) (Date)
Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:
•
__________________________ by ______________________on _________

5
Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
C. Non-Combustible Materials
• Materials which will not ignite and burn, composed of
any combination of the following:
- Steel - Iron
- Brick - Tile
- Concrete - Slate
- Glass - Plasters
• Materials reported as passing ASTM E 136, Standard
Test Method for Behavior of Metals, in a Vertical Tube
Furnace at 750° C
D. Combustible Materials
• Materials made of or surfaced with any of the following
materials:
- Wood - Compressed paper
- Plant bers - Plastic
- Plywood/OSB - Sheet rock (drywall)
• Any material that can ignite and burn; ame proofed or
not, plastered or un-plastered
1 Product Specic & Important Safety Information
A. Appliance Certication
MODELS: ODPLAZA-L24S
LABORATORY: Underwriters Laboratories Inc. (UL)
TYPE: Outdoor Decorative Gas Appliance
STANDARD: ANSI Z21.97-2014 / CSA 2.41-2014
B. BTU Specications
Maximum allowable BTU ratings:
When an appliance is for connection to a xed piping
system, the installation must conform with local codes,
or in the absence of local codes with the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, or International Fuel
Gas Code.
Natural Gas Propane Gas
Burner
Pans Orice .089 #43 Orice .063 #52
132,000 32,000
2 65,000 65,000
3 100,000 100,000
4 124,000 124,000
5 147,000 147,000
E. California
WARNING: This product and the fuel
used to operate this product, and the prod-
ucts of combustion of such fuel, can ex-
pose you to chemicals including benzene,
which is known to the State of California to
cause cancer and reproductive harm. For
more information go to www.P65Warnings.
ca.gov.
WARNING: Improper installation, ad-
justment, alteration, service or maintenance
can cause injury or property damage. Read
the installation, operating and maintenance
instructions thoroughly before installing or
servicing this equipment.
NOTE: When using a 20 pound propane tank, it is
estimated that the burner will operate approximately 10
hours.
• Be sure to remove protective coating on stainless steel
surfaces.
This product is listed to ANSI standards for outdoor deco-
rative gas appliances.
Outdoor Lifestyles is a registered trademark of Hearth &
Home Technologies.

6Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
2 Getting Started
A. Design and Installation Considerations
Check building codes prior to installation.
• Installation MUST comply with local, regional,
state and national codes and regulations.
• Consult insurance carrier, local building, fire
ofcials or authorities having jurisdiction about
restrictions, installation inspection, and permits.
CAUTION
When planning an appliance installation, it’s necessary to
determine the following information before installing:
• Where the appliance is to be installed.
• Gas supply piping.
• Framing and nishing details.
Moisture Resistance
This outdoor gas appliance will shed moderate amounts of
water, but is not waterproof. Water and condensing water
vapor may enter the enclosure under certain conditions
Note: Take drainage into consideration when building
enclosure. Water MUST be able to drain away from the
enclosure.
B. Inspect Appliance and Components
• Remove the appliance and components from the
packaging and inspect for damage.
• Report any parts damaged in shipment to your dealer.
Parts included with the starter package:
- Pan Assembly
- (2) end caps
- Flexible bulk head with propane orice.
- (18) hex head screws
- (2) 1/2 in. NPT to 3/8 in. are adapter
- 1/2 in. decorative gas valve (incudes key and cover)
- Burner tube
- (3) burner tube brackets
- Flex line
- Valve bracket
- Natural orice
• Read all the instructions before starting the
installation. Follow these instructions carefully
during the installation to ensure maximum safety
and benet.
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, in-
complete or substitute components. Keep appliance dry.
Hearth & Home Technologies disclaims any responsibil-
ity for, and the warranty will be voided by, the following
actions:
• Installation and use of any damaged appliance.
• Modication of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the media.
• Installation and/or use of any component part not
approved by Hearth & Home Technologies.
Any such action may cause a re hazard.
WARNING! Risk of Fire or Explosion! DO NOT use this
appliance if any part has been under water. Call a qualied
service technician to inspect the appliance and to replace
any part of the gas control system which has been under
water.
The Plaza series gas appliance is designed for outdoor use
and may be installed as a stand alone unit or built against a
wall as long as it is non-combustible and comes to the edge
of the opening of the burner. Do not cover the top of burner.
Outdoor spaces - For the purpose of these instructions,
an appliance is considered to be outdoors if installed with
shelter no more inclusive than:
1. With walls on all sides, but no overhead cover
2. Within a partial enclosure which includes an overhead
cover and no more than two side walls. These side
walls may be parallel, as in a breezeway, or at right
angles to each other; or
3. Within a partial enclosure which includes an overhead
cover and three sidewalls, as long as 30% or more
of the horizontal periphery of the enclosure is perma-
nently open.
Note: Screen may be used on the open sides of the shel-
ter, 14x18 and 16x18 screen mesh is approved for use.
DO NOT use solar screen or no-see-um screen.

