PACOM PAC-VN70IIS-VFA12 User manual

PAC-VN70IIS-VFA12
IR Night Vision Outdoor Camera
INSTALLATION MANUAL
1 version 1.0.1



Thelightingflashwithanarrowheadsymbol,withinanequilateral
triangleisintendedtoalerttheusertothepresenceofnon‐insulated
dangerousvoltagewithintheproduct’senclosurethatmaybeof
sufficientmagnitudetoconstituteariskofelectricshocktopersons.

Theexclamationpointwithinanequilateraltriangleisintendedtoalert
theusertothepresenceofimportantoperatingandmaintenance
(servicing)instructionsintheliteratureaccompanyingtheappliance.


INFORMATION
ThisequipmenthasbeentestedandfoundtocomplywithlimitsforaClassAdigitaldevice,pursuanttopart15
oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferencewhen
theequipmentisoperatedinacommercialenvironment.Thisequipmentgenerates,uses,andcanradiate
radiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructionmanual,maycause
harmfulinterferencetoradiocommunications.Operationofthisequipmentinaresidentialareaislikelyto
causeharmfulinterferenceinwhichcasetheuserwillberequiredtocorrecttheinterferenceatitsown
expense.

WARNING
Changesormodificationsnotexpresslyapprovedbythemanufacturercouldvoidtheuser’sauthorityto
operatetheequipment.

CAUTION–Topreventelectricshockandriskofthefirehazards
‐DoNOTusepowersourceotherthanthatspecified.
‐DoNOTexposethisappliancetorainormoisture.

Thisinstallationshouldbemadebyaqualifiedservicepersonandshouldconformtoalllocalcodes.






2 version 1.0.1

Tableofcontent


Installationmanual

1.Precautions‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐4

2.Limitationofliability ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐5 

3.Disclaimerofwarranty ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐5 

4.Package
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐6 

5.Specialfeaturesofthemodel
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐7 

6.Installation
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐8~11 

7.Troubleshooting
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐12~13

8.Dimension(mm) ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐13 

9.Specification
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐14




OSDManual 
forfunctionscontrol‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐15~22





















3 version 1.0.1

1.Precautions
 Pleasereadthemanualcarefullybeforetheinstallationinordertosetupthecameracorrectlyandto
obtainthebestpicturequality.

 Pleasekeepthemanualingoodconditionforyourfuturereferenceandserviceapplication.

 Installationandservicesshouldbeonlycarriedoutbyanauthorizedpersonnelaccordingtolocalsafety
regulations.

 Ifanyliquidorsolidmattergetsintothehousing,immediatelydisconnectthecamerafrompowersupply
andhaveitcheckedbyyourauthorizeddealerbeforereusing..

 Avoidinstallingthecamerainextremelyhotorcoldplaces.

 Ifyouarenotacertifiedperson,nevertrytodismantlethecamera.Toavoidelectricshock,neverremove
thescrewsorcovers.Therearenopartsinsidethatneedmaintenancebytheuser.Allmaintenanceshould
becarriedoutbyqualifiedpersonnel.

 Avoidinstallingthecameraataplaceofhighhumidity.

 Avoidinstallingthecameraattheplaceexposedtogasoroil.

 Keepthetopglassofthelensalwayscleaninordertoobtainthebestpicturequalityallthetime.Be
carefulnottobestainedbyfingerprint.

 Don'tfacethecameradirectlytowardsunlightorsunlightreflectingarea.
CCDmaygodefectiveatthiscondition.

 Pleasegiveaspecialattentiontokeeptheunitfromdangerousdroporexternalshockduring
theprocessoftransportationorhandling.

 Nevertrytotouchthecamerainwethand.Itmaycauseanelectricshock.

 Donotexposethecameratoradioactivity.ItcausesaseriousdamageontheCCD.

















4 version 1.0.1

2.Limitationofliability

Thispublicationisprovided“ASIS”withoutwarrantyofanykind,eitherexpressorimplied,includingbutnot
limitedto,theimpliedwarrantiesofmerchantability,fitnessforanyparticularpurpose,ornon‐infringementof
thethirdparty'sright.Thispublicationcouldincludetechnicalinaccuraciesortypographicalerrors.Changesare
addedtotheinformationherein,atanytime,fortheimprovementsofthispublicationand/orthe
correspondingproduct(s).


