Pacvac Superpro 700 Installation guide

Commercial Back Pack
Vacuum Cleaners
Product & Training Manual
Support: 08 9479 1444


For service and help contact Pacvac on 08 9479 1444
or visit our website at www.pacvac.com for a list of your nearest
Gold Level Retailers and Service Centres.
Revised: November 2012 Read the instruction manual before using the machine.
Retain for future reference.
Original
Instructions


Your Pacvac Pty Ltd (Pacvac) product has been manufactured to meet our highest quality standards.
We urge you to take good care of your product and be sure to follow instructions carefully. This will provide
you with the best possible performance and lifespan of the product.
The inclusion of the following paragraph is a requirement by Australian Law. It explains that consumers
have rights by law regardless of any warranties provided or not by a manufacturer or supplier.
“Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure.”
In addition to guarantees under Australian Consumer Law, Pacvac warrants all machines and their
components against faulty material and/or workmanship for a period of two years from the date
of purchase by the consumer. The following explains conditions and what to do in the event of a claim:
• Pacvac will replace parts determined as faulty however this does not cover reasonable wear through
normal use of any consumable parts, such as but not limited to, bags, lters, hoses, power cords,
carbon brushes and oor tools etc.
• Warranty does not cover any machine or component that has been altered, abused, neglected,
modied, used with non-genuine Pacvac components or has not been used and maintained
as indicated in the Product and Training Manual.
• Warranty repairs can only be carried out by an authorised Pacvac Retailer or Service Agent.
Visit our website or call on the number above for your nearest location.
• All reasonable expenses associated with returning goods for a warranty claim are the consumer’s
responsibility.
• Claims must be made within two years of the date of purchase and proof of purchase must be
supplied with the claim.
• To make a claim under warranty, take the product with proof of purchase to the place of purchase.
In the event the place of purchase does not satisfactorily rectify the matter, please contact Pacvac
using the contact details above.
PACVAC PTY LTD
ABN: 60 709 396 593
182 Daly Street
BELMONT WA 6104
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Web: www.pacvac.com
Page 1
Page 2
Page 2
Page 3
Page 3
Page 4
Page 5
Page 5
Page 6
Page 7
Page 8
Page 9
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23


Warranty
General Safety Instructions
Product Specic Safety Instructions
Symbol Denitions
Patents
Safety and Maintenance Checks
Productivity Booster Kit
Pacvac Gold Level Service
Wear Right
Work Right
Operate Right
Troubleshooting Guide
Service Requirements
Superpro 700 Parts Prole
Superpro 700 Specications
Superpro duo 700 Parts Prole
Superpro duo 700 Specications
Superpro micron 700 Parts Prole
Superpro micron 700 Specications
Superpro trans 700 Parts Prole
Superpro trans 700 Specications
Superpro wispa 700 Parts Prole
Superpro wispa 700 Specications
Superpro 700 Series Harness, Accessories Parts Prole
Optional Extras
International Authorised Distributors
Notes