7
Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
3 Framing and Clearances
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only.
Figure 3.1 Appliance Dimensions
5-3/8 in
137 mm
2 in
51 mm
45° TYP
7-3/8 in
187 mm
A
B
5-3/8 in
137 mm
Air Shutter
Starter Kit Starter +1 extension Starter + 2 extensions Starter + 3 extensions Starter + 4 extensions
A 26 in (660 mm) 50 in (1270 mm) 74 in (1880 mm) 98 in (2489 mm) 122 in (3099 mm)
B 24 in (610 mm) 48 in (1219 mm) 72 in (1829 mm) 96 in (2438 mm) 120 in (3048 mm)

8Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
B. Clearances to Combustibles
When selecting a location for the appliance it is important
to consider the required clearances to walls (see Figure
3.2).
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be lo-
cated out of trafc and away from furniture and draperies.
NOTICE: Illustrations reect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.
Figure 3.2 Clearance to Combustibles
Minimum Enclosure Dimensions and Clearances to Combustible Surface
A
C
B
D
D
E
Minimum clearances to
combustible walls,
floor and ceiling
Appliance enclosure must be
made entirely of non-combustible
materials
A B C D E
ODPLAZA-L24S in 17 17 45 8 8
mm 432 432 1143 203 203
C. Constructing the Appliance Enclosure
Note: Take drainage into consideration when building
enclosure.
• The appliance enclosure must be made entirely of non-
combustible materials such as metal studs and cement
board.
• Minimum enclosure dimensions. See Figure 3.2.
• The gas valves must be located on the outside of
enclosure or in an optional box and easily accessible.
• Construction materials must be non-combustible if closer
than the minimum clearances shown in Figure 3.2.

9
Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
D. Propane Gas Enclosures Guidelines
1. Constructed and marked in accordance with the U.S.
Department of Transportation (D.O.T.) specications
for propane gas cylinders, spheres and tubes for
transportation of dangerous goods and commission,
CAN/CSA-B339, as applicable.
2. Provided with listed overlling device.
3. Provided with connection device compatible with
appliance.
• When constructing an enclosure to conceal a propane
tank cylinder, the enclosure must adhere to the following
construction requirements:
• Enclosure may be constructed with one side completely
open or if the enclosure is built with four sides, a top and
a bottom, then as follows:
- A propane gas cylinder enclosure requires four
ventilation openings at the top and bottom of the
enclosure (Figure 3.4). The openings must adhere to
the minimum requirements according to the capacity
of the cylinder. (Listed below)
- Each opening of the enclosure must be equally sized
and spaced a minimum of 90° apart (see Figure 3.4).
Openings must remain unobstructed.
- Top ventilation openings are required on the side
walls of the tank enclosure within five inches
(127 mm) of the top of the enclosure. They need to be
of equal size, unobstructed and spaced a minimum
of 90° apart. The openings need to be a total area
of 1 in2/lb (14.2 cm2/kg) of fuel storage capacity.
(Example: 1.0 in2 x 20 lb tank=20 in2)
- Bottom opening must provide a minimum of 1/2
square inch (7.1 cm2/kg ) for each pound of propane
contained in the tank. (Example: .05 in2 x 20 lb
tank=10 in2)
- Every opening must have minimum dimensions to
allow entrance of a 1/8 in. (3.18 mm) diameter rod.
- Ventilation openings in side walls must not
communicate directly with other enclosures of the
linear appliance.
- The cylinder valve must be easily accessible by hand.
Connections should be easy to leak test inside the
enclosure. A door on the enclosure is acceptable
only if easily opened without the use of tools and is
non-locking.
- The enclosure needs to isolate the cylinder from the
burner compartment and provide protection from
radiation, act as a ame barrier, and protect the
cylinder from foreign material.
- The enclosure needs to allow connection,
disconnection, and inspection of the connection of
the propane gas cylinder.
Opening shown at 180°
apart for reference only.
90° minimum.
2 in. min.
1 in. max.
5 in. max.
5 in. max.
Figure 3.4 Propane Cylinder Enclosure
- The enclosure should allow testing of any connection
on the propane cylinder that might be disturbed
during installation.
- Installation of ventilation as described above
is required on fixed piping installs (Natural and
Propane) in addition to propane cylinder enclosures.
- There is also a propane tank kit (LPTK-ODPLAZA-L)
available for the starter framing kit (FK-ODPLAZA-
24S) if a remote tank is not desired. Propane tank
kit is only to be used with a single 24 inch starter pan
and framing kit. The above ventilation requirements
are still required.
- If using a site constructed table, a frame may be built
to attach tank kit frame and must have a mechanism
to retain the cylinder to prevent tipping.
NOTE: The propane cylinder and regulator hose as-
sembly (not provided) must meet the following require-
ments stated in points 1, 2 & 3.

