Outdoor Router WRT4 U User manual

3G/4G OUTDOOR ROUTER
Instruction Manual
www.outdoorrouter.com
With an integrated mobile modem and Wi-Fi amplifier, the WRT4E outdoor router can receive 3G/4G mobile phone signals and
establish a Wi-Fi hotspot to connect your smartphone, computer, tablet, camera, TV box to the internet.
After inserting SIM card into build-in SIM card slot and connect the outdoor router to PoE injector, a Wi-Fi hotspot is instantly
established. The Wi-Fi output power is adjustable between 20/27/30dBm. WPA/WPA2 encryption standards ensure your wireless
connection is safe from intruders.
SKU: WRT4 E/U
Mobile tower
3G/4G
outdoor router
10-meter LAN cable 3-meter LAN cable
PoE
injector
Electrical
outlet
1. Introduction

2. Hardware overview
• 1 x 3G/4G outdoor router
•2 x Fiber reinforced plastic aerial
• 1 x 10-Meter LAN cable
Outdoor Router Aerials LAN Cables PoE Injector Cable Gland
Mounting Set & Tool
2 x Bracket 2 x Holder 2 x U-bolt 4 x Spring washer 4 x Washer 4 x Bolts 1 x Hex wrench
• 1 x 3-Meter LAN cable
• 1 x PoE injector
• 1 x Cable gland
• 1 x Mounting set and tool
2.1 Package contents
Left N-female connector
to 3G/4G mobile aerial
RJ45 socket to PoE injector via LAN cable
PoE power indicator
Router power indicator
Router power switch
Wi-Fi amplifier indicator
Right N-female connector
to 2.4G Wi-Fi aerial
Mobile signal indicator (Left)
Wi-Fi signal indicator (Right)
Micro SIM card slot
Reset button
2.2 Port, switch and indicator
Warnings
• Do not install with live electricity.
• Avoid your gas lines when grounding your wires.
• Tampering with your router will void your warranty.
PLEASE READ THE MANUAL AND FOLLOW THE STEPS CAREFULLY. THIS MANUAL WILL HELP YOU INSTALL THE
DEVICE PROPERLY AND AVOID IMPROPER USAGE. IF YOU NEED MORE INFORMATION ON, PLEASE CONTACT US.

3. Installation
3.1 Choose the outdoor location
3G/4G Signal reception
Using your mobile phone, walk around and look for a location that
gets a good signal. The suggested signal strength is at least 3 bars
(-90dBm).
If you have a weak signal reception, please upgrade the mobile
aerial with higher gain and directional logarithm aerial.
Distance to PoE injector
A 10-meter LAN cable is included. Make sure outdoor router is
no more than 10 meters away from the indoor PoE injector.
The 15V 1A PoE injector supports maximum 10-meter LAN cable.
If you want to extend to up to 50~100 meters, please contact us to
upgrade the PoE injector to 24V~48V.
Directional Wi-Fi coverage
The default Wi-Fi antenna transmit Wi-Fi signals to all the directions,
if you want to send the Wi-Fi signal to a defined area, and send the
Wi-Fi signal to a further distance, please upgrade the Wi-Fi aerial to
higher gain and directional logarithm aerial.
Wi-Fi AP mode
In the Wi-Fi AP mode, outdoor router could replay and boost the
Wi-Fi signal received from another router or access point (AP).
Make sure in the location of outdoor router could receive at least
2 bars of the Wi-Fi signals.
Mobile tower
Outdoor
router
Wi-Fi
signal
LAN cable to
PoE injector
3G/4G Router
Outdoor
router
Receive
Wi-Fi signal
Boost Wi-Fi
signal
LAN cable to
PoE injector
Wi-Fi Relay
Outdoor
router
Improve 3G/4G
signal reception
Send Wi-Fi signal to
further distance
Upgrade Aerials
2.3 Indicator description
PoE power
Router power
Mobile signal
Wi-Fi signal
Wi-Fi amplifier
Indicator Status Description
Red
Off
Red
Off
Blue
Blue flash slowly
Blue flash quickly
Off
Green
Green flashing
Off
Blue flashing
Off
System is up and ready
No input PoE power
PoE module and Wi-Fi module are turn on
Router is power off
Received 3G/4G signal, but cannot connect due to no SIM card or no money in SIM card.
Received 3G/4G signal, but no data transmission.
Received 3G/4G signal, transmitting data via the mobile network.
The 3G/4G signal has not been acquired.
Wi-Fi hotspot is working, no user connection.
Wi-Fi hotspot is working, and the user has connected.
Wi-Fi function has been closed.
Wi-Fi amplifier is working with 30dBm output power.
Wi-Fi function is off, or Wi-Fi output power is 17dBm or 20dBm.