3.Disclaimerofwarranty

Innoeventshallsellerbeliabletoanypartyoranyperson,exceptforreplacementorreasonablemaintenance
oftheproduct,forthecases,includingbutnotlimitedtobelow:

(1)Anydamageandloss,includingwithoutlimitation,directorindirect,special,
consequentialorexemplary,arisingoutoforrelatingtotheproduct;

(2)Personalinjuryoranydamagecausedbyinappropriateuseornegligentoperation
oftheuser;

(3)Unauthorizeddisassemble,repairormodificationoftheproductbytheuser;

(4)Inconvenienceoranylossarisingwhenimagesarenotdisplayed,duetoanyreason
orcauseincludinganyfailureorproblemoftheproduct;

(5)Anyproblem,consequentialinconvenience,orlossordamage,arisingoutofthe
systemcombinedbythedevicesofthirdparty.

(6)Anyclaimoractionfordamages,broughtbyanypersonororganizationbeing
photogenicsubject,duetoviolationofprivacywiththeresultofthatsurveillance‐
camera'spicture,includingsaveddata,forsomereason,becomespublicorisused
forthepurposeotherthansurveillance.


















5 version 1.0.1

4.Package
















Ext‐VideoCablex1
















Camerax1Instructionmanualx1
OSDmanualx1
Power+VideoCablex1
Tappingscrewsx3 Plasticanchorx3




















6 version 1.0.1

5.Specialfeaturesofthemodel

1. Higherresolutionof600TVL(D)/650TVL(N)
Thisunithascomeupwithaninnovativewayofincreasingcubicresolutiontomorethan30%higher
thanthatofconventional600TVLcameras.
Itupgradeshorizontalresolutionto600TVLandverticalresolutionto540TVLsothatthecubic
resolutionbecomes324KTVLwhileconventionalcamerasprovideonly240KTVL.

2. UnbeatableWDRPerformance
Thisunitprovidesaveryuniqueandfarsuperiorimagescanningcapabilityofdefiningthedetailsof
differentlycontrastedareascomparedwithanyotherconventionalWDRcameras.WithcurrentWDR
technologies,definingimagesinshadedareasaretypicallynotclearenoughwithover‐exposed
picturequality.Thiscameraprovidesaspecialresolutiontointelligentlyanalyzetheexposureratio
andtooptimizeitintoanunbeatablyclearimagequality.

3. SuperLowLightsensitivity
Thesystemspecifiesitselfasthebestresolutioninthemarketthatovercomesthelimitationof
compromisinglightsensitivityfromconventionalWDRcameras.
Withitsspecialtechnology,itprovidesremarkablelowlightsensitivityof0.1Lux/F2.0~0.0001Luxw
/Sens‐up512xwhichisatleast3timesbetterthananyotherconventionalWDRcameras.

4. 2D/3DNoiseReduction
2D/3DDNRachievementisanotherreferenceinnewWDRtechnology.
Itreproducesnoiselessimageswith2D/3DfilteringNoiseReductionTechnologysothatuserscansave
thevolumeofstoragemediaandHDDcapacityinDVR.
2DDNRhelpspreservededgedinthepicture,while3DDNRrealizesclearimageswithnoghosteffect.

5. DIS(DigitalImageStabilizer)
Thistechnologyreducesblurringassociatedwiththemotionofthesubjectbyusingpixelsoutsidethe
borderofthevisibleframetoprovideabufferforthemotion.
Increasingtheexposuretimewithoutblurringtheimagemakesthemovingsubjectstabilizeddigitally.

6. Anti‐ColorRolling
Withanoperationofawidedynamicrangecamerainanenvironmentwithafluorescentlighting,an
effectthatiscalled“colorrolling”usuallyhappensduetothelackofthesynchronizationbetweenthe
cameraandtheneonlight.
NewWDRtechnologytracksthelightchangesrelativetothecameraandadaptsitsowntimingtothe
periodicityoffluorescentilluminationtothesamplelightataconstantphase,virtuallyelimination
thecolorrollingeffect.