10 Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
A. Fuel Conversion
• Make sure the appliance is compatible with available
gas types.
• Conversions must be made by a qualified service
technician using Hearth & Home Technologies specied
and approved parts.
• To convert burner pan gas, change out orice in bulk
head and change air shutter setting. Propane orice is
installed from factory.
WARNING! Risk of Fire or Explosion! High pressure
will damage valve. Low pressure may cause explosion.
• Verify inlet pressures. Verify minimum pressures when
other household gas appliances are operating.
• Install regulator upstream of valve if line pressure is
greater than 1/2 psig (14 in. w.c.).
4 Gas Information
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
WARNING
When an appliance is for connection to a xed piping
system, the installation must conform with local codes,
or in the absence of local codes with the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, or International Fuel
Gas Code.
Gas Pressure Natural Gas Propane
Minimum inlet pressure 7.0 in. w.c. 11.0 in. w.c.
Maximum inlet pressure 10.0 in. w.c. 13.0 in. w.c.
Note: Have the gas supply line installed in accordance with
local codes, if any. If not, follow ANSI Z223.1. Installation
should be done by a qualied installer approved and/or
licensed as required by the locality. (In the Commonwealth
of Massachusetts, installation must be performed by a
licensed plumber or gas tter).
A listed (and Commonwealth of Massachusetts approved)
1/2 inch (13 mm) T-handle manual shut-off valve and ex-
ible gas connector are connected to the 1/2 inch (13 mm)
control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
C. Gas Connection
• Use approved 1/2 in. gas line to make connection to
valve and to create manifold for multiple sections.
• Pipe incoming gas line into enclosure.
• Connect incoming gas line to the 1/2 in. (13 mm)
connection on manual shutoff valve.
WARNING! Risk of Fire/Explosion! Support control
when attaching pipe to prevent bending gas line.
• A small amount of air will be in the gas supply lines.
WARNING! Risk of Fire/Explosion! Gas build-up during
line purge could ignite.
• Purge should be performed by a qualied technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks or
open ames.
• Light the appliance. It will take a short time for air to purge
from lines. When purging is complete the appliance will
light and operate normally.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all ttings and connections with a non-corrosive
commercially available leak-check solution. DO NOT use
open ame. Fittings and connections could have loos-
ened during shipping and handling.
D. Air Shutter Setting
Air shutter settings should be adjusted by a qualied service
technician at the time of installation. The air shutter is set
at the factory.
• Loosen the screw.
• Turn the air shutter counterclockwise for natural gas and
clockwise for Propane.
• Tighten the screw.
Air shutter settings:
• Natural Gas: Fully closed
• Propane: Fully open
B. Gas Pressure

11
Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
5 Installation Instructions
1. When choosing the location for your new linear burner
you must choose a location that adheres to clearance
to combustibles found in Figure 3.2.
2. Open starter kit and check to see that all components
in are included in the package.
3. Thread 1/2 in. NPT to 3/8 are adapter to shutoff valve
following the valve instructions provided with the shutoff
valve package.
4. Thread the 1/2" pipe coming from the gas supply to the
other side of the valve or thread 1/2 NPT to 3/8 are to
valve and ex line.
5. Attach bulk head and bracket to bottom of pan with hex
screws provided. See Figure 5.2.
Figure 5.1 Starter Kit (ODPLAZA-L24S)
Figure 5.2 Attach Flexible Bulk Head and Bracket to Pan
6. Attach exible gas line to the 1/2 to 3/8 adapter and
tighten with wrench, DO NOT apply sealant to are tting
side of adapter.
Note: If using additional burner pan extension kits see
Section 5C.
7. Install pan into enclosure and secure with high
temperature adhesive.
NOTE: Burner assembly can be installed on top of the
nish materials, or under the nishing materials. See
Figures 5.3 and 5.4.
NOTE: Be advised that if nishing materials are installed
on top of burner assembly, gas connections may not be
accessible for service unless access panels are built into
enclosure.
NOTE: Enclosure must be entirely of non-combustible
materials.
8. Be sure to check all gas line connections for leaks.
9. Fill pan to the top edge with optional media material (see
section 6A Accessories for available media).
Figure 5.3 Pan Installed on Top of Finish Material
Figure 5.4 Pan Installed Under Finish Material
1
2
34
56
7
Hand bends for valve
1 - Pan Assembly
2 - Flex line/orice
3 - Valve bracket
4 - Shutoff valve
5 - 1/2 to 3/8 ares
6 - Flex line
7 - Nat orice and screws
A. Burner Pan Start Kit Installation Instructions