3. Installation
3.2 Insert the micro SIM card
Use the hex wrench to lose 4pcs of hexagon bolts and open the
case.
Insert micro SIM/USIM card (12x15mm) into the SIM card slot.
See chapter 2.2 where is the “SIM card slot”.
Turn on router power switch. See chapter 2.2 where is the
“router power switch”.
Close the case and screw down the hexagon bolts with the hex
wrench.
The micro SIM card is not included in the package.
3.3 Install the aerials
The outdoor router uses 2pcs fiber reinforced plastic (FRP) aerials.
Install mobile phone aerial on the left N-female base connector,
and install another Wi-Fi aerial on the right base connector.
Twist the connector on aerial in clockwise direction to fix them on
the router.
3.4 Connect LAN cable to router
i. Take apart the cable gland, and through the LAN cable.
ii. Plug the RJ45 connector into RJ45 port in the base socket.
iii. Screw on the barrel screw on the base socket.
v. Insert rubber stopper into barrel screw, and crew down the cap.
Take off the cap then unscrew the barrel screw before disconnect
the LAN cable with the router.
3.5 Mounting set installation
3.5.1 L-shape bracket
i. Use the hex wrench to take off the clamp from the router.
ii. Install the L-shape brackets between the router and clamps.
iii. Use the hex wrench to tighten the hex bolts.
3.5.2 Install on a pole
i. Clasp the pole with U-bolts and holders.
ii. Attach the L-shape brackets (installed on the router) on the holders.
iii. Put spring washers, washers, and bolts on U-bolts then tighten
the bolts with a spanner (not included).
Base socket RJ45
Barrel
screw
Rubber
stopper
Cap
LAN cable
L-shape bracket
Clamp
Hex bolt
U-bolt Holder
Spring Washer
Washer
Bolt
Pole
L Bracket

3. Installation
4. Configuration
3.6 PoE injector
Connect another RJ45 connector on the 10-meter LAN cable to
PoE port on the PoE injector.
**Not required** Connect indoor router or computer to Lan port on
the PoE injector. A 3-meter LAN cable is included.
Use the power cord to connect PoE injector to the electrical outlet.
The green indicator on PoE injector will turn on after connected to
electrical outlet.
PoE Port
to outdoor router
PoE indicator
LAN Port
to indoor AP, router or computer
Power plug
to PoE injector power socket
Power plug
to electrical outlet
4.1 Connect to outdoor router
4.1.1 Wi-Fi / Ethernet connection
After connected to the electrical outlet, a Wi-Fi hotspot named “MIFI_xxxx” will be created within 20 seconds. The default
encryption type is “WPA2(AES)-PSK”, and the default Wi-Fi password is “1234567890”.
Connect to this hotspot on a computer, laptop or smartphone. You can also connect the router to your indoor Wi-Fi router or
computer via the 5-meter LAN cable.
PoE injector
4.1.2 TCP/IP setting
Configure TCP/IP on your connected devices, make sure IP address is within 192.168.100.101~200. The subnet mask should be
255.255.255.0. The router address should be 192.168.100.1.
If DHCP function is activated on your device, it will setup automatically. Otherwise, you need to configure IP manually.
On iPhone: Goes to Settings / Wi-Fi / Advanced
On Android phone: Goes to Settings / WLAN / Advanced
On Mac: Goes to System preferences / Network / Wi-Fi / Advanced / TCP/IP
On Windows: Goes to Start / Control panel / Network and internet / Change adapter setting (on left window panel) /
Local area connection / Properties (right click) / TCP/IPv4 (Internet protocol version 4) / Properties / General
Choose “Obtain an IP address automatically” and “Obtain DNS server address automatically”
Click “OK” to exit setting. Click “OK” again in the “Local area connection properties” to apply the new configuration.