1


Support: 08 9479 1444
2 3

1. This Manual shall be considered an integral part
of the machine and should be carefully looked after
for subsequent reference.
2. WARNING Read this instruction manual before
using this machine and always follow the Safety
and Maintenance instructions.
3. WARNING Operators shall be adequately instructed
on the use of this machine.
4. WARNING This machine is not suitable for picking
up hazardous dust (Contact Pacvac for specic
equipment for this use).
5. WARNING Do not allow the power cord to come
into contact with rotating brushes of oor tools.
6. WARNING Do not use this machine in wet conditions.
7. CAUTION This machine is for indoor use only.
8. CAUTION This machine shall be stored indoors only.
9. Remove the machine from packaging and ensure
it and all its accessories and attachments are present
and in perfect condition. Contact the place of purchase
immediately in the event of any discrepancies.
10. The electrical specications of this machine are noted
on the data plate which is located near the power
switch. Ensure the specications correspond to those
of the mains power supply in your area. If the machine
is without a data plate, contact the place of purchase
immediately.
11. This machine is intended for commercial use, for
example in hotels, schools, hospitals, factories, shops
or ofces.
12. Do not restrict the vacuum cleaner’s airow. Maintain
the vacuum cleaner regularly so that all lters and
openings are free of dust, lint, hair build-up or anything
else which may affect airow. Refer to the maintenance
instructions in the Product & Training Manual.
13. If the machine has been dropped, damaged, left
outdoors or has been exposed to liquids, return it
to your local Authorised Pacvac Service Agent for
a safety check.
14. Do not use the machine to pick up ammable
or combustible liquids, such as petrol etc. and
do not use in areas where they may be present.
15. Do not vacuum anything that is burning or smoking
such as cigarettes or hot ashes.
16. Do not vacuum up hard or sharp objects such as
glass, nails, screws etc.
17. Keep hair, loose clothing, ngers and all parts of the
body away from moving parts and openings.
18. Keep the machine and power cord away from heated
surfaces.
19. Do not unplug the machine while it is turned on.
Turn the machine off, turn the power off at the
power outlet then unplug by grasping the plug and
pulling gently to unplug.
20. Do not handle the machine, power cord or plug
with wet hands.
21. Unplug from power point when not in use, before
servicing or before changing lters and attachments.
22. Do not pull or carry the machine by the power cord.
23. Do not close doors on the power cord and do not
pull the cord around sharp edges or corners.
24. Regularly check the power cord for damage, such as
cuts, abrasions, exposed wiring or aging. If the power
cord or plug is damaged, the complete power cord
must be replaced by your local Authorised Pacvac
Service Agent in order to avoid an electric shock. The
power cord should only be replaced with a Pacvac
Genuine Spare Part with the same specications.
25. Store in an appropriate place after use to prevent
tripping accidents.
26. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the machine by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with
this machine.
27. Use only the manufacturer’s recommended
attachments and/or replacement parts.

1. WARNING This machine is intended for the
vacuuming of dry dust and/or small debris off dry
carpeted or hard oor surfaces in indoor areas only.
2. WARNING Do not use the machine without the dust
bag and lters in place.
3. WARNING Do not place the Superpro duo 700 model
on the ground while the machine is turned on. This can
result in irreparable damage to the motor.
4. WARNING Do not plug the Superpro trans 700 into
a power supply other than 110-120V, 400Hz. An
alternate power supply can cause irreparable damage
to the motor and other electrical components.
5. The following models have a “A”-weighted emission
sound pressure level (measured at 1.5 meters) of:
Superpro 700 - 66 ± 3dB(A)
Superpro duo 700 - 74 ± 3dB(A)
Superpro wispa 700 - 66 ± 3dB(A) normal mode/
62 ± 3dB(A) wispa mode
Superpro micron 700 - 65 ± 3dB(A)
Superpro trans 700 - 63 ± 3dB(A).
6. WARNING Only use the socket outlet on the machine
for purposes specied within these instructions.
7. This appliance may be tted with a power socket
outlet. A power socket outlet is designed for use with
applicably approved electric powerhead attachments.
Powerhead attachments use rotating brushes to agitate
carpet bres in order to dislodge dust and/or debris.
Maximum wattage for such attachment shall not exceed
200 watts.
8. Floor Tool and Attachment Use
Part No. UA908W - Floor Tool
is intended for vacuuming of dry dust and debris
off oor surfaces.
Part No. KC910 - Dusting Brush
is intended for vacuuming of dry dust from blinds
and other delicate surfaces.
Part No. KC911 - Crevice Tool
is intended for vacuuming of dry dust and debris
from crevices.
Part No. KC912 - Upholstery Tool
is intended for vacuuming of dry dust from
upholstered surfaces.

1.

 
Do not dispose of electrical appliances as unsorted
municipal waste, use separate collection facilities.
Contact your local government for information
regarding the collection systems available.
If electrical appliances are disposed of in landlls
or dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging
your health and wellbeing.

 
 
 
2.
The CE Mark certies that a product has met
EU consumer safety, health or environmental
requirements.
3.
Class II, Double Insulated Appliance.
4.
The compliance label indicates that the product
complies with the applicable standard and
establishes a traceable link between the equipment
and the manufacturer, importer or their agent
responsible for compliance and for placing it
on the Australian market.
5.
Operator’s Manual; Operating Instructions
6.
Attention!
7. Transportation and Storage
This appliance and attachments should be packed
in double wall corrugated cardboard boxes with
dimensions of approximately 33cm x 33cm x 54.5cm.
Stack levels of boxes shall not exceed four units in
a vertical position.



