Output Solutions KP-200 User manual

1. DIAGRAM FOR SET UP..................................................................1
2. INTRODUCTION..............................................................................1
3. POWER ON SEQUENCE.................................................................1
4. EDIT MODE OPERATION..............................................................2
5. PRINT MODE OPERATION.........................................................10
6. ERASE FORMAT............................................................................11
7. ERASE ALL FORMAT ...................................................................11
8. SPECIAL FEATURES OPERATION ............................................12
Appendix A. Pin Assignment ................................................................12
Appendix B. Font Expansions ..............................................................14

1
1. DIAGRAM FOR SET UP
2. INTRODUCTION
The KP-200 Stand-alone keyboard control Terminal supports four types of operation.
a. EDIT MODE OPERATION.
The operator can design or edit label formats by themselves. The label formats can be
stored in an interchangeable memory module. A maximum of eight formats may be
stored in each nterchangeable memory module.
b. PRINT MODE OPERATION.
Print the restored label format on the EZ-2 or EZ-4 Thermal Printer.
c. ERASE MODE OPERATION.
Delete an individual label format.
d. ERASE ALL MODE OPERATION.
Erase entire contents of interchangeable memory module.
3. POWER ON SEQUENCE
ConnecttheKP-200keyboardtothe EZ-2 or EZ-4 9 pin RS232 port with the interface
cable provided.
Power on the printer display show Product name and Version number. The LCD
display will show: GODEX
KP-200 VER 1.0
After approximately 2 seconds the LCD will change to display the four types of
operation. The LCD display will show:
[1] EDIT MODE
[2] PRINT MODE ?

2
There are four operation modes (as described in the introduction) that may be selected.
The keyboard operator can select the desired mode of operation by highlighting it with
the cursor keys and then pressing
ENTER” or
Press 1 to select EDIT MODE.
Press 2 to select PRINT MODE.
Press 3 to select ERASE FORM.
Press 4 to select ERASE ALL.
4. EDIT MODE OPERATION
Edit mode operation allows the keyboard operator to design new label format or edit
current ones.
Pressing 1or ENTER when Edit mode is highlighted will begin the Edit mode
sequence.
(A) RESTORE FORMAT FROM MEMORY MODULE.
If a label format has previously been saved in the memory module, the LCD display
will show:
RESTORE FORM(Y/N)
Enter N and the keyboard will automatically step to (B).
Enter Yand the LCD display will show:
ENTER FORM NAME:
LAB1
Let us assume thatLAB1 is the name of the first label format. You may use the cursor
keys to highlight previously formats of you may type in the format name if known.
Press ENTER and the keyboard will load the requested format from the memory
module. The LCD display will show:
WAIT FOR LOADING
>>.................................<<
(B) SELECT PRINTER TYPE.
The LCD display will show:
SELECT PRINTER TYPE.

3
2” PRINTER 4” PRINTER
You may use the cursor keys to highlight the desired printer type or you may key in 2 to
select the EZ-2 or 4 to select the EZ-4. Press ENTER to accept your selection.
(C) SELECT PAPER TYPE.
The LCD display will show:
SELECT PAPER TYPE:
Label , Blkmrk , Fax
Label -Self adhesive label with gap mounted on backing sheet.
Blkmrk -Registration mark on underside of media.
Fax -Continuous media with no registration mark.
Youmayusethecursorkeystohighlightthedesired media type of by typing in the first
letter of the required media (L. B. or F.). PressENTER to accept your selection.
(D) ENTER LABEL HEIGHT.
LCD display will show:
ENTER LABEL WIDTH
Enter label width in mm. PressENTER toacceptyourselection. If you selected Fax in
the previous menu, the keyboard will automatically step to (H), otherwise proceed to
next menu (E).
(E) ENTER LABEL HEIGHT.
LCD display will show:
ENTER LABEL HEIGHT
Enter label height in mm. PressENTER to accept your selection. If you selected label
at step (C), the keyboard will automatically step to (I), otherwise proceed with next
menu.
Note:Label height includes label length + gap.
Example: Labellengthis 25mm, Gap widthis3mm, then theLABEL HEIGHT will be
28mm
Label height in black mark label is defined as follows:
(a) The distance between tear line to next tear line.

4
l
e
b
e
l
h
e
i
g
h
t
(b) The distance Between Black mark (including itself).
lebelheight
(F) ENTER TOP LENGTH
LCD display will show:
ENTER TOP LENGTH
The TOP LENGTH is defined as follows: X will be the distance from the edge of the
black registration mark to the next tear line along the paper feed axis.
(1) IfXis less than 46mm, and the tear line is outside the black registration mark then
top length is X.
X
paperfeed
tearline
(2) If Tear line is inside Black registration mark then TOP LENGTH = -X.
paperfeed
tearline
x
(3)If Xis greater than 46mm, and the Tear line is outside the Black registration mark
then TOP LENGTH= Label height -X.

5
X
paperfeed
t
e
a
r
l
i
n
e
(G) ENTER BLACK LENGTH
The diagram of BLACK LENGTH is defined as follow: tearline
blacklength
The BLACK LENGTH in millimeters, then press “ENTER” key, KP-200 will go to
step(I).
(H) ENTER FEED LENGTH FOR FAX PAPER.
LCD display will show:
FEED LENGTH(1~25mm)
Enter Feed Length in mm and pressENTER to accept your selection.
(I) ENTER PRINT SPEED
LCD display will show:
SPEED 1 TO 2
2
Enter desired Print speed.
1is equal to 1“ per second.
2is equal to 2“ per second.
Press ENTER to accept your selection.
NOTE: 2“ per second is the default value.
(J) ENTER THERMAL HEAD
TEMPERATURE (DARKNESS)
LCD display will show:
DARKNESS 0 TO 7
5
Enter 0 to 7 (light to Dark), and press ENTER to accept your selection.
NOTE: Default value is 5.