7 version 1.0.1

6.Installation

6‐1.HowtomounttoCeiling




①Drillthreescrewholesontheceilingplatetofixthreeanchors(supplied)intheholes.
②Fixtheplasticanchorsintheholes.
③Positionthemountingbracketonthescrewpoints.
④Fixthemountingbracketbytighteningthescrews.
⑤Slightlyloosenbolt(A)thenadjustTILT(180°)androtation(360°)ofthecamerausinga
serrationonthebracketandtightentheboltfirmly.
⑥Slightlyloosenbolt(B)thenadjustpan(360°)ofthecameraandtightentheboltfirmly




8 version 1.0.1

6‐2.HowtoinstalltoWall





①Drillthreescrewholesonthewallplatetofixthreeplasticanchors(supplied)intheholes.
②Fixtheplasticanchorsintheholes.
③Positionthemountingbracketonthescrewpoints.
④Fixthemountingbracketbytighteningthescrews.
⑤Slightlyloosenbolt(A)thenadjusttilt(180˚)androtation(360˚)ofthecamerausinga
serrationonthebracketandtightentheboltfirmly.
⑥Slightlyloosenbolt(B)thenadjustpan(360˚)ofthecameraandtightentheboltfirmly.

















9 version 1.0.1

6‐3.3‐Axisadjustment

①Pan 360˚
Slightly loosen Pan bolt then adjust pan of the camera using a serration on the
bracket and tighten the bolt firmly .
②Tilt 180˚
Slightly loosen Tilt bolt then adjust tilt of the camera using a serration on the bracket
and tighten the bolt firmly.
③Rotation 360˚
Slightly loosen Tilt bolt then adjust rotation of the camera using a serration on the
bracket and tighten the bolt firmly.
6-4. Lens external adjustment
6-5. EXT-Video
10 version 1.0.1

- How to use
Connect Extra video output (BNC cable) to LCD monitor as a picture.
6‐6Waterproofprocessingofcableendconnection

Makesuretouseabutyltape.(Donotuseasealingmaterialonthoseparts)

Itisusefultoconnectthecableendsfromcameratotheextensioncableforwaterproof.
Connectandtapethepowercables(Power‐Power/Ground‐Ground).
Bindthepowercablestogetherwiththetape.WhenDC‐Jackisused,tapetheDC‐DCjoint.
ConnectandtapetheRS485cables(RS485+ㅡTRX+/RS485‐ㅡTRX‐)
TapetheBNC‐BNCjoint.










11 version 1.0.1

7.Troubleshooting
Ifthereareproblemsinoperating,pleaserefertothechecklistbelow.Iftheproblempersists,pleasecontact
theagentwherethisproductispurchased.

ProblemsTroubleshooting
Nothingappearsonthescreen. Pleasecheckthatthepowercordandlineconnection
betweenthecameraandmonitorarefixedproperly.
 PleasecheckthatyouhaveproperlyconnectedVIDEO
cabletothecameraVIDEOoutputjack.
Theimageonthescreenisdim. Islensstainedwithdirt?Cleanyourlenswithsoft,
cleancloth.
 Setthemonitortopropercondition.
 Ifthecameraisexposedtotoostronglight,change
thecameraposition.
Theimageonthescreenisdark. Adjustthecontrastfeatureofthemonitor.
 Ifyouhaveanintermediatedevice,setthe75Ω/Hi‐Zproperly
(Pleasechecktheimpedance)
Thecameraisnotworking
properly,andthesurface
ofthecameraishot.
 Pleasecheckthatyouhaveproperlyconnectedthecamera
toanappropriatepowersource.

TheDAY/NIGHTmenu
doesnotwork.
 PleasecheckifDAYNIGHTmenuissetto‘AUTO1’.

TheSENS‐UPfunction
doesnotwork.
 PleasecheckthatAGCofEXPOSURESETUPmenuissetto‘OFF’.
 PleasecheckthatSHUTTERofEXPOSURESETUPmenuissetto
‘A.FLK’or‘FIXED’.
TheMOTIONDETECTION
functionisnotworking.
 PleasecheckifMOTIONDETECTIONfunctionisturnedon.
 PleasecheckifMDLEVEListoolow.
 PleasecheckthesettingoftheMDarea.
Colorisnotcorrect. PleasecheckthesettingofWHITEBALSETUPmenu.

Thescreenflickerscontinually.
 PleasecheckthatdirectionofcameraturnstowardtheSun.


















12 version 1.0.1

ProblemsTroubleshooting
 PleasecheckthepolaritybetweenRS‐485ControlPort
andRS‐485cable.

485ControlBoardConnectionPortRS‐485ControlPort
(+)CONNECTIONTERMINAL(TRX+)485+
(‐)CONNECTIONTERMINAL(TRX‐)485‐

 PleasecheckiftheinitialvalueoftheRS‐485Communication
setupmatchesbetweencameraandOSDControllerorDVR.

*RS‐485Communicationestablishmentinitialvalue
ItemCameraIDBAUDRATEUARTMODERETPKT
Initialvalue196008‐NONE‐1ENABLE
RS‐485
communicationfails.

