Oypla 4224 User manual

Rolling Garden
Seat
User Manual
USER MANUAL Model No: 4224

If at any time during activity you feel faint, dizzy or experience pain, stop and consult your physician
or doctor.
Make sure all fastenings are tightly in place and that everything is in order before using the product.
This should be checked periodically by an adult.
Unpacking, installing and fixing the parts are to be completed by an adult.
This product is not a toy, and is only to be used for its designated purpose.
Do not carry out alterations or modifications to this product.
This product is not suitable for use by children.
Clean only with a damp cloth. Do not use strong industrial cleaning substances.
Leaving the product outside exposed to weather, especially direct sun and rain, will speed the
weathering process. This can be slowed by removing the product from these conditions.
Never exceed the maximum load capacity of 150kg, or it may result in product failure and/or personal
injury.
Take care when sitting on the seat as it is able to rotate 360°.
Do not attempt to stand on the rolling garden seat.
Do not attempt to pick up the rolling garden seat if it has items loaded on it.
Pinch points can cause personal injury.
This product is not intended for use by persons (including children) with reduced physical, sensory
and mental capacities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the product by persons responsible for their safety.
Only use this product on stable and level ground.
Do not discard any of the packaging until you have checked that you have all of the parts and fitting
required.
Use the correct fixings as indicated. Do not tighten any of the nuts until the unit is completely
assembled, then finish by tightening all nuts. All nuts must be tightened before use.
It is suggested to use a screwdriver and spanner to help secure the nuts in place (screwdriver and
spanner not included).
Keep away from fire.
If the product is damaged or has any defects, please contact [email protected]
USER MANUAL Model No: 4224
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold on
this condition, which no representative of the company can waive or change.
USER MANUAL Model No: 4224

Small Screw
10pcs
Medium Screw
4pcs
Large Screw
1pcs
Small
Washer
11pcs
Medium
Washer
4pcs
Large
Washer
4pcs
Small Nut
11pcs
Medium Nut
4pcs
Large Nut
4pcs
Handle Support
1pcs
Handle
1pcs
Tray Bracket
1pcs
Axle
1pcs
Wheel
4pcs
Tray
1pcs
Steering Link Connector
1pcs
Basket
1pcs
Axle Sleeve
2pcs
Frame
1pcs
Seat
1pcs
Small Reinforcing Plate
3pcs
USER MANUAL Model No: 4224
Parts List:
If you are missing any of the below parts please contact [e-mail]

1. Place the steering link connector onto
the front axle section of the frame.
Secure the steering link connector by
putting a small screw through each end
hole (two) and add a small washer to the
other side of each screw and then a small
nut. This is shown below. Ensure that the
nuts are tightened. Insert the axle
through the rear axle frame.
2. Place the handle support over the front
axle. Secure this again but putting a small
screw through the front and back holes of the handle support and add
a small washer and nut onto the other side and tighten. Attach the
handle to the handle support by lining up the end of the handle inside
the handle support. Insert the large screw through the holes of the
handle support and the handle and securing the end with a small
washer and nut.
3. To attach the tray to the frame, place a reinforcing plate under the
front rim of the tray, ensuring that you line up the holes with the pre-
drilled holes in the front bracket that is on the front of the frame. Then
use two small screws, nuts and washers to
secure this in place. To secure the back rim of
the tray to the frame, again place a
reinforcing plate under the back rim of the
tray. You will then need to place the tray
bracket over the top of the frame and line
these holes up with the ones in the
reinforcing plate and the tray. Again, use a
small screw, nut and washer for each hole to
secure them into place.
USER MANUAL Model No: 4224

4. Attach the seat to the seat post which is located on the
top of the frame. Line up the holes in the seat and the
seat post and insert a medium screw through each of
the four holes in the top of the seat. Ensure that they
also go through the seat post holes and secure on the
underside with a medium washer and a medium nut on
each screw.
5. Slide one of the axle sleeves onto each end of the back
axle followed by a wheel, ensuring that the valve
stem of the wheel is facing outwards. Secure this by
putting a large washer and nut onto the end of the
axle. Repeat this for the other end of the axle. To
secure the wheels onto the front axle, slide a wheel
on either end of the axle and again secure using a
large washer and large nut on the end.
6. Attach the basket to the back of the frame by lining
up the holes in the basket with the frame and
putting a small screw through each hole. Secure this
with a small washer and nut each. Use the last small
reinforcing plate on the inside of the basket, and attach it
accordingly onto the frame.
7. Tighten all nuts and ensure that the rolling garden trolley is
secure before use.
USER MANUAL Model No: 4224