The following patents apply.
AU Registered Design 326911
EP Registered Design 001617051-0001

 The motor is equipped with
a thermostat. If for any reason, the vacuum
cleaner should over-heat, the thermostat will
automatically turn the unit off. Should this
occur, turn off the switch and unplug the
vacuum cleaner from the electrical outlet and
conduct safety and maintenance checks.
Allow the cleaner to cool for approximately
30 minutes. To re-start, plug into a power
point and switch back on.


Support: 08 9479 1444
4 5

Remove and clean external motor lter.


 Remove, empty
and clean
Hypercone
dust bag.
Remove and
tap gently to
clean Hypercone
HEPA lter.
Check all
power cords,
for cuts, abrasions
and exposed wiring.
Wind up power cord
from machine end.
Store power cord
as shown.
Check the oor tool, wand,
bent hand piece and hose
for any obstructions.


 
   
  Contains information on how to operate right and work right as well
as troubleshooting and maintenance tips. Great for group training
sessions or for the individual user.
 
   
  Used to compliment training sessions and includes proformas
for attendance, assessment and evaluation with personalised
certicates upon completion of the training session.

A cleaner’s quick reference guide poster for safety, correct use,
maintenance and troubleshooting.

Simply contact Pacvac or your supplier and request the Productivity Booster Kit for your machine.
(Limits may apply).


Our Productivity Booster Kits are comprehensive training resources designed to help train professional
cleaners to work smarter, cleaner and healthier - saving both time and money.

Pacvac is committed to providing not just great products but also service and support to match. This is why
we have developed our Gold Level Retailer and Gold Level Service Agent program. When searching for our
products, service or support we recommend our Gold Level partners.
Gold Level Retailers stock a comprehensive range of Pacvac products from equipment to genuine spare parts.
Gold Level Service Agents can provide servicing for your equipment in
a timely manner and with genuine parts.
Visit www.pacvac.com for more information or give us a call, we are always happy to assist you!


Support: 08 9479 1444
6 7


• Rotate the dome lid to suit left or right handed vacuuming.
• Loosen the shoulder straps.
• Adjust the length at top of shoulder strap (if required).
• Lift the back pack by one shoulder strap.
• Then slide your free arm into the other strap.

• Tighten the hipband so the machine rests
comfortably on your hips.

• Pull down on shoulder straps for a comfortable t.
• Do up chest strap to secure back pack.

• Make sure the harness is resting on your hips.






• Find the most easily located power point. This is your starting location at the sh’s head.
Your turnaround is the ‘tail’.
• Check the room layout (position of desks, tables, chairs, ttings etc.)
• Check the condition of the oor - how dirty it is on a scale of 1 to 10.

• See in your mind the shbone method over the entire area or room to be cleaned.
• Decide which areas are to be detail cleaned (the spine), or spot cleaned (the ribs).

• Work away from the power point.
• Work one side of the shbone towards tail. Then back the other side towards head.
• Work to the plan - long strokes for the detail clean area and short dabs for the spot cleans.



Start
Heavy Trafc Areas - Detail Clean
Light Trafc - Spot Clean


Support: 08 9479 1444
8 9



1. Stand upright, with the bent hand piece section parallel to the oor.
2. Hold the bent hand piece with one hand at a comfortable arm’s length.
3. Move forward and away from the power point.
4. Use easy underarm swinging motion when detail cleaning and short dabs when spot cleaning, always
standing upright.
5. Once the end of the power cord has been reached and work completed, return to the power point along
the cord line and disconnect the power cord from the power point.
6. If work is not completed move to the next area, connect power cord to the nearest power point and
repeat steps 1 through 6.
7. Remove back pack by sliding the one of the straps off the shoulder, while raising the other arm/shoulder
to hold strap in place. Slowly lower the shoulder and lower the back pack to the oor, .
8. If work is completed disconnect power cord from power point then wind from the back pack towards
the end of the power cord to reduce likelihood of cable twists. In the process check for nicks, cuts,
fractures, and knots.
4
6
  
Back Pack not working Power cord not rmly plugged
into power point, short lead,
or machine.
Check all plugs and sockets are rmly
plugged in.
Back pack shuts off due to
high motor temperature.
Turn main switch off and unplug
the back pack. Conduct safety and
maintenance checks found in the
Product and Training Manual or as
per labelling on the machine. After 30
minutes (60 minutes for wispa) the
back pack should be ready for use.
If not contact the number below
for your nearest Authorised Pacvac
Service Agent.
Circuit breaker or RCD has
tripped.
Reset circuit breaker or RCD.
Back Pack as no/poor suction Hypercone dust bag full. Remove, empty and clean Hypercone
dust bag.
Hypercone dust bag not
installed correctly.
Remove and empty Hypercone dust
bag making sure the rubber edging is
correctly tted around the canister.
Hose not installed correctly. Reconnect hose and ensure correctly
sealed.
Blockages. Remove hose, wand and oor tools;
remove any blockages.
Filters blocked. Clean Hypercone HEPA lter and
external motor lter.

