Pacific Sun Metis Hyperion S User manual

Pacific Sun
Metis Hyperion S/S2
Pandora Hyperion S/S2
Triton S
9channel LED aquarium lamp with SMT matrix
Pacific Sun Hyperion S/Triton S lamps – manua

1 Table of Contents
Contents
1 TABLE OF CONTENTS ....................................................................................................................................................... 2
1.a General .................................................................................................................................................................... 3
1.b Firmware up ate ..................................................................................................................................................... 3
1.1 Initial start ............................................................................................................................................................... 6
1.2 Daylight settings ........................................................................................................................................................ 8
1.3 Colour settings .......................................................................................................................................................... 10
1.4 PAR Table …................................................................................................................................................................ 11
1.5 Moonlight settings ..................................................................................................................................................... 13
1.6 Custom scenario ........................................................................................................................................................ 14
1.7 Service tab ................................................................................................................................................................. 16
Pacific Sun Hyperion S/Triton S lamps – manua

1.a
Connecting to your computer
Pacific Sun lamps are controlle using a Bluetooth connection between oser an your computer. It is highly recommen e that you
use an external Bluetooth a apter to ensure a strong signal between the oser an your computer. Bluetooth a apter shoul be USB
compatible with Class 1 specification an output power not less than 14 Bm-20 Bm.
Steps:
1) Enable Bluetooth on your computer (or install external USB Bluetooth a apter)
2) Initiate the Pairing process between your oser an your computer
Tip! You can o this by going to your Start menu, an selecting Devices and Printers. Once the win ow
opens, click on Add a device button. Your computer will search for all available evices, an will show the
available Pacific Sun evices. Select your oser an click on Next.
3) Select option “Enter the devices pairing code”, enter “12 4” as the pairing co e, an click on Next. You will receive a
message stating “This evice has been successfully a e to this computer”.
Tip! All Pacific Sun evices have the efault pairing co e of “1234”.
4) You will see the lamp in your “Device list” now.
Tip! You can view your Device list by navigating to your Start menu, an selecting Devices and Printers.
Right click on the iscovere lamp an click on Properties
5) Click on the Services tab, an take note of the COM port that was assigne to your oser
Tip! You can increase the transfer rate between your lamp an your computer by clicking on the Hardware tab, selecting
your COM port, an clicking on Properties. In the new ialog, click on the Port Settings tab, an change the value of “Bits
per secon ” fiel to 19,200. Click OK an then OK again.
Using the software
Installation
From CD
1) Insert the CD into your CD-ROM rive
2) Go to My Computer or Computer, an ouble click on Pacific Sun CD to explore the contents of the isk
3) Double click on Setup.exe an follow the prompts on screen
From Web
1) Downloa the software
2) Extract the files to a local fol er using the RAR Lab WinRAR unpacking tool
3) Browse through the extracte files, locate Setup.exe an run it
Tip! You can also run the software by browsing through the installation isk / extracte fol er, an ouble clicking on the Pacific Sun
application.
Starting the software
The installation creates a shortcut to Pacific Sun software in your Start menu. Click on Start, an run the Pacific Sun software from
there.
Connecting to your doser
To control your lamp, you will nee to connect it to your computer first. (see Connecting to your computer for further help with this)
1) Start the software
2) Select the COM port for your lamp from the rop own, select Bluetooth in the secon rop own, an click on Connect
Tip! You can also type the COM port in manually in the rop own
Tip! Refer to Connecting to your computer to fin the COM port for your lamp
3) If software is unable to connect to oser at first, try a couple more times – you can also try moving closer to the oser for
better signal between the oser an your computer
Once the connection is successfully establishe , the software will isplay some basic information regar ing your actual oser
settings. Information isplaye varies in ifferent versions of software.
General information about Pacific Sun lamps firmware upgrade procedure
Caution: Switching off the power supply uring up ating process may amage your lamp CPU. Recomen e istance between the
lamp n the computer that you are using to up ate firmware is between 1-2 meters. If you are using a laptop with bluetooth mo ule
built-in, please use an external USB bluetooth mo ule for better signal strenght.
Bluetooth mo ule Class 1 is strongly recomen e .
Pacific Sun Hyperion S/Triton S lamps – manua

