Pacific Laser Systems PLS360E User manual

OPERATING
MANUAL
PACIFIC LASER
SYSTEMS
The Professional Standard
MADE IN USA
FEATURES
•BATTERY DOOR
•1/4 X 20 ACCESSORY MOUNT
BASE OF UNIT
•FIVE OPTIC WINDOWS
•USES THREE “D” 1.5V ALKALINE BATTERIES
• INCLUDES:
CARRYING CASE
WALL BRACKET
LASER DETECTOR (OPTIONAL)
PLS360E Laser Level •ON/OFF
SWITCH
•INDICATOR
LIGHT
PLS-LD LASER DETECTOR
FOR EXTERIOR APPLICATIONS.
Please review the PLS-LD Laser Detector
operating manual for use with PLS360E
exterior applications.
PLS360 SHOWN WITH OPTIONAL DETECTOR

SWITCH MENU
GREEN LIGHT: ON
RED LIGHT: EXCEEDS TILT
AMBER LIGHT: BATTERY LOW
SOLID LIGHT: INTERIOR
BLINKING LIGHT: EXTERIOR
This product is warranted by PLS ·Pacific Laser Systems to
the original purchaser to be free from defects in material and
workmanship under normal use for a period of one year from the
date of purchase. During the warranty period, and upon proof of
purchase, the product will be repaired or replaced (with the same
or similar model at our option), without charge for either parts or
labor, through PLS. The purchaser shall bear all shipping, packing
and insurance costs. Upon completion of the repair or replacement,
the unit will be returned to the customer, freight prepaid. The war-
ranty will not apply to this product if it has been misused, abused
or altered. Without limiting the foregoing, battery leakage, dents
or gouges to the plastic housing, broken optic windows, damage
to the switch/LED membrane are presumed to result from misuse
or abuse. Tampering with or removal of the caution or certification
labels voids this warranty.
Neither this warranty nor any other warranty, express or implied,
including implied warranties of merchantability, shall extend
beyond the warranty period. No responsibility is assumed for
any incidental or consequential damages. This warranty gives
you specific legal rights, and you may have other rights which
vary from state to state.
PLS •Pacific Laser Systems
2656 Bridgeway, Sausalito, CA 94965
1-800 601 4500 www.plslaser.com
U.S. PATENT PENDING
ON
INTERIOR (SOLID)
EXTERIOR (BLINKING)
ON
OFF
WARRANTY
TILT BATT
FIRST PUSH: INTERIOR
SECOND PUSH: EXTERIOR
THIRD PUSH: OFF
INDICATOR FUNCTIONS

CHECK LEVEL
SAFETY LABELING
CAUTION: USE OF CONTROLS, ADJUST-
MENTS OR PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
PLS360E complies with US FDA
standards, 21 CFR, Subchapter J.
These labels are attached to every
PLS laser. These are not to be
removed or defaced. Removing
/defacing labels voids warranty
AVOID EXPOSURE
LASER RADIATION
EMITTED FROM
THIS APERTURE
PLS360E COMPLIES WITH FDA PERFORMANCE STDS.
21 CFR, SUBCHAPTER J
SERIAL NUMBER:
MFG’D:
CAUTION: LASER RADIATION WHEN OPEN. DO NOT
STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS. PATENT PENDING
REG. US PATENT OFFICE
PLS 2656 BRIDGEWAY, SAUSALITO, CA 94965
CAUTION
LASER RADIATION
DO NOT STARE INTO BEAM OR VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS
MAX OUTPUT POWER <1mW
WAVELENGTH 635-670nm
CLASS 2 LASER PRODUCT
WARNING LABEL
BOTTOM VIEW
TOP VIEW
APERTURE LABEL
ID# CERTIFICATION LABEL
We recommend that you check your PLS360E periodically in order
to assure its accuracy.
TO CHECK LEVEL: Choose two walls approximately 25’ - 50’ apart
(illustration below). You can use 2x4s for targets.
Turn on the PLS360E. With the PLS360E six inches away from
and facing target #1, carefully mark the center of the line. Label
this mark A1. Mark the center of the line on target #2. Label this
mark B1.
Move the PLS360E six inches away from target #2. Carefully mark
the center of the line. Label this mark B2. Mark the center of the line
on target #1. Label this mark A2.
Now measure the distance between A1 and A2, B1 and B2. If the
distances are the same, the laser is in calibration. If the difference
between the two sets of marks is greater than 1/16” @ 25’, or 1/8”
@ 50’, the laser is out of calibration.
It is also necessary to check each of the five beams for level. Place
the PLS360E at least 25’ away from a “target” wall. Position the laser
so that the window facing the target wall is parallel with the
target wall. Mark the center of the laser line. Rotate the laser so that
each of the remaining four windows is parallel with the target wall.
Each laser line should be within 1/32” of your initial mark at 25’.
Target #1 Target #2
A1
+
A2
B1
+
B2
-
25’-50’
WALL

SPECIFICATIONS
SPECIFICATIONS
Light source: Semiconductor laser diode
630-650 nM, visible
Working range: +/- 200 feet
Accuracy: <1/8”@ 100 feet
(<3mm @ 30 meters)
Leveling: Automatic
Leveling range: +/- 8o
Power supply: 3 “D”batteries
alkaline
Operating time: +35 hours continuous
Operating temp: 0o F to 120oF
(-18o C to 49oC)
Storage temp: 0oF to 120o F
(-18o C to 49oC)
Indicator: Green light: ON
Red light: EXCEEDS TILT
Amber light: BATTERY LOW
Solid Light: INTERIOR
Blinking Light: EXTERIOR
Environment: Water resistant; not submersible
Dimensions: 5”x 4-5/8”x 3-3/4”
Weight: 1lb. 15oz.(including batteries)
PLS Lab Technicians
PACIFIC LASER
SYSTEMS
The Professional Standard
PLS IS A REGISTERED TRADEMARK OF
PLS •PACIFIC LASER SYSTEMS