Our products are designed and built to be functional and durable. As a result, if you maintain your vacuum
cleaner as instructed, it is unlikely to require servicing. For information on use and maintenance please read
the Product and Training Manual thoroughly. Should you require servicing we recommend our Pacvac Gold
Level Service Centres. For your nearest centre visit www.pacvac.com, alternatively contact Pacvac on
08 9479 1444 or e-mail [email protected].

Quote these part numbers when ordering spare parts
   
1. Dome lid KC251
2. Hypercone paper bag (Packet of 5) AF101
3. Hypercone dust bag KC502HC
4. Hypercone HEPA lter KC270
5. Main vacuum canister KC252
6. Motor gasket KC253
7. Motor 240V 1000W 2 stage ow through UP118
8. Motor gasket KC253
9. Toggle latch KC131
10. Intermediate noise insulation PV254
11. Intermediate housing IEC KC256IEC
12. Power inlet C14 KC257IEC3
13. Power outlet C18 KC257
14. Switch rocker 12A 250V 5E4 VS261
15. Screw pan plastite 5x20 N/A
16. Noise insulation motor PV255
17. Short lead holder KC262H
18. Short lead IEC type 420mm 10A 3c 1mm² KC109IEC
(AU, NZ)
19. Motor lter cage KC264
20. External motor lter PV259
21. Screw ST 6x25 N/A
22. Bottom cap KC258
23. Extension cord 18m 10A 3c 1mm² (AU, NZ) KC11118
Power Cord:
UK 18m 10A 3c 1mm² C13 (UK, SG, IN, AE) KC108UKIEC
EU 18m 10A 3c 1mm² C13 (EU) KC108EUIEC

Support: 08 9479 1444 1110

Volts / Frequency: 220-240V~50Hz
Motor: 240V 1000W 2 Stage Flow Through
Noise Level: 66dB(A) ± 3dB(A) (at 1.5m)
Filtration: 4 stage, 99.99% efciency at 0.3 micron
Airow Volume: 38 litres per sec
Tank: Capacity: 5 litres
Weight: 5.0kgs (excluding power cord and hose)

























Technical specications, part numbers and parts proles are subject to change without notice.

Quote these part numbers when ordering spare parts
   
1. Dome lid KC251
2. Hypercone paper bag (Packet of 5) AF101
3. Hypercone dust bag KC502HC
4. Hypercone HEPA lter KC270
5. Main vacuum canister KC252D
6. Motor gasket KC253
7. Motor 240V 1000W 2 stage by-pass HV1208
8. Motor gasket KC253
9. Toggle latch KC131
10. Intermediate noise insulation PV254
11. Intermediate housing IEC KC256IEC
12. Power inlet C14 KC257IEC3
13. Power outlet C18 KC257
14. Switch rocker 12A 250V 5E4 VS261
15. Screw pan plastite 5x20 N/A
16. Noise insulation motor PV255
17. Short lead holder KC262H
18. Short lead IEC type 420mm 10A 3c 1mm² KC109IEC
(AU, NZ)
19. Motor lter cage KC264
20. External motor lter PV259
21. Screw ST 6x25 N/A
22. Bottom cap duo KC258D
23. Extension cord 18m 10A 3c 1mm² (AU, NZ) KC11118
Power Cord:
UK 18m 10A 3c 1mm² C13 (UK, SG, IN, AE) KC108UKIEC
EU 18m 10A 3c 1mm² C13 (EU) KC108EUIEC

Support: 08 9479 1444 1312

Volts / Frequency: 220-240V~50Hz
Motor: 250V 1000W 2 Stage By-pass
Noise Level: 74dB(A) ± 3dB(A) (at 1.5m)
Filtration: 4 stage, 99.99% efciency at 0.3 micron
Airow Volume: 38 litres per sec
Tank: Capacity: 5 litres
Weight: 5.0kgs (excluding power cord and hose)

























Technical specications, part numbers and parts proles are subject to change without notice.