 Werecommendthatyoumakegroundconnection
betweencameraandcontrollerforsafecommunicationcontrol.

 WhenRS‐485cableisnotproperlyconnected,
Awarningmessage‘ERRORRS‐485Connection.Pleasereconnectand
Reboot’isdisplayed.
Thenpleaseturnoffthepowerandconnectthecableagain.



8.Dimension(mm)










13 version 1.0.1

9.Specification



ClassNIGHTVISIONCAMAERA
12VDC/24VACPowerSource
100㎃(IROff)/4 0 0 ㎃(IROn)
CCD1/3 ” SonySuperHADⅡ
EffectivepixelsPAL:752(H)x582(V)
Image
Resolution600TVL(Day)/650TVL(Night)
ScanningSys2:1Interlace
SynchronizationInternal
Sync
FrequencyPAL:15.625KHz(H),50KHz(V)
Min.Illumination0Lux/IROn
VideoOut1Vp‐pComposite75Ohm
S/NRatioMorethan52dB(AGCOff)
ShutterSpeedPAL:1/50~90,000/sec.
GammaControlStandard:r=0.45
WhiteBalance1500°K~11,000°KAuto,ATW/Cor‐Roll/Push/Manual
Electrical
GainControl Standard:‐6dB~34dBAuto/MaximumbyOSD
IRSpectrum850nm8Øx14ea
ViewableDistanceUpto25m
IRLED
MTBFofIR20,000hours
OperatingTemp ‐10°C~50°CEnvironme
ntalHumidity0%RH~90%RH
Measurement104.3(W)x96(V)x277.3(L)
Function
WDROFF/ON
2D/3DNROFF/ON
Sens‐upOFF/x2~x512
MotionDetectionOFF/ON(8Zonesselectable)
DigitalZoomOFF/x1~x8.30
WhiteBalanceAuto,ATW/Cor‐Roll/Push/Manual
PrivacyMaskOFF/ON(8Zonesselectable)














14 version 1.0.1

OSDManualforfunctionscontrol

1.OnScreenMenu(OSD)
2.Settingupthemenu
1.PresstheTactSWtoenter<MAINMENU>.

2.Movethearrowtoaspecificmenu
bypushingtheTactSWupordown.

3.AdjusttheselectedfeaturebypushingtheTactSW
leftorright
HowtouseOSDbutton(TactSW)
 Press
- toenterthemenu
- tosavesettings
 Pushupordown
- toselectfunctions
 Pushleftorright
- toadjustalevelormodeofsub‐menu









4.Whencompleted,movethearrowindicatorto‘EXIT’andpresstheTactSWtofinishallsettings.





15 version 1.0.1


Note
∙If‘‘indicationappearsonaselectedsub‐menu,presstheTactSWtogetintoafollowingmenu.
∙If‘‐‐‐‘indicationappearsonanysub‐menu,itmeansthefunctionwiththismarkisdeactivated.
(Ex:WhenSENS‐UPisOFF,3‐DNRbecomesdeactivated‘‐‐‐‘)
3.LENS
SelectthelensandadjusttheSETUPsuitabletothetypeoflens.


WhenDClensisused.(Default)
1.PleaseselectthelensmodetoDCIRIS.
2.PresstheTactSWtoenterthe<DCIRISMENU>.
‐BRIGHTNESS:adjustthebrightnessofscreenwhentheenvironmentis
extremelybrightordark.
‐REACTION:Reactionspeedoftheshutterisadjustable.
Itisusefulwhenthelightconditionoftheenvironmentkeeps
changingquickly.

3.Save
PressSAVEtofinishallsettingsandreturnto<MAINMENU>


WhenMANUALlensisused.
1.PleaseselectthelensmodetoMANUAL.
2.PresstheTactSWtoenterthe<MANUALIRISMENU>.
‐BRIGHTNESS:sameasabove
‐REACTION:sameasabove
4.EXPOSURE
(1)AGC(AutoGainControl)
‐OFF:DeactivatestheAGCfunction.
‐LOW:Allowsautomaticgaincontrolfrom0to20dB.(Default)
‐MIDDLE:Allowsautomaticgaincontrolfrom0to30dB.
‐HIGH:Allowsautomaticgaincontrolfrom0to42dB.

Thehigherthegainlevel,thebrighterthescreenbecomeswhilethehigherthenoiseaswell.

