Owon WSP406UK-2G User manual

WSP406UK-2G In-wall Smart Plug
Quick Start Guide

2
Welcome
1
The WSP406UK-2G ZigBee In-wall Smart Plug allows you to remotely
control your home appliances and set schedules to automate via mobile
phone. It also helps users to monitor the energy consumption remotely.
This guide will provide you with an overview of the product and help you
get through the initial setup.
Get to know your device
2
On/Off button & LED indicator

3
Get started
3
Warning!
• The in-wall smart plug must be installed and serviced only by qualified
electrical person.
• Do not touch the terminals of the device during the testing.
• Turn off all power supplying this equipment before installing.
• Make sure that the power supply is off before connecting or disconnecting
it to the auxiliary device.
On/Off button
Reset. Press and hold the On/Off button (Any one of the two) for ten seconds
until the LED indicator flashes three times to restore the smart plug to
default factory settings.
LED indicator
The LED status gives the following information:
LED status What it means
LED keep flashing Device has not joined a network.
Steady light Device has joined a network.
Flashing three times Return to Factory Settings.
Identify.
Green LED Device is on.
Red LED Device is off.
Identify. Press and hold the On/Off button (Left button control the left
socket, Right button control the right socket) for three seconds until the LED
indicator flashes three times.
On/Off. Press one time to switch On and Off (Left button control the left
socket, Right button control the right socket).

4
Failure to follow these instructions will result in death or serious injury.
A Gateway.
The mobile app.
In-wall Smart plug.
3.1 To get started, you will need
The in-wall smart plug must be installed by qualified electrical person, keep
the wiring diagram below for future reference. Cut off all power supplying
this equipment before installing.
3.2 Installation
Ground wire
Live wire
Neutral wire
Wiring Diagram
L
N
MADE IN CHINA
• Always use a properly rated voltage sensing device to confirm power is
off.
• Replace all devices, doors and covers before turning on power to this
equipment.

5
3.3 Connect to the gateway’s network
1. Set your gateway to permit joining.
2. Plug in the in-wall smart plug and the LED indicator will start flashing
(reset it if not).
3. The In-wall smart plug will join the gateway automatically and the LED
indicator will turn steady when successfully joined.
4. Now you can find the In-wall smart plug in the mobile app.
Note: Please make sure the max. load current of all the connected
appliances is no more than 15A (Two lines total).
4FAQ
Q 1. How to pairing WSP406UK-2G in-wall smart plug and SLC602 remote
switch?
1. Make sure that the in-wall smart plug and remote switch have joined in
the same gateway.
2. Press the On/Off button of in-wall smart plug for 3 second until LED flash
3 times then release. (when the smart plug enter pairing mode, LED will
start flashing. )
3. Press the reset button of remote switch for 3 seconds until LED flash 3
times then release to enter pairing mode.
4. Waiting the in-wall smart plug and remote switch pair automatically,
when the two devices are bonding successfully, LED of in-wall smart plug
will turn solid on, LED of remote switch will flash green light 3 times and
then light off.
Now you can use the remote switch to control the in-wall smart plug.
Remind:The operating steps are same as above when WSP406UK-2G in-wall
smart plug are pairing with SLC603 dimmer switch, RC204 remote control,
KF205 remote control.

6
Wireless Connectivity • ZigBee 2.4GHz IEEE 802.15.4
RF Characteristics
• Operating frequency: 2.4GHz
• Range outdoor:100m (Open area)
• Internal PCB Antenna
ZigBee profile • ZigBee HA profile
Operating Voltage • 100~250 VAC 50/60 Hz
Operating Power • Max Load Current: 220VAC 15A (Total)
• Standby : < 1 Watts
Calibrated Metering Accuracy • ≤ 100W (smaller than ±2W)
• >100W (smaller than ±2%)
Dimensions • 86 x 146 x 27 mm (L*W*H)
5Technical Specications
Q 2. How to clear the accumulative power consumption of the in-wall smart
plug?
Way 1：Login the relative gateway on your app, enter the edit mode (IOS:
Slid left the corresponding equip bar. Android: click the edit button ), then
click the clear accumulative power consumption button(arrow icon).
Way 2：Reset the in-wall smart plug to factory default setting. Note: This
way will lead the device lost connection of internet, you need to reconnect
the gateway internet to use it.

7
Safety Notice
WARNING: Failure to follow these safety notices could result in fire,
electric shock, other injuries, or damage to the In-wall smart plug and
other property. Read all the safety notices below before using the In-wall
smart plug.
6
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit yourself.
• Do not expose the unit or its accessories to flammable liquids, gases or
other explosives.
• Do not change the structure, safety, capability and design without
authorization.