Pacific Sun AR-PRO S User manual

AR-PRO
Algae reactor S/M/L
A simple and effective natural nutrient control
method that helps promote a healthy and thriving
reef tank!

Preface
Congratulations on your purchase!
Pacific Sun AR-PRO Algae Reactors are made with the highest quality materials, and made to
last!
The Pacific Sun Research and Development team are continually testing, developing and rele-
asing new features, and hence the purpose of this document is to touch on the basics of our
product and software.
Details about new features will be updated from time to time, but if you have any questions, please
contact us at:
[e-mail]
Best regards
Pacific Sun EU

A simple and effective natural nutrient control method that helps promote a healthy and thriving
reef tank!
The AR-Pro Algae reactor series incorporates a unique design that allows macro algae such
as Chaetomorpha to grow with great yields, leading to the effective nutrient export of unwanted
nitrates and phosphates.
In addition to nutrient control, the use of AR-PRO algae reactor provides other benefits such as
the consumption of excess CO2 and elevation of oxygen levels in the aquarium.
Recommended to be used on a reverse daylight cycle, helping to balance pH swings and create
a stable environment for the tank inhabitants.
Key factors:
-NO3 reduction
-PO4 reduction
-Dissolved Organics reduction
-Carbon dioxide reduction
-Increased Oxygen Levels
-Increase and stabilise pH
-Increased Redox levels
-Improve water quality
-Speed up corals calcification
-Helps create healthy natural conditions for all aquarium inhabitants.
-Replaces other methods of nutrient control such as Carbon Dosing and Bio-Pellets with a natural
solution.

Algea reactor schematic.
Below you can find description of all inlets/outlets coming from /to algea reactor.
Power supply input
Output connection
Effluent input from
calcium reactor
Input connection

Power supply input Effluent input from
calcium reactor
Output connection
Input connection
Input connection
Input connection
Adjusting valve

QUICK START GUIDE:
Caution: Please do not run the algae reactor dry! Failure to do so will cause per-
manent damage.
1). Carefully unpack the reactor and all of the contents.
2). Plug the power cable into the power supply and the other end into a standard
110-220 volt wall receptacle.
3). Connect the power supply to the LED inner segment. Ensure the power supply
is away and protected from the water source. Check that all LEDs light properly.
4). Connect feed pump to the bottom inlet of the reactor. Use flexible or hard
plumbing piping for inlet and outlet of the reactor.
5). Open the reactor and pull out the inner segment, then place small clumps of
algae on each layer.
6). Carefully place the inner segment back inside reactor, and secure lid by twisting
and tightening the screws.
7). Use a controller or timer to run the reactor on a reverse daylight schedule. For
best results the reactor should be turned on 1h before the main display lights go
on and remain on 1h after display lights are turned off.
8). Turn on the flow to the reactor and check for any leaks.
9). If you are using calcium reactor - connect effluent tubing(output from calcium
reactor) to proper port on AlR-PRO Algae reactor. It will help remove the rest of
carbon dioxide from effluent and increase pH in final effluent(also overally in main
tank/aquarium). If calcium reactor is not used - valve on Calcium port should be
completly closed.
10). Remember about inspecting your reactor every week or two and removing
some fast growin algea. To much them inside will block flow and decrease reactor
efficiency.

Specifications:
AR-PRO S
System Size: 100-500L
Recommended Flow Rate: 600-1000L/H
Body Material: High Quality Cast Acrylic
Dimensions: 150x150x450 mm
Hose Inlet/Outlet: 20 mm
Flow Pattern: Bottom Up
Light Type: Green Plant grow leds
Power consumption: 18,8W
Placement: AR-PRO reactors are made from reef safe materials which
allows placement of the reactor inside or outside of the sump.
AR-PRO M
System Size: 500-1000L
Recommended Flow Rate: 1000-1500L/H
Body Material: High Quality Cast Acrylic
Dimensions: 190x190x550 mm
Hose Inlet/Outlet: 20 mm
Flow Pattern: Bottom Up
Light Type: Green Plant grow leds
Power consumption: 23,5W
Placement: AR-PRO reactors are made from reef safe materials which
allows placement of the reactor inside or outside of the sump.
AR-PRO L
System Size: 1000-2000L
Recommended Flow Rate: 1500-2000L/H
Body Material: High Quality Cast Acrylic
Dimensions: 250x250x550 mm
Hose Inlet/Outlet: 20 mm
Flow Pattern: Bottom Up
Light Type: Green Plant grow leds
Power consumption: 25,8W
Placement: AR-PRO reactors are made from reef safe materials which
allows placement of the reactor inside or outside of the sump.

If you need technical support:
please contact with [email protected]!
Copyright
Pacific Sun Sp. Z o.o.
I Brygady Pancernej WP 10
84-200 Wejherowo
Poland
tel. + 48 58 778 17 17
email: [e-mail]
Manufactured in Poland, EU

Liebe Kunden,
Vielen Dank, dass Sie sich für Pacific Sun entschieden haben.
Mit dem Kauf dieses Gerätes haben Sie sich für ein Produkt von höchster Qualität entschieden. Es
wurde speziell für den Einsatz im Aquarium entwickelt und von Experten getestet.
Pacific Sun EU

Eine einfache und effektive Methode zur natürlichen Kontrolle des Gehalts an organischen Ver-
bindungen hilft, ein gesundes und sich gut entwickelndes Riffbecken zu erhalten!
Die AR-PRO-Algenreaktorserie umfasst ein einzigartiges Design, das ein schnelles Wachstum
von Makroalgen, wie Chaetomorpha ermöglicht, wodurch unerwünschte Verbindungen, wie
Phosphat und Nitrat effektiv aus dem Wasser entfernt werden.
Darüber hinaus bietet der Einsatz des AR-PRO-Algenreaktors zusätzliche Vorteile, wie die Ent-
fernung von überschüssigem CO2 und die Erhöhung des Sauerstoffgehalts im Aquarium.
Wir empfehlen den Einsatz des Reaktors im umgekehrten Tag/Nacht Modus, um Schwankungen
des pH-Wertes zu stabilisieren und eine stabile Umgebung für die Tankpopulation zu schaffen.
Nutzen Sie die Hauptvorteile:
Reduzierung von NO3
Reduzierung von PO4
- Reduzierung anderer organischer Verbindungen
- Reduzierung des Kohlendioxidgehalts
- Erhöhter Sauerstoffgehalt
- Erhöhung und Stabilisierung des pH-Wertes
- Erhöhung des Redoxfaktors
- Verbesserung der Wasserqualität
- Beschleunigung der Korallenverkalkung
- Hilft, gesunde, natürliche Bedingungen für alle Aquarienbewohner zu schaffen
- Ersetzt andere Nitratkontrollmethoden (wie, z.B. Kohlenstoff/Bio-Pellet-Dosierung) durch eine
natürliche Lösung.
- Reduzierung anderer organischer Verbindungen
- Erhöhung und Stabilisierung des pH-Wertes
- Reduzierung anderer organischer Verbindungen
- Erhöhung und Stabilisierung des pH-Wertes
- Reduzierung anderer organischer Verbindungen
- Erhöhung und Stabilisierung des pH-Wertes