(2)SHUTTER
A.AUTO:Theshutterspeediscontrolledautomatically.(Default)
B.FLK:PleaseselectFLKmodewhenflickeringoccursonthe
screen,duetoanimbalancebetweenilluminationandfrequency.
C.FIXED:Theshutterspeediscontrolledmanually.
‐Youcanselectthespeedfrom‘1/60’to‘1/90,000sec.(NTSC),‘1/50’to‘1/90,000sec.(PAL).
‐YoucanselectDigitalSlowShutterbetweenx2~x512.(DSS)

PleaseuseFIXEDmodeonlywhenthelightlevelofthesurveillanceareaisfixedallthetime.

(3)SENS‐UP
‐Lowlightsensitivityisgreatlyimprovedwiththeuseofthisfunction.
‐Lowlightsensitivitylevelisadjustablefrom2to512times.
‐WhenSEN‐UPlevelishigher,thepicturebecomesbrighterwhilenoiseis
increasedatthesamerateofSENS‐UP.

ON:AdjustableSENS‐UPlevelbetweenx2~x512.
OFF:SENS‐UPisdisabled.
Defaultsettingis<x8>
16 version 1.0.1

Note
∙WhentheSHUTTERissettoMANUALmode,SENS‐UPdoesnotoperate.
∙WhentheAGCissettoOFF,SENS‐UPdoesnotoperate.

(4)INITIALSET
InitializeallsettingsofEXPOSUREmenu.

(5)SAVE
5.DAY/NIGHT
Itisusedtoimprovethesensitivityandclarityofpicturequalityatlowlight

‐DAY:Theimageisalwaysdisplayedincolor.
‐NIGHT:Theimageisalwaysdisplayedinblackandwhite.
‐AUTO1:TheimageisautomaticallyconvertedtoB/WfromColorat3lux.

 ● IRWDRLEVEL:SelectAnti‐IRsaturationlevel‐OFF/LOW/MIDDL /HIGHE
● IRWDRADJUST:Adjustthevalueineachofselectedlevel‐0~6

‐AUTO2:TheimageisautomaticallyconvertedtoB/WfromColorat3lux.
∙D/NLEVEL:LOW/MIDDLE/HIGH
∙FILTERDLY:SelectthedurationtimeaboutchangingtheDay/Nightmode.
(1SEC,3SEC,5SEC,10SEC,15SEC,30SEC,60SEC)
∙NIGHTBURST:BurstON/OFFselectable.
∙INITIALSET:InitializeallsettingsofAUTO2menu.

Defaultsetting
‐Infraredcamera:AUTO1
‐Non‐Infraredcamera:AUTO2
6.WDR/BLC/ECLPS
Theimagequalityisgreatlyimprovedwiththeuseofthismodewhenthereisa
strongbacklightbehindtheobject.

‐OFF:DeactivatestheWDRfunction.
‐WDR:Camerascansbothofbrightlitbackgroundandshadedareadistinctively
underanextremelycontrastedlightsituation.(LOW/MIDDEL/HIGH)
‐BLC:Enablesausertodirectlyselectadesiredareafromapictureand
toviewtheareamoreclearly.(LOW/MIDDEL/HIGH)
‐











17 version 1.0.1

ECLIPSE:
 Canmasktheheadlightstoviewcarlicensenumberplatemoreclearly.
 Canselectmaskingcolor.
 AdjusttheECLIPSlevelattheGAINCONTROLasOFFmode.










7.WhiteBalance(WHITEBAL)

Thisisusefultooptimizethewhitebalalncecontrolunderacertainartificiallightingareawhereastandard
whitebalanceconditionisnotsuitable.
‐ATW(AutoTrackingWhiteBalance)
Thismodecanbeusedwithinthecolortemperature
rangeof1,500˚K~11,000˚K.(Default)
‐COL‐ROLL
Anticolorrollingmode.
Useitonlywhentherollingisseverelyshown.
‐MANUAL
Recommandedtouseitwhenthelighttemperatureisfixedallthetime
SelectINDOORorOUTDOORmode.
‐PUSH(Pushlock)
UsethiswhentheWhiteBalanceisdeviated.
FacethecameratowardthewhitewallorwhitepaperandpresstheTactSW

Note
WhiteBalancemaynotworkproperlyunderthefollowingcondition
‐ Whenthecolortemperatureoftheenvironmentsurroundingthesubjectisoutofthe
controlrange.(e.g.clearskyorsunset)
‐ Whentheambientilluminationofthesubjectisdim.
‐ Ifthecameraisdirectedtowardsafluorescentlightorisinstalledinaplacewhere
illuminationchangedramatically,theWhiteBalanceoperationmaybecomeunstable.





