P. Graham Dunn POPPUF User manual

Includes:
A. Spinner Base (1)
B. Side Panel Connector (1)
C. Reinforcement Panels (2)
D. Side Panels (2)
E. Pegboards (2)
F. Topper (1)
G. Shelf (16)
H. 6” Hooks (16)
I. Cross Dowels (8)
J. Bolts (8)
K. Allen Wrench (1)
Notes:
- Two person assembly
- Suggested tool: Flat Head Screwdriver
INSTRUCTIONS: POPPUF
Puzzle Piece Floor Display
C
Spinner Base Side Panel Connector Reinforcement Panels Side Panels
Pegboards Topper Shelf
A
E
FG
D
H
6” Hooks
B
Cross Dowels
Bolts
I
J
19”W x 62”H
Allen Wrench
K

1. Stand one Side Panel (D) upside down
on floor.
2. Insert a Cross Dowel (I) into each circle
opening in the Side Panel Connector (B).
Assure the slits in the Cross Dowels (I)
are parallel with the Side Panel
Connector (B) openings, using a Flat
Head Screw Driver.
3. Place Side Panel Connector (B) upside
down aligning tabs on Side Panel
Connector (B) with slots on Side Panel
(D). From the side, place Bolts (J) in pre-
drilled holes, then use Allen Wrench (K)
to tighten.
4. Insert a Cross Dowel (I) into each circle
opening in the Reinforcement Panels (C).
Assure the slit in the Cross Dowel (I) is
parallel with the Reinforcement Panel
(C) openings using a Flat Head Screw
Driver.
5. Line up the Reinforcement Panel (C)
with the pre- drilled hole on the inside
of the Side Panel (D). From the side,
place Bolts (J) in pre- drilled holes then
use Allen Wrench (K) to tighten. Repeat
this for both Reinforcement Panels (C).
6. Repeat Steps 3-5 for second Side Panel
(D).
1
3
Note: Due to uneven top of Side Panel
(D) this will require two people.
Note: If assembled correctly, Bolts (J)
will interlock with Cross Dowels (I) for
stability.
22
4
5
2
33

7. Place Spinner Base (A), painted side
down, on top of Side Panels (F) by
aligning slots.
8. Rotate bottom of Spinner Base (A)
until pre-drilled holes are accessible.
Place Bolts (D) in pre-drilled holes,
then use Allen Wrench (E) to tighten.
9. Carefully turn display right side up
again.
10. Slide Pegboards (E) into the slots on
the Side Panels (D).
11. The Pegboards (E) should be level with
the tops of the Side Panels (D). If they
are not level, lightly tap or wiggle the
bottoms of the Pegboards (E) until
they slide into place.
12. Place Topper (F) on top of the Side
Panels (D).
11
12 12
6
Note: If assembled correctly, Bolts (D)
will interlock with Cross Dowels (C) for
stability.
Note: This may require two people to
flip.
7
8
7
11
910 10
Note: This should go on easily if
lined up with Pegboards (E) properly.
Note: The top of the Pegboard (E)
has the horizontal slots closest to
the edge. At first, decorative puzzle
tab at top may seem in the way.
Simply spread Side Panels (D)
slightly to access slots. Display may
need to be tilted for stores with
lower ceilings to slide into place.

10
13. Place Shelves (G) on Pegboards (E)
starting at the top vertical slot and
working down.)
14. Place 6” Hooks (H) on Side Panels
(D) starting at the top horizontal
slot and working down (skipping
second row and middle slots).
15. Congratulations! Display is ready to
load with product.
13 13
14
15

Puzzle Pieces
POPPUF-PUF8