Pacific Sun CalcFeeder PRO User manual

CalcFeeder PRO
Controller for Calcium reactor
with stepper motor feeding pump
User Manual
ver. 2.0
www.Pacific-Sun.eu

Page 2
CalcFeeder PRO Calcium Reactor
Table of Contents
1. Introduction .........................................................................................3
2. CalcFeeder PRO Controller .................................................................4
Controller Touch-Screen Operations ............................................................................5
Controller Maintenance..................................................................................................6

Page 3
CalcFeeder PRO Calcium Reactor
1. Introduction
Dear Customer,
Thank you for purchasing the Pacific Sun CalcFeeder PRO Controller.
With the purchase of this unit, you have selected a top quality product. It has been
specifically designed for aquaristic purposes and has been tested by experts. With this
unit, you are able to adjust the calcium level as well as the carbonate hardness in your
seawater tank simply and efficiently in order to achieve optimum levels.
For best results, please read through this instruction manual before installing the reactor
on your system.
During or after installation, please do not hesitate to contact our technical support team
at [e-mail] if you have any questions about your new Controller.

Page 4
CalcFeeder PRO Calcium Reactor
2. CalcFeeder PRO Controller
Power
SupplyUSB Port
Solenoid Valve Port
Optical Sensor Port
Water Output
TO
Reactor
Water Input
FROM
Aquarium
LCD Touch Screen Step Motor Pump

Page 5
CalcFeeder PRO Calcium Reactor
Main screen
Decreasing flow effluent button.
Increasing flow effluent button.
Dosing pump “Pause” button.
“Settings menu” button.
Optical sensor status indicator.
Solenoid valve status indicator.
Current controller status working mode indicator.
Controller unit was designed to work with CalcFeeder PRO calcium reactor but can be
used also as a very precise feeding pump for any other Calcium Reactor brand (require
turning the “Standalone” mode to ON).
The CalcFeeder PRO controller is equipped with ultra-precise Stepper Motor pump with
four rollers. Built-in LCD touch-screen allows for very easy flow adjustments and controller
operations. The Controller firmware updates can be performed by internal USB port.
Controller Touch-Screen Operations
Settings menu
Reset controller button.
ON/OFF automatic “Degassing” button.
Automatic “Degassing menu” settings button.
ON/OFF automatic “Alarm CO” tank button.
ON/OFF “Standalone” working mode button
(when turn ON pump is running without
connected optical sensor).
Reactor water refills manual mode enable
button.
Degass Menu
Manual enable degassing button.
Degassing setting once per week.
Degassing setting twice per week.
Degassing setting every day.
Degass Menu Exit button.
5
1 2 3
6
74
5
6
41
2
3
4
31
2
5
1
2
3
4
5
6
7
1
2
3
4
5
6
1
2
3
4
5

Page 6
CalcFeeder PRO Calcium Reactor
Manual degassing screen
The controller pump work cycles are counted in
the upper left corner. The degassing process takes
200 cycles.
Reactor manual water refills screen
In order to Turn OFF the refilling process, press
and hold the „Turn off refill mode” button for 3
seconds.
Pump cycles
Stepper Motor Pump Cover
Pharmed BPT tubing
Controller Maintenance
Stepper motor allows for heavy duty work 24/7 without any limits. The controller allows
to set the rate at which calcium and carbonate are dosed in the tank from 100 ml/h to
7200 ml/h.
Please remember about regular tubing inspections and maintenance. Used Pharmed
BPT tubing has a MTBF (mean time before failure) of average 2000 hours and needs to
be replaced after that time. Regular lubrications by using silicone grease will extend tubing
lifespan and protect device against leaking and damage.
Stepper Motor Pump Cover

Copyright
Pacific Sun Sp. Z o.o.
I Brygady Pancernej WP 10
84-200 Wejherowo
Poland
tel. + 48 58 778 17 17
email: [e-mail]
If you need technical support - please contact with [e-mail]