Quote these part numbers when ordering spare parts
   
1. Dome lid KC251
2. Micron paper bag (Packet of 5) KC287
3. Dust bag at bottom PV502
4. Micron HEPA lter KC288
5. Main vacuum canister KC252M
6. Motor gasket KC253
7. Motor 240V 1000W 2 stage ow through UP118
8. Motor gasket KC253
9. Toggle latch KC131
10. Intermediate noise insulation PV254
11. Intermediate housing IEC KC256IEC
12. Power inlet C14 KC257IEC3
13. Power outlet C18 KC257
14. Switch rocker 12A 250V 5E4 VS261
15. Screw pan plastite 5x20 N/A
16. Noise insulation motor PV255
17. Short lead holder KC262H
18. Short lead IEC type 420mm 10A 3c 1mm² KC109IEC
(AU, NZ)
19. Motor lter cage KC264
20. External motor lter PV259
21. Screw ST 6x25 N/A
22. Bottom cap KC258
23. Extension cord 18m 10A 3c 1mm² (AU, NZ) KC11118
Power Cord:
UK 18m 10A 3c 1mm² C13 (UK, SG, IN, AE) KC108UKIEC
EU 18m 10A 3c 1mm² C13 (EU) KC108EUIEC

Support: 08 9479 1444 1514

Volts / Frequency: 220-240V~50Hz
Motor: 240V 1000W 2 Stage Flow Through
Noise Level: 65dB(A) ± 3dB(A) (at 1.5m)
Filtration: 4 stage, 99.99% efciency at 0.3 micron
Airow Volume: 38 litres per sec
Tank: Capacity: 5 litres
Weight: 5.0kgs (excluding power cord and hose)























Technical specications, part numbers and parts proles are subject to change without notice.



Quote these part numbers when ordering spare parts
   
1. Dome lid KC251
2. Hypercone paper bag (Packet of 5) AF101
3. Hypercone dust bag KC502HC
4. Hypercone HEPA lter KC270
5. Main vacuum canister KC252T
6. Motor gasket KC253
7. Motor 120V 950W 2 stage ow through UP243
8. Trans motor sealing ring KC253A
9. Toggle latch KC131
10. Bridge rectier 35A UP246
11. Intermediate noise insulation PV254
12. Intermediate housing KC256
13. Switch rocker 12A 250V 5E5 VS261
14. Screw pan plastite 5x20 N/A
15. Noise insulation motor PV255
16. Motor lter cage KC264
17. Screw pan plastite 3x12 PV299
18. Cable clamp KC262
19. Cabled grommet KC406
20. External motor lter PV259
21. Screw 6x25 N/A
22. Bottom cap KC258
23. Cable UP109USA
24. Fuse Holder KC260
25. Fuse 10A time lag KC260F
26. Power outlet C18 KC257

Support: 08 9479 1444 1716

Volts / Frequency: 120V~400Hz
Motor: 120V 950W 2 Stage Flow Through
Noise Level: 63dB(A) ± 3dB(A) (at 1.5m)
Filtration: 4 stage, 99.99% efciency at 0.3 micron
Airow Volume: 29 litres per sec
Tank: Capacity: 5 litres
Weight: 5.0kgs (excluding power cord and hose)

























Technical specications, part numbers and parts proles are subject to change without notice.




Support: 08 9479 1444 1918

Volts / Frequency: 220-240V~50Hz
Motor: 240V 1300W Single Stage Flow Through
Noise Level: Normal mode 66dB(A) ± 3dB(A) (at 1.5m) / Wispa mode 62dB(A) ± 3dB(A) (at 1.5m)
Filtration: 4 stage, 99.99% efciency at 0.3 micron
Airow Volume: 32 litres per sec
Tank: Capacity: 5 litres
Weight: 5.0kgs (excluding power cord and hose)
Quote these part numbers when ordering spare parts
   
