paladin Bradco VRS48 Product manual

10380 7-22-13-6
800-456-7100 I www.paladinattachments.com 503 Gay Street, Delhi, IA 52223, United States of America Copyright ©
OPERATOR’S AND PARTS MANUAL
VIBRATORY ROLLER
SERIAL NUMBER: ___________________ Manual Number: OM695
Part Number: 75595
MODEL NUMBER: ___________________ Rev. 4

TABLE OF CONTENTS
10419 9-28-05
PREFACE ..........................................................................................................................................................3
SAFETY PRECAUTIONS
SAFETY STATEMENTS ........................................................................................................................... 5
GENERAL SAFETY PRECAUTIONS....................................................................................................5-7
EQUIPMENT SAFETY PRECAUTIONS ..................................................................................................8
DECALS
DECAL PLACEMENT............................................................................................................................... 9
DECALS ............................................................................................................................................10-11
INSTALLATION
GENERAL INFORMATION..................................................................................................................... 12
NOMENCLATURE..................................................................................................................................12
ATTAChING ...........................................................................................................................................12
DETAChING...........................................................................................................................................13
OPERATINg INSTRUCTIONS
GENERAL INFORMATION..................................................................................................................... 14
OPERATING PROCEDURE...................................................................................................................14
mAINTENANCE AND SERVICE
GENERAL MAINTENANCE - EvERY 8 / 100 / 500 hOURS ..........................................................15-16
ChANGING GEAR LUBE.......................................................................................................................16
DRUM REMOvAL...................................................................................................................................16
DRUM INSTALLATION...........................................................................................................................17
REPLACING vIBRATION ISOLATORS ............................................................................................17-18
REPLACING LEFT BEARINGS AND/OR hUBS...............................................................................18-19
REPLACING RIGhT BEARINGS AND/OR hUBS ............................................................................20-21
hYDRAULIC MOTOR REPLACEMENT.................................................................................................21
TROUBLEShOOTINg................................................................................................................................. 22
SPECIFICATIONS
BOLT TORQUE SPECIFICATIONS........................................................................................................23
vIBRATORY ROLLER SPECIFICATIONS .............................................................................................24
LImITED wARRANTY .................................................................................................................................25
PARTS
SMOOTh vIBRATORY ROLLER ASSEMBLIES ..............................................................................26-27
PADDED vIBRATORY ROLLER ASSEMBLIES ...............................................................................28-29
SPRING CLAMP ASSEMBLY............................................................................................................30-31
FRAME ASSEMBLIES ......................................................................................................................32-33
SMOOTh DRUM ASSEMBLIES .......................................................................................................34-35
PADDED DRUM ASSEMBLIES ........................................................................................................36-37
hUB ASSEMBLIES ...........................................................................................................................38-39
hYDRAULIC ASSEMBLY..................................................................................................................40-41
75595
1

THIS PAGE
IS INTENTIONALLY
BLANK
2
75595

PREFACE
10344 7-31-13-4
GENERAL COMMENTS
Congratulations on the purchase of your new BRADCO product! This product was carefully
designed and manufactured to give you many years of dependable service. Only minor mainte-
nance (such as cleaning and lubricating) is required to keep it in top working condition. Be sure
to observe all maintenance procedures and safety precautions in this manual and on any safety
decals located on the product and on any equipment on which the attachment is mounted.
This manual has been designed to help you do a better, safer job. Read this manual care-
fully and become familiar with its contents.
WARNING! Never let anyone operate this unit without reading the "Safety Precautions"
and "Operating Instructions" sections of this manual.
Always choose hard, level ground to park the vehicle on and set the brake
so the unit cannot roll.
Unless noted otherwise, right and left sides are determined from the operator’s control posi-
tion when facing the attachment.
NOTE: The illustrations and data used in this manual were current (according to the infor-
mation available to us) at the time of printing, however, we reserve the right to redesign and
change the attachment as may be necessary without notication.
BEFORE OPERATION
The primary responsibility for safety with this equipment falls to the operator. Make sure the
equipment is operated only by trained individuals that have read and understand this manual. If
there is any portion of this manual or function you do not understand, contact your local authorized
dealer or the manufacturer to obtain further assistance. Keep this manual available for reference.
Provide the manual to any new owners and/or operators.
SAFETY ALERT SYMBOL
This is the “Safety Alert Symbol” used by this industry. This symbol is used to warn
of possible injury. Be sure to read all warnings carefully. They are included for your
safety and for the safety of others working with you.
SERVICE
Use only manufacturer replacement parts. Substitute parts may not meet the required stan-
dards.
Record the model and serial number of your unit on the cover of this manual. The parts
department needs this information to insure that you receive the correct parts.
SOUND AND VIBRATION
Sound pressure levels and vibration data for this attachment are inuenced by many different param-
eters: some items are listed below (not inclusive):
• prime mover type, age, condition, with or without cab enclosure and conguration
• operator training, behavior, stress level
• job site organization, working material condition, environment
Based on the uncertainty of the prime mover, operator, and job site, it is not possible to get precise ma-
chine and operator sound pressure levels or vibration levels for this attachment.
NOTE:A list of all Paladin Patents can be found at http://www.paladinattachments.com/patents.asp.
75595
3