Uploading wrong firmware may damage your firmware and void your warranty. The amage may require returning the oser to
our service epartment to restore its original functionality. If you nee more a vance support please contact with our
[e-mail] irectly.
1. b
Firmware update process:
Downloa the application an firmware on to the computer that you will be using to up ate your lamp firmware. If you alrea y have
the Pacific Sun software installe on your computer – uninstall it an ownloa the newest version available on www.pacific-sun.eu
If you nee technical support, email [email protected] for further help.
Bluetooth protocol:
Check on which COM port your loser is installe . You can check this via Navigation Panel ( in Winows) – Bluetooth Manager – COM
ports. During pairing procedure please use code „12 4”.
Select the appropriate COM port – an click Connect button.
Click Connect to the lamp button.
Within a few secon s your computer shoul establish connection with your lamp ( you will see „Transmission Status Connecte ”in the
Status win ow.)
Next, select the System tab
Pacific Sun Hyperion S/Triton S lamps – manua

Click Firmware Upgra e – an select the firmware for your type of lamp ( firmware file extension is .bin).
Your lamp’s firmware is being up ate . When the process is complete , you will see „Firmware up ate ” isplaye in the status
win ow.
If the error occurs during transmission of the CRC and the firmware will not load properly - lamp will go to safe mode.
The screen appears:
Memory Erase . Uploa firmware.
This means that the transmission process is not finishe successfully.
To restore full functionality of the lamp you must perform the following steps:
a) Re uce the istance between the lamp an the computer to an absolute minimum - or use an external BlueTooth mo ule.
b) restart the lamp by isconnecting it for a few secon s after the voltage
c) re-run the application, select the correct COM port ( o not press on Connect to the lamp!)
) go to the Service Tab - click Firmware upgra e - an then select the correct firmware for your lamp
At this point, the firmware up ate process shoul start - the status bar will show the current progress up ate.
If you nee a itional information - please contact our service:
[e-mail]
Pacific Sun Hyperion S/Triton S lamps – manua

1.1 Initial start
Set your local ate an time in the Date/time settings fiel s.
Select your lamp mo el in the Software initialization fiel an confirm your selection clicking Save Settings button.
Week-Tweek
Very often it happens that at the weeken we have the ability (an willingness) longer sit watching our aquarium .. However, it also
often happens that in the late evening, when social life in our house is just beginning, the light in the aquarium "fa es" an the only
view we can enjoy the moonlight. To enable the "extension" - or "offset" the time of the lamp at the weeken for a few hours ahea - it
was written-Tweak Week program. How oes it work?
Let's take an example: "stan ar " we have set the lamp on the east si e at 10 am an the west (the start time of sunset) at 18:00.
Time of sunrise / sunset set to 2 hours. So - at 20.00 en s in " ay". If you want to watch the Satur ay an Sun ay, not expan e our
aquarium of light - is set for those ays Time Shift for example, (-3).
This means that for a tube that, in those ays, the time is "with rawn" for 3 hours. So - if you've east began at 10 - so now the light
"thinks" that it is 7 am an the actual east starts at 13:00 (real time) an sunset at 21:00 an runs until 23:00 …
Next so the " ay" lasts the same - but "slightly" later it starte .. Mon ay everything is back to "normal" - an we have the
opportunity to enjoy a weeken in our aquarium simply "more" ...
Light Intensity in Manual Override mode – here you can check an select the intensity of light your lamp will emit while operating in
the Manual Overri e mo e.
Acclimatization program
Specifically implemente acclimatization program - use to acclimate corals to LED lighting. Base on user- efine existing lighting
computer automatically selects the initial power output an color of light from the lamp, an the interval, which is change every ay
Pacific Sun Hyperion S/Triton S lamps – manua

