PADAUK PDK5S-P-003 User manual

6F-6, No.1, Sec. 3, Gongdao 5th Rd., Hsinchu City 30069, Taiwan, R.O.C.
TEL: [phone] www.padauk.com.tw
PDK5S-P-003
Program Writer
User Manual
Version 0.06 – October 30,2018
Copyright 2018 by PADAUK Technology Co., Ltd., all rights reserved.

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 2 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
IMPORTATNT STATEMENT
PADAUK Technology reserves the right to make changes to its products or to terminate
production of its products at any time without notice. Customers are strongly
recommended to contact PADAUK Technology for the latest information and verify whether
the information is correct and complete before placing orders.
PADAUK Technology products are not warranted to be suitable for use in life-support
applications or other critical applications. PADAUK Technology assumes no liability for
such applications. Critical applications include, but are not limited to, those which may
involve potential risks of death, personal injury, fire or severe property damage.
PADAUK Technology assumes no responsibility for any issue caused by a customer’s
product design. Customers should design and verify their products within the ranges
guaranteed by PADAUK Technology. In order to minimize the risks in customers’ products,
customers should design a product with adequate operating safeguards.

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 3 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
Table of Contents
1. About 5S-P-003 Writer ..........................................................................................................5
1.1. The front.................................................................................................................................5
1.2. The back ................................................................................................................................6
1.3. The side face..........................................................................................................................6
1.4. Accessories of Program Writer...............................................................................................7
1.5. Writing application software and User Manual........................................................................7
2. Functional Description.........................................................................................................8
2.1. Steps of loading File...............................................................................................................9
2.2. Blank Check.........................................................................................................................10
2.3. Verify....................................................................................................................................10
2.4. Auto Program.......................................................................................................................10
2.5. Rolling Code..........................................................................................................................11
2.6. Read & Search.....................................................................................................................12
2.7. Convert PDK ........................................................................................................................12
3. Version Update ...................................................................................................................13
3.1. Automatic update .................................................................................................................13
3.2. Manual update......................................................................................................................13
4. JUMPER Description..........................................................................................................14
4.1. Examples .............................................................................................................................14
5. Connecting Board Making Description.............................................................................14
5.1. Define the data of exclusive use packaged pin.....................................................................15
5.2. Connecting Board making ....................................................................................................16
5.3. Case 1..................................................................................................................................16
5.4. Case 2 (Customized package pin)........................................................................................18
5.5. The way to add package pin information to PDK file.............................................................21
5.6. The description of package setting details............................................................................22
6. Semi-automatic Writing Handler Connection Description..............................................23
7. Set O/S Test and Blank Check...........................................................................................23
8. Writer LCM Information and Buzzer Sound Table ...........................................................24
9. Appendix Descriptions.......................................................................................................25
9.1 The difference between 5S-P-003 and 3S-P-002.......................................................................25
9.2 Special notes of MTP On-board writing......................................................................................26
9.3 Special notes of voltage while On-board or Multi-Chip-IC writing (OTP / MTP) ..........................27

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 4 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
Revision History:
Revision Date Description
0.00 2016/07/20 1st version
0.01 2016/08/15 Modify explanation of making the Connecting Board
0.02 2016/09/13 1. Update typesetting
2. Add explanation of 4.1 JUMPER
0.03 2017/06/13 1. Add new description of Buzzer sound
0.04 2017/11/24
1. Update partial pictures
2. Amend 2.6 Read & Search
3. Add section 2.7 Convert PDK
4. Amend chapter 4
5. Update the LCM signal table of chapter 7
6. Add 8.2 On-line writing
0.05 2018/03/19
1. Update the address and telephone number of PADAUK Technology co., Ltd.
2. Update Partial pictures
3. Add description of O/S check or Blank check
4. Update and add the description of MTP On-line (On-board) writing
0.06 2018/10/30 1. Add section 9.3 Special notes of voltage while On-board or Multi-Chip-IC
writing (OTP / MTP)

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 5 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
1. About 5S-P-003 Writer
1.1. The front
(1) USB interface: Connect to PC.
(2) Power interface: Please use the exclusive power converter of Program Writer accessories. (Do not use other
power converters to avoid damaging the Program Writer)
(3) Power Switch: OFF/ON.
(4) Buzzer: Be used as alarm while failed to write.
(5) LED (OK & NG) lamp: Display the result of writing.
(6) LCM displayer: Display the information and result of writing.
(7) Program button: Start writing.
(8) Textool: Suitable for DIP package (available for 28 PIN at most).