THIS PAGE
IS INTENTIONALLY
BLANK
4
75595

10338 8-16-05
SAFETY STATEMENTS
DANGER
GENERAL SAFETY PRECAUTIONS
WARNING! READ MANUAL PRIOR TO INSTALLATION
Improper installation, operation, or maintenance of this equipment could result in
serious injury or death. Operators and maintenance personnel should read this man-
ual, as well as all manuals related to this equipment and the prime mover thoroughly
before beginning installation, operation, or maintenance. FOLLOW ALL SAFETY
INSTRUCTIONS IN THIS MANUAL AND THE PRIME MOVER’S MANUAL(S).
READ AND UNDERSTAND ALL SAFETY STATEMENTS
Read all safety decals and safety statements in all manuals prior to operating or
working on this equipment. Know and obey all OSHA regulations, local laws, and
other professional guidelines for your operation. Know and follow good work
practices when assembling, maintaining, repairing, mounting, removing, or operating
this equipment.
KNOW YOUR EQUIPMENT
Know your equipment’s capabilities, dimensions, and operations before operating.
Visually inspect your equipment before you start, and never operate equipment that
is not in proper working order with all safety devices intact. Check all hardware to
ensure it is tight. Make certain that all locking pins, latches, and connection devices
are properly installed and secured. Remove and replace any damaged, fatigued, or
excessively worn parts. Make certain all safety decals are in place and are legible.
Keep decals clean, and replace them if they become worn or hard to read.
WARNING
CAUTION
THIS SIGNAL WORD IS USED WHERE SERIOUS INJURY OR DEATH
WILL RESULT IF THE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY.
THIS SIGNAL WORD IS USED WHERE SERIOUS INJURY OR DEATH
COULD RESULT IF THE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY.
THIS SIGNAL WORD IS USED WHERE MINOR INJURY COULD RESULT IF
THE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY.
NOTICE INDICATES A PROPERTY DAMAGE MESSAGE.
NOTICE
THIS SYMBOL BY ITSELF OR WITH A WARNING WORD THROUGHOUT THIS MAN-
UAL IS USED TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR
PERSONAL SAFETY OR THE SAFETY OF OTHERS. FAILURE TO FOLLOW THESE
INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.
75595
5

GENERAL SAFETY PRECAUTIONS
WARNING! PROTECT AGAINST FLYING DEBRIS
Always wear proper safety glasses, goggles, or a face shield when driving pins in or
out, or when any operation causes dust, ying debris, or any other hazardous mate-
rial.
WARNING! LOWER OR SUPPORT RAISED EQUIPMENT
Do not work under raised booms without supporting them. Do not use support mate-
rial made of concrete blocks, logs, buckets, barrels, or any other material that could
suddenly collapse or shift positions. Make sure support material is solid, not de-
cayed, warped, twisted, or tapered. Lower booms to ground level or on blocks. Lower
booms and attachments to the ground before leaving the cab or operator’s station.
WARNING! USE CARE WITH HYDRAULIC FLUID PRESSURE
Hydraulic uid under pressure can penetrate the skin and cause serious injury or
death. Hydraulic leaks under pressure may not be visible. Before connecting or dis-
connecting hydraulic hoses, read your prime mover’s operator’s manual for detailed
instructions on connecting and disconnecting hydraulic hoses or ttings.
•Keep unprotected body parts, such as face, eyes, and arms as far away as
possible from a suspected leak. Flesh injected with hydraulic uid may develop
gangrene or other permanent disabilities.
• If injured by injected uid, see a doctor at once. If your doctor is not familiar with
this type of injury, ask him to research it immediately to determine proper treat-
ment.
• Wear safety glasses, protective clothing, and use a piece of cardboard or wood
when searching for hydraulic leaks. DO NOT USE YOUR HANDS!
SEE ILLUSTRATION.
CARDBOARD
HYDRAULIC HOSE
OR FITTING
MAGNIFYING GLASS
10339 8-16-05
6
75595