12 Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
1. When connecting burner pans together, use the brackets
supplied with burner extension kit (ODPLAZA-L24E).
Each kit will allow installation of one extension. Up to
four burner extensions may be used.
2. When connecting a burner extension to a starter kit you
must create a manifold to supply gas to each extension.
Manifold can be made of 1/2 inch black iron pipe and will
need a pipe “T” and a drop for each additional burner
section. Manifold will need to be built to accommodate
quantity of burner extensions used.
3. Attach adapter 1/2 in. NPT to 3/8 in. are to the manifold.
Connect ex line to the 1/2 in. NPT 3/8 in. are adapter.
4. When installing multiple burner extensions, a separate
valve (VK-ODPLAZA) must be installed for everything
over 65,000 BTU of burner, (for example, a 10 ft. burner
would require (3) three separate valves, an 8 ft., (2) two
valves and a 4 ft.(1) one valve).
Figure 5.8 Extension Kit Brackets
1
2
3
4
5
6
Figure 5.7 Extension Kit (ODPLAZA-L24E)
C. Burner Extension Installation InstructionsB. Valve Bracket and Shutoff Valve
Installation
Valve bracket can be used when mounting the shutoff valve
or by itself or can be directly attached by screwing it to the
table in provided mounting holes. See Figure 5.5.
Shuto Valve
Valve Bracket
Figure 5.5 Valve Bracket
1 - Extension pan
2 - Screw pack
3 - Flexline bulkhead orice
4 - Extension brackets
5 - Nat orice
6 - Adapter 1/2 NPT to 3/8 are
Figure 5.6 Complete Burner Pan Starter Kit

13
Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
6 Reference Materials
A. Accessories
• Wind Shield Kit:
MEDIA - LAVA
MEDIA - COBALT
MEDIA - AMBER
MEDIA - BLACK
MEDIA - CRYSTAL
Lava Rock Glass Media
• LPTK-ODPLAZA-L Propane Tank Kit
(kit includes door, frame, tank restraint system and regulator)
• Media Material:
Glass Kit Order Chart
Number of
Sections WSPLAZA-L28S WSPLAZA-E24 WSPLAZA-E28 Total Dimension
1 1 0 0 28-1/2 x 10-1/4 in (724 x 260 mm)
2 1 0 1 56-1/2 x 10-1/4 in (1435 x 260 mm)
3 1 1 1 80-1/4 x 10-1/4 in (2038 x 260 mm)
41 2 1 104-1/2 x 10-1/4 in (2654 x 260 mm)
51 3 1 128-3/4 x 10-1/4 in (3270 x 260 mm)
• CVR-ODPLAZA 24 inch Burner Cover
• VK-ODPLAZA Valve Kit
• FK-ODPLAZA-L24S Framing Kit Starter
• FK-ODPLAZA-L24E Framing Kit Extension
Number of Burners 1 2 3 4 5
Additional VK-ODPLAZA
to order 0 0 1 1 2
Valve Kit Order Chart

14 Outdoor Lifestyles • ODPLAZA-L24S Installation Manual • 4079-311 • Rev B • 04/19
B. Contact Information
– NOTES –
Please contact your Outdoor Lifestyles dealer with any questions or concerns.
For the number of your nearest Outdoor Lifestyles dealer, please visit www.hearthnhome.com.
Hearth & Home Technologies
7571 215th Street West
Lakeville, MN 55044
www.hearthnhome.com
DO NOT DISCARD THIS MANUAL
CAUTION
• Important operating and
maintenance instructions
included.
• Leave this manual with
party responsible for
use and operation.
• Read, understand and follow
these instructions for safe
installation and operation.
Printed in U.S.A. - Copyright 2019
This product may be covered by one or more of the following patents: (United States) 5613487, 6006743, 6019099,
6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7074035, 7098269, 7258116, 7322819,
7470729, 7726300, 8147240, 9625149 or other U.S. and foreign patents pending.
2000-945D