18 version 1.0.1

8.2D‐DNR(2DNoiseReduction)
‐LOW
‐MIDDLE
‐HIGH
‐DISABLED:Deactivates2DNR.Noiseisnotreduced.
‐OFF:Activates2DNR(Level:0).Noiseisnotreduced.

Note
<Badpixeldetection>functionisoperatedonlywhen<2D‐DNRDISABLED>isselected.



9.3D‐DNR(3DNoiseReduction)

Thebackgroundnoiseinthelowlightleveldecreasesautomatically
asthelevelofgainchanges.

‐DNRLEVEL
Adjustthenoisereductionlevel.
‐DESTINATION
Adjustthe3DNRgain.
‐GLOBALMOVEMENT
Controlghostphenomenon
10.EFFECTS  
‐D‐ZOOM:Youcanuseadigitalzoom.
∙ZOOM:x1~x8.30
∙DZOOMPAN:‐100~100
∙DZOOMTILT:‐100~100
‐IMAGEFREEZE:Youcanviewstillorliveimage.
‐D‐EFFECT
∙V‐FLIP:Youcanflipthepictureverticallyonthescreen.
∙MIRROR:Youcanflipthepicturehorizontallyonthescreen.
∙ROTATE:Youcanflipthepicturerotativelyonthescreen.
‐CONTRAST:0~100
‐SHARPNESS:0~100
‐COLORADJUST
∙COLOR:ON/OFF
∙COLORLEVEL:0~200
.COLORHUE:‐180~180
.REDGAIN:‐100~100
.BLUEGAIN:‐100~100
‐TARGETCROSS:Display‘╇’onthescreen
∙COLOR:BALCK,GRAY,WHITE,RED,GREEN,YELLOW
∙MOVEX:‐100~100
.MOVEY:‐100~100
.INITIALSET
.SAVE

Note
AtTARGETCROSSfunctionisinoperation,‘╇’displayshalldisappearifMOTIONDETfunctionis‘ON’
19 version 1.0.1

‐BADPIXEL:BADPIXELcompensation
∙BPDETECTION:Makethescreencompletelyblackbycoveringthecamera.
∙SEARCHAREA:XSTART/YSTART/WIDTH/HEIGHT
.THRESHOLD:40~1024
.SAVE
(UsersmaysimplyactivateBPDETECTIONandgodirectlytoSAVE.ThenBadpixelsinfullscreenare
compensatedautomatically)

‐INITIALSET:InitializeallsettingsofEFFECTSmenu.
(TARGETCROSSandBADPIXELmodesarenotinitialized)
‐SAVE

11.SPECIALMENU

CAMNAME
‐ Pleasepositionthearrowtopointto’CAMNAME’byusingthe
UPorDOWNselection.
‐ Pleaseselect‘ON’byusingtheLEFTandRIGHTselection.
Pleasepressthebuttontocomplete‘ON’.

Note
If‘OFF’isselected,theCAMNAMEdoesnotappearonthemonitorevenifithasbeeninput.

‐ Upto15lettersareofferedfortheCAMNAME.
PleasemovethecursortothelettertochoosebyusingtheUP
andDOWNselections.
SetanIDfromA~Z/a~z/0 ~ 9 byusingtheUP,DOWN,LEFT
andRIGHTSelections.
Lockinthelettersbyusingthebutton.
∙Whentheletterislockedin,thecursormovestothenextspace.
PleaserepeattheabovetoinputCAMNAME.

☞Note
∙Forawrongnamehasbeeninput,
‐IfyoupressthebuttonaftermovingthecursortoCLR,all
letterswillbeerased.
‐Ifyouwanttocorrectaletter,pleasemovethecursortothearrowatthebottomleftofthe
screenandpressthebutton.
‐Pleasepositionthecursorontheletteryouwishtocorrect,andthenmovethecursoronto
theletteryouwishtochooseandpressthebutton.

‐ Whenanamehasbeenchosen,pleaseselectapositionforthenametodisplay.
Pleasemovethecursor
onto’POS’andthenpressthebutton.
Thenamewillappearat
thetoplefthandcorner.
Pleasefindthepositionyouwishtodisplaythenamebyusingthe4directional
selections,andthenpresstheButton.

‐ Please select ‘END’and then press the Button to complete CAM NAME input.
20 version 1.0.1