GENERAL SAFETY PRECAUTIONS
10340 8-16-05
WARNING! DO NOT MODIFY MACHINE OR ATTACHMENTS
Modications may weaken the integrity of the attachment and may impair the func-
tion, safety, life, and performance of the attachment. When making repairs, use only
the manufacturer’s genuine parts, following authorized instructions. Other parts may
be substandard in t and quality. Never modify any ROPS (Roll Over Protection
Structure) or FOPS (Falling Object Protective Structure) equipment or device. Any
modications must be authorized in writing by the manufacturer.
WARNING! SAFELY MAINTAIN AND REPAIR EQUIPMENT
•Do not wear loose clothing or any accessories that can catch in moving parts. If
you have long hair, cover or secure it so that it does not become entangled in the
equipment.
• Work on a level surface in a well-lit area.
• Use properly grounded electrical outlets and tools.
• Use the correct tools for the job at hand. Make sure they are in good condition for
the task required.
• Wear the protective equipment specied by the tool manufacturer.
SAFELY OPERATE EQUIPMENT
Do not operate equipment until you are completely trained by a qualied operator
in how to use the controls, know its capabilities, dimensions, and all safety require-
ments. See your machine’s manual for these instructions.
•Keep all step plates, grab bars, pedals, and controls free of dirt, grease, debris,
and oil.
• Never allow anyone to be around the equipment when it is operating.
• Do not allow riders on the attachment or the prime mover.
• Do not operate the equipment from anywhere other than the correct operator’s
position.
• Never leave equipment unattended with the engine running, or with this attach-
ment in a raised position.
• Do not alter or remove any safety feature from the prime mover or this attach-
ment.
• Know your work site safety rules as well as trafc rules and ow. When in doubt
on any safety issue, contact your supervisor or safety coordinator for an explana-
tion.
75595
7

EQUIPMENT SAFETY PRECAUTIONS
WARNING! KNOW WHERE UTILITIES ARE
Observe overhead electrical and other utility lines. Be sure equipment will clear
them. When digging, call your local utilities for location of buried utility lines, gas,
water, and sewer, as well as any other hazard you may encounter.
OPERATING THE VIBRATORY ROLLER
Block off work area from bystanders, livestock, etc.
Operate only from the operator’s station.
Do not lift loads in excess of the capacity of the prime mover.
When operating on slopes, drive up and down, not across. Avoid steep hillside
operation, which could cause the prime mover to overturn.
Reduce speed when driving over rough terrain, on a slope, or turning, to avoid
overturning the vehicle.
An operator must not use drugs or alcohol, which can change his or her alert-
ness or coordination. An operator taking prescription or over-the-counter drugs
should seek medical advice on whether or not he or she can safely operate
equipment.
Before exiting the prime mover, lower the attachment to the ground, turn off the
prime mover’s engine, remove the key and apply the brakes.
TRANSPORTING THE VIBRATORY ROLLER
Travel only with the attachment in a safe transport position to prevent uncon-
trolled movement. Drive slowly over rough ground and on slopes.
When driving on public roads use safety lights, reectors, Slow Moving Vehicle
signs etc., to prevent accidents. Check local government regulations that may
affect you.
Do not drive close to ditches, excavations, etc., cave in could result.
Do not smoke when refueling the prime mover. Allow room in the gas tank for
expansion. Wipe up any spilled fuel. Secure cap tightly when done.
MAINTAINING THE VIBRATORY ROLLER
Before performing maintenance, lower the attachment to the ground, turn off the
engine, remove the key and apply the brakes.
Never perform any work on the attachment unless you are authorized and quali-
ed to do so. Always read the operator service manual’s before any repair is
made. After completing maintenance or repair, check for correct functioning of
the attachment. If not functioning properly, always tag “DO NOT OPERATE” until
all problems are corrected.
Worn, damaged, or illegible safety decals must be replaced. New safety decals
can be ordered from BRADCO.
Never make hydraulic repairs while the system is under pressure. Serious per-
sonal injury or death could result.
Never work under a raised attachment.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
10381 9-12-05
8
75595