lamp power, allowing corals in a gra ual get use to new sources of light (as amen e by the spectrum of light) an to its intensity.
The computer controls the power an change the color of light in the range from 15 to almost 90 ays (range automatic - epen ing
on the acclimation). This option eliminates the situation of "overexposure" aquarium an coral bleaching, which is a very common
symptom in the transition from other type of lighting(t5/hqi) to LEDs . At the en of the acclimation program automatically switches
off an the lamp goes to the mo e previously set, such as Basic Mo e or Par Table.
1.2 Daylight settings
Here you can configue basic settings for your lamp.
Sunrise start time – the beginning of sunrise simulation
Sunset start time – the beginning of sunset simulation
Duration – uration of sunrise/sunset
Max. lamp power – maximum power (between the en of sunrise simulation an the beginning of sunset simulation)
Smooth light transitions – efines how fast changes occur in the color of light in the performance of in ivi ual lines PAR table.
Enabling this option will result in a smooth transition between colors without su en jumps.
T5 lighting - This option is available only for lamps with T5 lighting(Pan ora Hyperion R2) . You can select the T5 lighting switch on/off
time
Pacific Sun Hyperion S/Triton S lamps – manua

1. Colour settings
A setting powers of each channel can attempt to recreate such as the spectrum of light emitte by fluorescent T5 favorite sets.
Probe colour – loa actual lamp settings
Set colour – save spectrum settings to lamp memory
Pacific Sun Hyperion S/Triton S lamps – manua

1.4 PAR table
Advanced simulation of day light.
With Linear PAR simulation option switche on – your lamp will gra ually switch from Basic light settings to more a vance
simulations selecte in the PAR table(without short flash between mo e changing).
First, set the hours of sunset/sunrise in Daylight tab.
A justing the in ivi ual parameters in PAR table, you can influence the intensity an colour of light for multiple time-perio s.
For example:
Select the uration of sunrise from 10.00 a.m. to 10.30 a.m. in the first row of the PAR table. Next, a just the intensity of selecte
light colours e.g. White 6%, Blue 1 10%, Orange 75% etc.
Click Update Row buton an the table settings will be up ate (selecte Row)
Next, select subsequent time-perio in the secon row of the PAR table, e.g. from 10.30 to 11.45 an a just light intensity for this
perio e.g. White 10%, Blue 10% an click Up ate to save your settings.
This feature allows you to a just colour temperature in various time-perio s – you can simulate „warm” sunrise (a justing only White
colour an a ing some re s/orange) an „col ” sunset (a justing Blue colour with violet).
Table PAR is quite powerful tool to create your own lighting programs: you have the ability to set in epen ent power for each channel
at ifferent times of the ay (an night). In a ition, you can generate a graph showing changes in light intensity for each channel
uring the ay. To set the color of light in a "live" - use "Colour Stu io Live", by which we you able to "live" watch how it will look like a
light in each time interval an mo ify them as nee e an recognition. An then you can up ate the recor in a table. This soun s
quite complicate - but really - in fact within a few minutes you will be able to o this is automatically. Especially that the application
itself fills the necessary fiel s in the table as the start time for the next "recor " in the table, etc.
Pacific Sun Hyperion S/Triton S lamps – manua

1.5 Moonlight settings
To set night light an moonlight simulation.
Basic settings
Moonlight intensity % - to set moonlight intensity (with maximum intensity for full moon)
Date of the last full moon – to set the ate of the last full moon. The preset ate is 2011-09-12( ate of the actual full moon)
Moon cycle simulation – to swich on/off moonlight simulation
With moonlight simulation switche off – you will get constant, invariable intensity selecte via Moonlight intensity option.
With moonlight simulation switch on – light intensity will be gra ually changing following the natural moon cycle (Current moon phase
isplays the current moon phase simulate by the lamp).
Moonlight channel colour settings – customer can choose which LED channel will be use to moonlight simulation.
Moonlight time - – there can be set time for moonlight sunrise an sunset.
Pacific Sun Hyperion S/Triton S lamps – manua