4. Configuration
4.4 Advanced settings
4.4.1 Power-save
Choose Wi-Fi output powers from 10dbm, 20dBm and 30dBm.
4.4.2 Router
Setup IP address, Subnet mask, DHCP server, IP pool, and DHCP lease time of the outdoor router.
4.4.3 Firewall
Setup Port, filtering, Port mapping, Port forwarding, UPnP, and DMZ of the outdoor router.
4.4.4 Update
Upload and update the firmware of the outdoor router.
4.4.5 USSD
USSD is short of Unstructured Supplementary Service Data.
4.4.5 DDNS
DDNS is short of Dynamic Domain Name Server.
4.4.5 Others
Restart and reset the outdoor router.
4.2 Login your outdoor router
The default IP address of the outdoor router is 192.168.100.1 with subnet 255.255.255.0. Make sure your smartphone or computer
is connected to the router via Wi-Fi or LAN cable. Open a web browser and type http://192.168.100.1 in the URL address bar.
Use default password admin to login.
4.3 Interface overview
4.3.1 Status bar
From left to right, there are:
Network type, Operator, Signal strength, Wireless broadband connection, Cable broadband connection, SIM card, Number of users
4.3.2 Manu bar
SMS: Check received SMS messages, and send SMS message to other mobile phone numbers.
Phonebook: Check saved contacts, and add new phone numbers.
Advanced settings: See chapter 4.4.
Quick settings: The wizard will show you how to set up basic parameters of gateway safely.

4. Configuration
4.5 Network connections and status
4.6 Network settings
4.5.1 3G/4G connect status
On the left upper corner, you can quickly turn on / off the 3G/4G
mobile network connection and check the connection status including
upload speed, download speed, and working time.
There are six blocks below the menu bar on the front page.
4.6.1 Wireless broadband mode
Click “Wireless broadband mode” you can choose the broadband modes from
cable broadband, wireless broadband or automatic.
Click “Apply”, the outdoor router will apply new setting and rebot.
Suggest keeping the broadband mode stay in default “Wireless broadband mode”
or use “Automatic”.
Connection mode
Turn on/off auto connect to network function.
Network selection
Turn on/off auto search available network function.
Access point name (APN)
If your service provider provides a fixed APN, select Manual APN. Otherwise, please select Auto APN.
Virtual private network (VPN)
Connect to the VPN network with PPTP type.
4.5.2 Connected devices
Number of the devices connected to outdoor router, click the block and
check device name and MAC address.
You can block the unauthorized devices.
4.5.3 Data management
Help you to control the 3G/4G data usage wisely.
Click the orange color block and customize your data management
by time or by data.
4.5.4 Status information
On the right down corner, you can find the details of the router, including
IMEI number, IMSI number, Wi-Fi signal strength, and network name (SSID).
Click “Detail information” to view more information about the router.
The Wi-Fi encryption, SSID, and password are included in the bottom QR code.
4.6.2 Connection settings
Click “Network settings” to setup connection type.