DECALS
10399 9-16-05
DECAL PLACEMENT
GENERAL INFORMATION
The diagram on this page shows the location of the decals used on the BRADCO Vibra-
tory Roller. The decals are identied by their part numbers, with reductions of he actual decals
located on the following pages. Use this information to order replacements for lost or damaged
decals. Be sure to read all decals before operating the attachment. They contain information
you need to know for both safety and longevity.
IMPORTANT: Keep all safety signs clean and legible. Replace all missing, illegible, or dam-
aged safety signs. When replacing parts with safety signs attached, the safety signs must also
be replaced.
REPLACING SAFETY SIGNS: Clean the area of application with nonammable solvent, then
wash the same area with soap and water. Allow the surface to fully dry. Remove the back-
ing from the safety sign, exposing the adhesive surface. Apply the safety sign to the position
shown in the diagram above and smooth out any bubbles.
LOGO
#40149
#4468
#40678
#40150
SERIAL
NuMbER TAG
LOCATION
#40151
#40590
#4338
#4468
LOGO
MODEL NuMbER
#40149
75595
9

DECALS
10400 9-16-05
BRADCO LOGO
PART #40113 (SMALL - WHITE)
PART #40092 (LARGE - WHITE)
VRS48
MODEL NUMBER
PART #40892
VRS66
MODEL NUMBER
PART #40893
VRS73
MODEL NUMBER
PART #40894
VRS84
MODEL NUMBER
PART #40895
VRP48
MODEL NUMBER
PART #40896
VRP66
MODEL NUMBER
PART #40897
VRP73
MODEL NUMBER
PART #40898
VRP84
MODEL NUMBER
PART #40899
MADE IN U.S.A.
PART #4338
MADE IN U.S.A.
WARNING! BEFORE LEAVING SEAT
PART #40678
CAUTION! HIGH FLOW SYSTEMS
PART #40590
10
75595

DECALS
10401 9-16-05
WARNING! HIGH PRESSURE FLUID
PART #40151
WARNING! READ MANUAL
PART #40150
WARNING! FOOT CRUSH
PART #4468
DANGER! PINCH POINT
PART #40149
75595
11

INSTALLATION
10382 9-27-05
GENERAL INFORMATION
The BRADCO Vibratory Rollers were designed to be easy to use and maintain. They
are operated by the loaders auxiliary hydraulics. The Vibratory Rollers mount to the toolbar /
quick attach mechanism for easy mounting.
NOTICE: DO NOT operate the Vibratory Rollers on a Hi-Flow hydraulic system (25
GPM Maximum). Damage to the hydraulic motor will occur.
NOMENCLATURE
Throughout this manual, reference is made to various Vibratory Roller components.
Study the following diagram to acquaint yourself with the various names of these components.
This knowledge will be helpful when reading through this manual or when ordering service
parts. There is a complete parts breakdown for each roller at the back of this manual.
SCRAPER PLATES
POWER & RETURN HOSES
HYDRAULIC
MOTOR
HITCH FRAME
SPRING CLAMP ASSEMBLY
FRAME
DRUM
(SMOOTH SHOWN)
MOTOR GUARD
RELIEF VALVE
ATTACHING
Install the Vibratory Roller by following your power unit operator’s manual for proper
installion of an attachment. Connect the power and return hoses to the auxiliary hydraulic cou-
plers on the loader. IMPORTANT: All hose routings should be check for kinks or pinching.
Reroute if necessary.
WARNING! To Avoid Serious Personal Injury, make sure the Vibratory Roller is securely
latched to the attachment mechanism of your unit. Failure to do so could
result in separation of the attachment from the unit.
12
75595

