Oypla 3053 User manual

Heavy Duty Gardening Trolley
User Manual
USER MANUAL Model No: 3053

•The sprayer is designed for the application of agricultural chemicals, disinfectants, cleaning agents
etc. Do not spray caustic or corrosive solutions as these will damage the sprayer.
•Wash the inside of the spray tank with clean water after usage.
•Always wear the correct personal protective equipment whilst using, cleaning and servicing the
sprayer.
•Lubricate the felt sealing washer at the top of the air chamber with light oil at regular intervals.
This ensures smooth operation of the air pump and prevents leakage of spray liquid.
•Do not expose the sprayer to strong sunlight when storing as to prevent deterioration of the tank.
•Store the 16 Litre Knapsack Sprayer in a well ventilated area, out of the reach of children and
animals.
•Always direct the spray downwind of the operator. Spraying into the wind will result in operator
contamination.
•Do not smoke whilst using the sprayer.
•If the product is damaged or has any defects, please contact [e-mail]
USER MANUAL Model No: 3053
•This product is not a toy, and is only to be used for its designated purpose.
•This product is intended for outdoor use only.
•Do not carry out alterations or modifications to this product.
•Clean only with a damp cloth. Do not use strong industrial cleaning substances.
•Leaving the product outside exposed to weather, especially direct sun, rain and
salt air, will speed the weathering process. This can be slowed by removing the
product from these conditions, or covering it with a suitable cover.
•Before using the product, make sure all the fastenings are tightly in place and
that everything is in order, and checked periodically by an adult.
•Do not overload the trolley.
•Ensure the load is evenly spread.
•Don’t turn too quickly as this may cause the load to become unsafe and fall out.
•Don’t pull the trolley off of curbs or other elevated places as this may damage
the load and/or the trolley. Use a ramp where possible.
•Do not fill the tires with too much air as this may cause for them to become
damaged due to the density.
•If the product is damaged or has any defects, please contact [email protected]
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold on
this condition, which no representative of the company can waive or change.

Parts List:
If you are missing any of the below parts please contact [email protected]
Please be aware that you will be referring to this parts list throughout the assembly process.
USER MANUAL Model No: 3053
Operating Instructions

USER MANUAL Model No: 3053

1. Place the handle beam (part 1) on top of the handle beam axle (part 2), ensuring that the handle beam (part 1) is as
far down as possible. This should leave a section of the handle beam axle (part 2) exposed. Slide the handle beam
washer (part 3) onto the exposed section of the handle beam axle (part 2). Secure these in place with a securing pin
(part 4). Please see the images above.
Part 2
Part 3
Part 1
Part 4
2. Slide the handle beam (part 1) onto the trolley platform (part 5) so that it aligns with either group of holes in the
bottom of the trolley platform (part 5). Once done, hold the handle beam (part 1) in place using a trolley support bolt
(part 6) and secure this in place with a support washer (part 7) and a support nut (part 8). Repeat for the other holes.
Please see the images below.
Part 6
Part 8
Part 1
Part 5
Part 7
3. Slide the rear axle (part 9) onto the other
set of holes. As with the handle beam, secure
these in place using the trolley support bolts
(part 6), support nuts (part 7) and support
washers (part 8). Repeat for the other holes.
Please see the image to the right.
Part 7
Part 8
Part 6
Part 9
USER MANUAL Model No: 3053

USER MANUAL Model No: 3053
4. Push a wheel (part 10) onto either the handle beam axle (part 2) or the rear axle (part 9), then slide a wheel washer
(part 11) onto either axle and secure both the wheel (part 10) and the wheel washer (part 11) into place with a securing
pin (part 4). Repeat this step on the opposite side and the remaining axle to complete the wheels. Please see the
images above.
Part 10
Part 2/9
Part 11
Part 4
5. Align the metal tube on the bottom of the platform
side panel (part 12) with the metal tube on the trolley
platform (part 5), securing this in place with a hitch
pin (part 13). Repeat this on the other side of the
platform side panel (part 12) to complete this side
and repeat this process on the opposite side of the
trolley platform (part 5) to complete both sides.
Please see the image to the right.
Part 12
Part 13
6. Align the metal tube on the bottom of the trolley
platform front panel (part 14) with the metal tube on
the trolley platform (part 5), securing this in place
with a hitch pin (part 13). Repeat this on the other
side of the platform front panel (part 14) to complete
this side and repeat on the opposite side of the
platform (part 5) to complete both sides. Please see
the image to the left.
Part 13
Part 14

7. Slide the handle (part 15) into the handle rotation pod (part 16), making sure the holes in both parts are aligned.
After this. Push the handle support bolt (part 17) through both parts, holding them into place. Secure these with a
support nut (part 7) and a support washer (part 8).
Part 17
Part 16
Part 15
Part 8
Part 7
Once completed, ensure that all the support nuts (part 8) are tightened so the parts are secure and won’t fall off over
time and that the securing pins (part 4) are all bent to ensure that the wheels won’t fall off when using the Heavy Duty
Garden Trolley. Make sure to pump the wheels (part 10) up before use so that when transporting heavy loads in the
Heavy Duty Garden Trolley the wheels don’t become worn at a faster rate. Do not over fill the wheels as this may cause
them to become too dense and more likely to burst.
USER MANUAL Model No: 3053

USER MANUAL Model No: 3053
Ensure fully assembled and secure before use.
Please retain a copy of all instructions for future consultation.