4. Configuration
4.7 SMS control
You can control the outdoor router remotely by sending SMS messages to the phone number of inserted micro SIM/USIM card.
4.8 Reset factory settings
When the router is turned on, click and hold “Reset” button for 5 seconds until the router reboot. Or use the above SMS code *#06#.
*#01#
*#02#
*#03#
*#04#
*#05#
*#06#
*#07#,dialpref
*#07#,wifipref
*#08#,WRT4E,outdoorrouter,add
*#08#WRT4E,outdoorrouter,delete
SMS message Function
Turn on 3G/4G connection
Turn off 3G/4G connection
Turn on Wi-Fi hotspot
Turn off Wi-Fi hotspot
Reboot outdoor router
Reset outdoor router to factory settings
3G/4G connection at the first priority
Wi-Fi replay at the first priority
Connect to another Wi-Fi hotspot SSID “WRT4E” with password of “outdoorrouter”
Disconnect to Wi-Fi hotspot SSID “WRT4E” with password of “outdoorrouter”
4.6 Network settings
4.6.3 Wi-Fi settings
Click “Wi-Fi settings” to access the Wi-Fi configuration page.
Wi-Fi network name (SSID)
Setup SSID, hide SSID, wireless encryption type, Wi-Fi password, and max connection number.
Wi-Fi protected setup (WPS)
Enhance your Wi-Fi security with WPS by adding a PIN or push button configuration (PBC).
Advanced settings
Setup network standard, bandwidth, reign code, and frequency. The default is locked.
WLAN MAC Filter
Filter the MAC address by whitelist and blacklist to control the connected devices.
Internet Wi-Fi
Connect the outdoor router to Wi-Fi network.
The 3G/4G connection will turn off after connected.
Default setting is connected to Wi-Fi if added a Wi-Fi
Hotspot. You can change preferred network to “WWAN”
if want to connect to 3G/4G at the priority.
Add Wi-Fi Hotspot
Click “Add” below “Wi-Fi Hotspot” will start to search
available Wi-Fi networks.
Select from available Wi-Fi network list, input Wi-Fi
password, click “Apply”.
You can disconnect it from the “Wi-Fi hotspot” list.

Company:
Address:
Phone:
E-mail:
5. Troubleshooting
6. Contacts
5.3 No internet connection
In 3G/4G router mode
Login router control panel, check the mobile connection.
i. Make sure 3G/4G wireless connection is turned on. Refer to chapter 4.5.1.
ii. Check if the cellular signal reception is good. Refer to chapter 4.3.1.
iii. Check if the inserted SIM card has money.
In Wi-Fi relay mode
Check the internet connections ability of the relayed Wi-Fi network.
Make sure the IP address of Wi-Fi hotspot is not involved in the IP address pool of the outdoor router.
The default IP pool of router is 192.168.100.101~200. Check chapter 4.4.2 to change IP pool.
5.1 Can’t find Wi-Fi hotspot
Check the PoE injector
Make sure PoE injector is connected to the electrical outlet, the green indicator on PoE injector will turn on after connected to the
electrical outlet. The PoE power indicator on the outdoor router will turn on Red after have PoE power input to the router. If PoE
power indicator is off, check and ensure RJ45 connector on LAN cable connected to “PoE” port on the PoE injector.
Check the outdoor router
Make sure router power switch is in “ON” position. Router power indicator will turn on Red after turned on router power.
Check if Wi-Fi indicator is turned on. The Wi-Fi indicator will turn on Green after turned on the Wi-Fi function.
Remote control
Send SMS message *#03# to the phone number of inserted micro SIM/USIM card to turn on Wi-Fi function.
5.2 Forgotten password
If you have any question or suggestion about the outdoor router, please contact us.
Reset router login password
Default login password is “admin”. If you changed login password and forgotten it, please use one o below methods to reset the
outdoor router to factory settings.
i. Open the outdoor router case, click and hold the “Reset” button for 5 seconds until the router reboot.
ii. Send SMS message *#06# to the phone number of inserted micro SIM/USIM card.
Reset Wi-Fi password
You can set a new Wi-Fi password after login the outdoor router control panel. See chapter 4.6.3.
Shenzhen Easysmart Technology Co Ltd
Rm2906, Aoxinya Bldg, Caitian Road
Shenzhen, China 518033
0086 138 23371557
[e-mail]