Outsunny 846-103V70 Installation guide

ASSEMBLY & INSTRUCTION MANUAL
INb1a019_UK
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
846-103V70

SAFETY INSTRUCTIONS
1
1. Read the instruction manual carefully before use and keep it for
future reference. Failure to comply with the instructions can result
in death, serious injury or property damage.
2. For outdoor use ONLY! Do not use indoors.
3. Do not use below ground level.
4. The accesible parts can get very hot. Keep small children, elderly
people and animals away from the gas grill. Grill glove is adviced.
5. Do not move the product while it is alight.
6. Turn off the gas supply at the gas cylinder when the grill is not in
use or after use.
7. Any modification of the product, misuse or failure to follow the
instructions may be dangerous and will void the warrenty.
8. Check your gas grill anually for leaks. Check whether the hose
connections are tight and leak test them each time you reconnect
the gas cylinder.
9. Do not use the gas grill within 1 meter of combustible materials
or surfaces.
10. LP gas cylinders should not be placed directly underneath the grill.
11. Open the hook of the grill before lighting.
12. Do not leave the grill unateended when it is lit.
13. Be careful when opening the hook, as the hot steam inside is
released upon opening.
14. Do not cover the grill untill it has completely cooled down.
15. Do not use aerosols near the grill.
16. Do not store or use petrol or other flammable vapours or liquids in
the vicinity of this gas grill or any other appliance.
17. If you smell gas, turn off the gas supply at the gas cylinder;
extinguish any open flame; open the hood. If still have it, stop use.

2
PART LIST
No. No.
Pic. Pic.
Qty Qty
1
2
3
4
5A
5B
5C
6A
6B
7
8
9
10
11
12
13
14
15
21
A
B
C
E
1
1
2
3
1
1
2
1
1
2
2
2
1
1
1
2
2
32
4
1
1
1
2
G
H
J
F2
2
2
1
22
23
2
1
M4 *8 screw
+2(spare)
M5*12 screw
Top door pin
Bottom door pin
M3*nut
M3*10 screw
M3*10 self-tap screw

3
Note: Please do not tight the screws and nuts till all assembly steps completed.
Assembly
1. Assemble the LH and RH frame plates (5C) to LH & RH
legs (5A, 5B, 6A & 6B) with 8pcs M5 screws (B).
M3*10 st x 2
M3 nut x 2
M3 * 10 screw x 2
22
22

4
Assembly
2. Assemble the LH and RH frame to bottom shelf (7)
with 4pcs M5 screws (B).

5
Assembly
3. Assemble the back shelf (9) to the frames with 4 pcs M5
screws (B).
9
B
B

6
Assembly
8
B
B
4. Assemble the front beam (8) to the front of frames with 4pcs
M5 screws (B).

7
Assembly
5. Assemble the 4pcs wheels (10&11) to the end of frame legs.
Note: the 2pcs wheels with break (10) are always in the same
side.

8
Assembly
6. The body (1) is slided into the frame legs with 8 pcs pre-assembled
M5 screws (See detailed pic.). Tight screws after body slided into
position.
Note: make sure the 8pcs screws are pre-assembled before sliding.
Thermometer (23) is fixed to the lid by its own screw.

9
Assembly
7. LH side shelf (14) is asssembled to the body with 6 pcs M5
screws (B).

10
Assembly
8. RH side shelf (15) is asssembled to the body with 6 pcs M5
screws (B).

11
Assembly
9. Handles (13) are assembled to front doors (12) with 4pcs
M4 screws (A). Totally 2 pcs doors.
A

12
Assembly
C
E
10. Doors are assembled to frames’ front legs with top and bottom
pins (C&E).

13
Assembly
11. Warming grid (2), cooking grids (3) and heat tents (4) are fixed
into the body.

14
Assembly
12. Oil cup (21) is assembled to the oil pan.

Tight all screws before use
Assembly completed
15
Assembly
J