1. Dome lid KC251
2. Hypercone paper bag (Packet of 5) AF101
3. Hypercone dust bag KC502HC
4. Hypercone HEPA lter KC270
5. Main vacuum canister KC252W
6. Motor gasket foam KC253B
7. Motor 240V 1300W single stage ow through G118
8. Motor spacer KC253S
9. Motor gasket KC253
10. Toggle latch KC131
11. Intermediate noise insulation P254
12. Intermediate housing 1 hole KC256HC
13. Power inlet hot condition C16 KC257HC
14. Switch rocker intermediate12A 250V 5E4 VS261W
15. Screw pan plastite 5x20 N/A
16. Two speed PCB board V2 G2SV2
17. Noise insulation motor P255
18. Noise insulation bottom lid P255B
19. Motor lter cage KC264
20. External noise insulation P259
21. Screw ST 6x25 N/A
22. Connector right angle HC C15 PV257RHC
22b. Short lead rubber 420mm 10A 3c 1mm² (AU, NZ) KC109SL
23. Extension cord 18m 10A 3c 1mm² (AU, NZ) KC11118
24. Bottom cap KC258
25. Hole plug KC262P



















 





Technical specications, part numbers and parts proles are subject to change without notice.




Support: 08 9479 1444 2120

Part No. UA908
Combination oor tool Part No. UA9272 Bottom plate
(suits combination oor tool)
Part No. UA917H
All purpose oor tool
Part No. UA926
Turbo head
Part No. UP112PB
RCD Piggy back
Part No. KC928
Powerhead set complete Part No. KC909 Wand telescopic
REV : SEP 09 P102
Part No. UA913M
Bent hand piece metal
NOTE: Not suitable for
commercial use















Quote these part numbers when ordering spare parts
   
1. Bolt 5x20 N/A
Nut 5mm nyloc N/A
Washer 3/16 x3/4 N/A
Washer 3/16 x7/16 N/A
2. Carrying frame KC120
3. Shoulder strap pair KC121
4. Cord restraint KC268
5. Back support padding KC263
6. Hose complete 32mm 1.2m KC320
6a. Machine end connector 32mm KC200
6b. Hose cuff hull 32mm UA914
6c. Hose clip ring 32mm UA915
6d. Hose 32mm 1.2m KC350
6e. Bent hand piece 32mm KC330
7. Two piece wand 32mm KC9092
8. Crevice tool 32mm KC911
9. Combination oor tool with wheels 32mm x 285mm UA908W
10. Dusting brush 32mm KC910
11. Upholstery tool 32mm KC912
Technical specications, part numbers and parts proles are subject to change without notice.



Support: 08 9479 1444 23


Inventa Cleantec Pvt Ltd
C-31 Sector 63
NOIDA
Distt. Gautam Budh Nagar 201 301
INDIA
Ph: + 91 120 2401086
Fax: + 91 120 2401087
Web: www.inventacleantec.com

Bl Corporation
6-62-12 Shibayama
Funabashi-shi, Chiba-Ken 274-0816
Japan
Ph: + 81 47 464 1462
Fax: + 81 47 464 1477
Web: www.bicorp.co.jp

Proquip NZ Ltd
47 Fitzherbert Street,
Petone
Wellington
New Zealand
Ph: + 64 4 566 7847
Fax: + 64 4 576 0430
Web: www.cleangear.co.nz

Viking Cimex AS
Prof. Birkelandsvei 24 A-1
1081 Oslo
Norway
Ph: 47 22 79 35 35
Fx: 47 22 79 35 40
Web: www.skovly.no

Klenco (Singapore) Pte Ltd
18 Gul Crescent,
Singapore 629527
Ph: + 65 6862 3388
Fax: + 65 6861 7575
Web: www.klenco-asia.com

Klimatehnik d.o.o.
Brnciceva ulica 13
1231 Ljubljana
Slovenia
Ph: [phone]
Fax: [phone]
Web: www.klimatehnik.si

Industro Clean
1490 Zeiss Road
Lazer Park
Honeydew
South Africa 2125
Ph: [phone]
Fax: [phone]
Web: www.industroclean.co.za

TML International Ltd
Woodlands
Copmanthorpe Grange
Copmanthorpe
York Y023 3TN
United Kingdom
Ph: [phone]
Fax: [phone]
Web: www.tmlint.com

TTI Floorcare North America
7005 Cochran Road
Glenwillow, OH 44139
United States of America
Ph: [phone]
Fax: [phone]
Web: http://ttioorcare.com 

Pacvac Pty Ltd
182 Daly Street, BELMONT, 6104
WESTERN AUSTRALIA, AUSTRALIA
Ph: + 61 8 9479 1444
Fax: + 61 8 9478 5444
Email: [email protected]
Web: www.pacvac.com
22


Support: 08 9479 1444 25

24