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 6 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
1.2. The back
(1) JUMPER (JP1~JP16): Different IC or package would coordinate with different JUMPER position. Please
refer to chapter 4.
(2) JUMPER (JP7): When it comes to non-standard or unusual package, you need to use JP7 to transform
relevant information. About Connecting Board making, please refer to chapter 5.
(3) Forced update mode button: Forcing update the current version, please refer to section 3.1
1.3. The side face
(1) USB interface: Connect to PC.
(2) Power interface: Please use the exclusive power converter of Program Writer. (Do not use other power
converters to avoid damaging the Program Writer)
(3) Power Switch: OFF/ON.
(4) Semi-automatic writing connection port: About the connection method, please refer to chapter 6.

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 7 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
1.4. Accessories of Program Writer
(1) The exclusive power converter.
(2) The USB cable.
1.5. Writing application software and User Manual
You can download the latest version of the application software at the following address (including the latest
version of the Program Writer)
http://www.padauk.com.tw/en/technical/index.aspx?kind=27
Or enter the home page of www.paduak.com.tw, obtain latest Program Writer version from home page >
technology application > technology development tool > Program Writer.Please refer to the chapter 3.

©Copyright 2018, PADAUK Technology Co. Ltd
Page 8 of 27
PDK-5S-P-003-UM-EN-V005 – Mar. 19, 2018
2. Functional Description
(A) Engineering type
(B) Simple type
No matter simple type or engineering type, they have the equal corresponding function.

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 9 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
2.1. Steps of loading File
(1) Load PDK file from PC to Program Writer.
(2) Related information of PDK file would be displayed after loading successfully. (i.e. Check Sum, file name …)
(3) After loading successfully, the JUMPER position and IC placement would be prompted.
(4) The LCM also displays the messages and prompts synchronously.
(5) Users could also unplug the USB cable and write in alone mode after the file loaded successfully.
(6) Users should make sure that JUMPER & IC had been put in the correct position before starting 『Blank
Check』、『Verify』、『Read & Search』and『Auto Program』actions.
(7) About JUMPER & IC placement position, please refer to 『JUMPER Description』.
(8) When JUMPER & IC have been placed, the Program Writer’s LCM displays "IC ready".

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 10 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
2.2. Blank Check
Check whether the IC content is blank or not.
2.3. Verify
Check whether the IC and the .PDK file have the same content.
2.4. Auto Program
Start writing automatically.
It is equal to press the Program Writer’s PROGRAM button.
The actions include: Programmable check Program Verify Protect and so on.
When write successfully, the Program Writer displays 『<<< IC O.K. >>>』on the LCM.
Examples of writing (including the position of JUMPER and IC placement).
Take the follow PDK file and IC for examples.
File IC Jumper IC Shift Note
JP2_83K.PDK PMS131-DIP16 JP2 4
(1) Click on 『Load File』
(2) Choose JP2_83K.PDK, click on 『打开』

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 11 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
(3) Confirm Download OK (notice the message)
(4) Confirm the information displayed on LCM.
(5) Insert JUMPER into JP2 according to the information of (3) or (4).
(6) Place IC according to the information of (3) or (4).『IC Shift: 4』- means shift four blank space from the top.
(7) Make sure the information 『IC Ready』displayed on LCM.
(8) Click on『Auto Program』to start writing.
(9) Make sure the writing result is『PASS』
(10) Make sure the information 『<<< IC O.K. >>>』displayed on LCM.
2.5. Rolling Code
Start the relevant settings about Rolling Code, settings include:
(1) Initial value.
(2) Incremental value.
This function only valid while the Rolling Code grammar has been set in the loading PDK file

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 12 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
Please refer to the IDE User Manual to learn about the ways of setting Rolling Code.
(1) Click on『Application Note』
(2) Click on『IC introduction』『ROM distribution』『Roll_Code』.
(3) Look up the ways of Rolling Code.
2.6. Read & Search
Search for PC’s PDK file which has the same CHECK-SUM.
2.7. Convert PDK
(1) Confirm the PDK file is the one need to convert.
(2) Start converting PDK file.

