OverskyRC Warlark-80 User manual

Warlark-80 Manual
The flight control board of Warlark-80 is based on F3 EVO hardware, supports both CleanFlight and
BetaFlight firmware. There are 3 kinds of hardware for its built-in compatible receiver: A---CYRF6936,
B---CC2500，C---A7105. There are 6 optional protocols for the built-in compatible receiver: 1=>DSMX/2; 2
=>DEVO (on testing); 3 =>Futaba SFHSS; 4=> FrSky (on testing); 5=> FlySky AFHDS; 6=>Hubsan(on
testing);
Warlark supports plug and play VTX-25MW analog video transmitter module or VTX-25MW &
OSD(WM OSD) module and analog camera.
Fetures:
1）F3 EVO flight control board
2) Optional built-in receiver
3) Diagonal motor to motor distance: 80mm
4) 7*16mm high KV brushed motors
5) 35mm ducted fan props
6) Working voltage: 3.7V(1S lipoly battery)
7) Flight weight: 39.4g (FPV with OSD version), 35.0g(No FPV version)
8) Flight time: 4 minutes (FPV with OSD version, 5 minutes (No FPV version)
9) No soldering for mounting VTX-25MW analog video transmitter module or VTX-25MW&OSD module
(note: the analog VTX is 40CH)
10) The working frequency of the VTX is controlled by transmitter
11) Supports parameter setting up through transmitter (only FPV with OSD version gets the function)
HOW TO ENTER flight control parameter setting up menu through OSD

According to the above picture: put THR stick to middle position, YAW to rightest, PIT to topmost,
and then enters FC parameter setting up mode. The following pictures are the setting up options:
Note: 1) For the explanation of each setting option, please check Cleanflight and BetaFlight manual

2) Please check MW OSD manual for OSD setting up
3) The background of the above picture is purpose-made
Binding operation:
There are two ways for binding operation: one is long press(2 seconds) the button and enters binding
mode; the other is time out binding.
The Flight control board with Futaba SFHSS compatible receiver and FrSky receiver belongs long
press binding mode.
Time out binding mode is for flight control board with DSMX/DSM2 , DEVO(on testing) and FlySky
AFHDS compatible receiver.
Note: LED A fast blinking indicates binding mode, solid bright LED A means binding success
Frequency checking and setting up on analog video transmitter (the operation way will be changed
according to feedback from customers)
6 LED lights on the board indicates the working frequency of the video transmitter in binary
calculation way, LED 1, LED 2, LED 3 represent 5 groups of frequency, LED A, LED B and LED C show 8
frequencies. When the board is powered, 6 LED lights flash 2 times indicates the present working frequency.
Pull the throttle to lowest, press the button slightly, you can check the current working frequency of the
VTX (LED lights flash twice); Push the throttle to mid range, double press the button and then enters
frequency set up mode; The LED light group shows the current working frequency when the VTX enters
frequency set up mode, push or pull Elevator stick up and down, you can change the frequency groups (5
groups), pull Aileron stick right or left, you can change frequency points (8 frequency points in total); After
finishing frequency set up, pull or push the throttle stick to highest or lowest position, frequency set up mode
quits and the frequency changes to the set up frequency which is save on VTX, LED group lights flashes
twice indicates the finished operation.
。
LED1
LED2
LED3
LEDA LEDB LEDC
000
001
010
011
100
101
110
111
0
0
0
5740M
5760M
5780M
5800M
5820M
5840M
5860M
5880M
0
0
1
5865M
5845M
5825M
5805M
5785M
5765M
5745M
5725M
0
1
0
5733M
5762M
5771M
5790M
5809M
5828M
5847M
5866M
0
1
1
5705M
5685M
5665M
5645M
5885M
5905M
5925M
5945M
1
0
0
5658M
5695M
5732M
5769M
5806M
5843M
2880M
5917M
注：0 --- LED_OFF，1 --- LED_ON.