6
(K) SELECT SELF STRIP FUNCTION.
LCD display will show:
SELF –STRIP (Y/N)?
N
If your printer has the stripper option, you can enter Yto enable the stripper sensor.
Press ENTER to accept your selection.
NOTE: Default value is N.
(L) FIELD PROGRAMMING.
LCD display will show:
FIELD 1:
The maximum number of fields available on one label format is eighteen. If the label
format has been restored form the memory module, you may usethe cursor keys to
select the field you wish to edit and then press ENTER. If this is to be a new label
format just press ENTER.
(M) ENTER DATA TYPE.
LCD display will show:
SELECT TEXT/BARCODE
[Shift]+[NUMERICAL]
Hold down the Shift key and press the 0 key to select the TEXT field.
Hold down the Shift key and press the 1 key to select the CODE 39 barcode field.
Hold down the Shift key and press the 2 key to select the CODE 93 barcode field.
Hold down the Shift key and press the 3 key to select the CODE 128 barcode field.
Hold down the Shift key and press the 4key to select the CODABAR barcode field.
Hold down the Shift key and press the 5key to select the INTERLEAVED 2 OF 5
barcode field.
Hold down the Shift key and press the 6 key to select the POSTNET barcode field.
Hold down the Shift key and press the 7 key to select the AN8 barcode field.
Hold down the Shift key and press the 8 key to select the EAN13 barcode field.
Hold down the Shift key and press the 9 key to select the UPC barcode field.

7
(N) ENTER BLANK LINE.
The LCD display will show:
LINE SPACE? (0~99 mm)
Line space is defined as the distance from this field to the next in mm. Enter desired
dimension (0~99mm) and pressENTER to accept your selection.
NOTE: Default value is 0.
(O) VARIABLE FIELD?
The LCD display will show:
VARIABLE (Y/N)?
Y
For variable data press Y. For fixed data press N.
NOTE: Default value is Y.
(P) FONT SIZE.
1. Horizontal multiplier. The LCD display will show:
ENTER X SIZE(1~4)
1
Enter horizontal multiplier (1~4). Press ENTER to accept your selection.
2. Vertical multiplier. The LCD display will show:
ENTER Y SIZE(1~7)
1
Enter vertical multiplier (1~7). Press ENTER to accept your selection.
NOTE: The default value in both case is 1.
3. Enter Text Data. The LCD display will show:
ENTER DATA :
_
Enter the Text data and press ENTER.
(Q) BARCODE DATA FIELD.
1. Narrow bar ratio. The LCD display will show:
NARROW (2 TO 4)
2
Enter narrow bar to width in dots.(2 to 4).
Press ENTER to accept your selection.
NOTE: The default value is 2.

8
2. Wide bar ratio. The LCD display will show:
WIDE(4 TO 12)
5
Enter wide bar width in dots(4 to 12) Press ENTER to accept your selection.
NOTE: The default value is 5.
3. Barcode height. The LCD display will show:
HEIGHT (1 TO 7)
3
Enter Barcode Height(1 to 7). Press ENTER to accept your selection.
NOTE: The default value is 3.
4. Human Readable. The LCD display will show:
READABLE(Y/N)
Y
Enter Y and human readable is enabled. Enter N and human readable is disabled.
Press ENTER to accept your selection.
NOTE: The default value is Y.
5. Enter Barcode. The LCD display will show:
ENTER DATA:
Enter the Barcode data and press ENTER to accept your selection. The keyboard
will automatically revert to menu K.
(R) SAVE FORMAT TO MEMORY CARD.
The LCD display will show:
SAVE FORM(Y/N)
Enter N-Keyboard will automatically step to next field.
Enter Y-LCD display will show:
Enter form name:
You can enter a maximum of sixteen characters to define a label name. Press
ENTER to save your format to the memory module.

9
(S) HOW TO SET UP DATA FIELD AS A VARIABLE.
1. If the data field is to be a variable, then the LCD display will show:
DATA LENGTH?(1~34)
A variable field allows the operator to input variable field data while the keyboard is in
the PRINT MODE enter DATA LENGTH(1~34, Dependent upon Font size & Label
width).
Press ENTER to accept your selection.
2. The LCD display will show:
ENTER X SIZE(1-4)
Same procedure as (P). Press ENTER to
accept your selection.
3. The LCD display will show:
ENTER Y SIZE(1-7)
Same procedure as (P). Press ENTER to accept your selection.
4. The LCD display will show:
POSITION OR PRESS D ?
Press “Shift”+“TAB1” Add one space in front of data.
Press “Shift”+“TAB2” Add eight spaces in front of data.
Press “&” This field and next field will be the same line.
Press “Shift”+“INS/L” To insert a field.
Press “Shift”+“DEL/L” To delete this field.
Press Dto step to next screen.
5. The LCD display will show:
POSITION OR PRESS D ?
•••••••
Theboxesdisplayed represent character fieldstoindicate to the operatorthelength(in
characters) of the variable data.
Example: Ifthedata length is5,LCD will show 5blocks.Ifthe data length is 3, LCD will
show 3 blocks. Press ENTER to proceed to next menu.