©Copyright 2018, PADAUK Technology Co. Ltd
Page 13 of 27
PDK-5S-P-003-UM-EN-V005 – Mar. 19, 2018
3. Version Update
You can download the latest version of the application software and Manual (including the latest version of the
Program Writer) at the following address:
http://www.padauk.com.tw/en/technical/index.aspx?kind=27
Or by www.paduak.com.tw website home page > technology application > technology development tool >
Program Writer obtains.
After download the application software, you can install it. Then, you should make sure the Program Writer is
connected to PC when update its version. Besides, the Program Writer will update automatically at the first
execution.
3.1. Automatic update
While execute the application software, the auto-updating application software including the Program Writer
version.
-
(1) The prompting of Program Writer version update
(2) Click on 『OK』to start updating
(3) Download the new version in Program Writer.
(4) Verify the new version.
(5) Connect to PC automatically after finish
NOTICE: Please update manually if there is no auto- update when the first time to execute the application
software.
3.2. Manual update
(1) Press on forced update mode button.
(2) Restart power and enter Boot loader mode. The LCM displays the following information:
(3) Execute the application software and forcing update the Program Writer version included by application
software.

©Copyright 2018, PADAUK Technology Co. Ltd Page 14 of 27 PDK-5S-P-003-UM_CN_V005 – Jun. 19, 2018
X 『no shifts』
4. JUMPER Description
4.1. Examples
After PDK file is loaded to Program Writer, the window displays the IC’s information concerning Jumper position
and the number of needed spaces. As shown in the following picture: (Take PMS154B as an example)
SOP16/DIP16 standard package: Jumper is placed in "JP2" position which on the back of Writer and IC is
placed in Textool (no shifts). As shown in the following pictures:
SOP14 standard package: Jumper is placed in "JP2" position which on the back of Writer; IC is placed from
the second space of Textool. As shown in the following pictures:
Note: As for non-standard and unusual IC package,need be connected to JP7 through Connecting Board.
Please refer to『Connecting Board Making』to learn about Connecting Board. .
5. Connecting Board Making Description
JP7 can support various customizing package pin based on Connecting Board.
The making and rules of the Connecting Board as follows:
(1) Define the information of package pin in program.
(2) Make the Connecting Board.
(3) For developed PDK files, adding the information of package pin please refer to section 5.5.
Shift 1 『Shift one
space from the top』

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 15 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
5.1. Define the data of exclusive use packaged pin
Define the data of exclusive use packaged pin in program. Here is grammar:
.writer package …., (A total of twelve sets of values)
For example: .writer package 16, 5, 11, 9, 10, 8, 7, 6, 14, 0x00F0, 0x00F4, 0.
Grammar instruction
Group
Count Name Introduction Remarks
1
Pin
Count
(the number of pin) Up to 28 pins
2
VDD
VDD pin number
3
PA0
PA0 pin number
Note 1
4
PA3
PA3 pin number
5
PA4
PA4 pin number
6
PA5
PA5pin number
7
PA6
PA6 pin number
8
PA7
PA7 pin number
Note 1
9
GND
GND pin number
10 Mask1
Package the left pin mas
k value,
each bit represents a pin
BIT01st pin, BIT22nd pin,
BITn (n=0..13) 0/1: bypass/ O/S
test
Set 0:this pin not do O/S test
Set 1:this pin do O/S test
Note 2
11 Mask2
Package the right pin mask value,
each bit represents a pin;
BIT0m pin, BIT2(m-1)pin,
BITn (n=0..13) 0/1: bypass/ O/S
test
Set 0:this pin not do O/S test
Set 1:this pin do O/S test
m: The number of pin
Note 2
12 Shift
IC is corresponding to the blank
space number need to shift from the
top of SOCKET.
Note 1: If the pin does not exist, fill in 32 representing NC (no connect)
Note 2: If the pin does not exist or cannot do O/S test (i.e. Special multi-chip package pin), set the
corresponding bit value to zero.

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 16 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
5.2. Connecting Board making
The JP7 last 8 pins are writing pins, as shown in the following figure:
While making a Connecting Board, please decide the IC placement position (generally assumed that the first pin
of IC is aligned with the upper left first pin of the Socket.) and connect the last 8 pins of Connecting Board with
the corresponding pin of IC, as shown in the following figure:
5.3. Case 1
Take PMx131 MSOP-10 for example:
IC Package Jumper IC Shift Note
PMx131 MSOP10 JP7 Please connect JP7 with
Connecting Board.(Note1)
The PMx131 MSOP-10 package as follows:

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 17 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
1. You can use the following instruction to define the exclusive package pin:
.writer package 10, 1, 9, 7, 8, 3, 2, 32, 10, 0x003F, 0x003F, 4
Group
count
Name Description Value Remarks
1 Pin
Count
The number of
package pin
10
2 VDD VDD pin serial number 1
3 PA0 PA0 pin serial number 9
4 PA3 PA3pin serial number 7
5 PA4 PA4pin serial number 8
6 PA5 PA5pin serial number 3
7 PA6 PA6 pin serial number 2
8 PA7 PA7 pin serial number 32 32 indicates that PA7 does not exist
9 GND GND pin serial number 10
10 Mask1 Package the left pin
mask value
0x003F All pin should test O/S.
11 Mask2 Package the right pin
mask value
0x003F All pin should test O/S.
12 Shift The blank space IC
need to be shifted
4 IC first pin align to the upper left fifth
pin of Socket
2. Make the Connecting Board

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 18 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
(1) Confirm the package pin of PMx131 MSOP-10
(2) Confirm the JP7 pin in the back of Writer
TA16-PA3 TB16-PA0
TA17-PA4 TB17-PA7
TA18-PA5 TB18-PA6
TA19-GND TB19-VDD
(3) Put IC in SOCKET put IC from the fifth space of SOCKET
According to the data below, connecting『VDD、GND、PA0、PA3、PA4、PA6、PA7』with IC’s corresponding
pins.
TA16 (PA3) ----------TB7(IC-PA3)
TA17 (PA4) ----------TB6(IC-PA4)
TA18 (PA5) ----------TA6(IC-PA5)
TA19 (GND) ----------TB4(IC-GND)
TB16 (PA0) ----------TB5(IC-PA0)
TB17 (PA7) ----------NC
TB18 (PA6) ----------TA5(IC-PA6)
TB19 (VDD) ----------TA4(IC-VDD)
NOTICE: If the thirteenth group number (shift) is changed to 0, it means that the first pin of IC aligns the upper
left first pin of Socket, at the same time all connection of corresponding IC pins have to be changed.
5.4. Case 2 (Customized package pin)
Customized package pins are shown in the following picture:

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 19 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
1. You can use the following instruction to define the exclusive package pin:
.writer package 16, 6, 12, 10, 11, 9, 8, 7, 16, 0x00FC, 0x00F1, 0
Group
Count Name Description Value Remark
1 Pin Count the number of pin 16
2 VDD VDD pin serial number 6
3 PA0 PA0pin serial number 12
4 PA3 PA3pin serial number 10
5 PA4 PA4 pin serial number 11
6 PA5 PA5 pin serial number 9
7 PA6 PA6 serial number 8
8 PA7 PA7 pin serial number 7
9 GND GND pin serial number 16
10 Mask1 Package the left pin
mask value 0x00FC Bypass pin 1, 2.
11 Mask2 Package the right pin
mask value 0x00F1 Bypass pin 15, 14, 13
12 Shift The blank space IC
need to be shifted 0 The first pin of IC aligns the upper left
first pin of Socket

PDK 5S-P-003
Program Writer
©Copyright 2018, PADAUK Technology Co. Ltd
Page 20 of 27
PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018
(1) Confirm the package pins.
(2) Confirm the JP7 pins on the back of Writer (TA16~TA19, TB16~TB19).
TA16-PA3 TB16-PA0
TA17-PA4 TB17-PA7
TA18-PA5 TB18-PA6
TA19-GND TB19-VDD
(3) Put IC in the SOCKET put IC from the top of Socket (no space).
According to the following table ,complete the connection between『VDD、GND、PA0、PA3、PA4、PA6、
PA7』and IC’s corresponding pins.
TA16 (PA3) ----------TB6(IC-PA3)
TA17 (PA4) ----------TB7(IC-PA4)
TA18 (PA5) ----------TA6(IC-PA5)
TA19 (GND) ----------TB0(IC-GND)
TB16 (PA0) ----------TB4(IC-PA0)
TB17 (PA7) ----------TA6(IC-PA7)
TB18 (PA6) ----------TA7(IC-PA6)
TB19 (VDD) ----------TA5(IC-VDD)