INSTALLATION
10383 9-27-05
DETACHING
 Onrm,levelground.Lowertheliftarmsagainsttheframeandplacetherolleronthe
ground.
Move the control levers back and forth to relieve pressure in the line. Disconnect cou-
plers.
NOTE: Connect couplers together or install dust caps and plugs to prevent contami-
nants from entering the hydraulic system.
Follow your power unit operator’s manual for detaching (removing) an attachment.
CAUTION! Block vibratory roller drum to prevent rolling when not attached to loader.
NOTE: Frequent lubrication of grease ttings with a multi-purpose grease will greatly
increase the life of the product.
IMPORTANT: DISENGAGE THE AUXILIARY HYDRAULICS, STOP THE ENGINE, ENGAGE
PARKING BRAKE AND REMOVE KEY BEFORE LEAVING THE OPERATOR’S STATION.
75595
13

OPERATION
10384 9-250-05
GENERAL INFORMATION
The BRADCO Vibratory Roller is a hydraulically powered attachment designed to com-
pact soil, stone or ll material. Performance of the roller varies greatly depending on the op-
erator and how the attachment is used.
WARNING! Read and understand the Safety Precautions section of this manual before
beginning operation.
Operate the attachment only from the operator’s station. Any other method
could result in serious personal injury or death.
Do not allow bystanders in the area when operating.
Go up and down slopes, not across them. Keep the heavy end of the ma-
chine uphill.
Follow mandatory safety shutdown procedures before cleaning, adjusting,
lubricating or servicing this attachment.
OPERATING PROCEDURE
1. Position the Vibratory Roller in the desired starting location and lower the attachment to
the ground.
2. Lower the loader arms and roll the toolbar out until the top of the roller frame is paral-
lel to the ground and the front tires of the loader are approximately 1-3 inches off the
ground.
3. Engage the auxiliary hydraulics on the loader and slowly drive forward.
4. Once you have reached the end of the pass, reverse the skid steer and drive slowly
backwards to further pack the soil and cover any tire tracks.
IMPORTANT: The drive circuit is bi-directional but, for the best results it is recommend-
ed that you reverse the auxiliary hydraulic ow when you reverse direction.
NOTICE: DO NOT operate the Vibratory Roller on Hi-Flow hydraulic systems (25 GPM
maximum). Damage to the hydraulic motor will occur.
14
75595

MAINTENANCE AND SERVICE
10385 9-27-05
GENERAL INFORMATION
Regular maintenance and service is the key to long equipment life and safe operation.
Maintenance requirements have been kept to a minimum. However it is important that these
maintenance procedures be performed as described in this section.
WARNING! Read the Safety Precautions section of this manual before performing any
maintenance procedure.
Follow all mandatory safety shutdown procedures outlined in the loader
operator’s manual before adjusting, cleaning, lubricating or servicing this
attachment.
EVERY 8 HOURS
Lubricate all grease ttings. (One grease tting located on the back of the hitch frame).
Check bolts for tightness.
Check hydraulic hoses for leaks, pinching or deterioration.
Check all safety signs are clean and legible.
Replace any damaged or worn parts.
WARNING! Escaping hydraulic uid under pressure can have sufcient force to pen-
etrate the skin causing serious personal injury. Fluid escaping from a very
small hole can be almost invisible. Use a piece of cardboard or wood rather
than your hands to search for suspected leaks.
Keep unprotected body parts, such as face, eyes, and arms as far away
as possible from a suspected leak. Flesh injected with hydraulic uid may
develop gangrene or other permanent disabilities.
If injured by injected uid see a doctor at once. If your doctor is not famil-
iar with this type of injury, ask him to research it immediately to determine
proper treatment.
CARDBOARD
HYDRAULIC HOSE
OR FITTING
MAGNIFYING
GLASS
EVERY 100 HOURS
Check oil level in roller shaft. (Remove 90° elbow with ttings in the cover plate. Oil
level is sufcient if oil is up to the ll hole. If the unit is level and the oil is not visible, add as
required.)
NOTE: The Vibratory Roller is a sealed unit. If oil is low, service is required.
75595
15

MAINTENANCE AND SERVICE
10386 4-27-07-2
EVERY 500 HOURS
WARNING! Follow all mandatory safety shutdown procedures outlined in the loader
operator’s manual before adjusting, cleaning, lubricating or servicing this
attachment.
The gear oil in the drive circuit must be changed after every 500 hours of operation with
an 80-90 weight gear lube.
TO CHANGE GEAR LUBE:
1. Raise the left side (motor side) of the vibratory roller using a hoist and place a 6” x 6”
block under the drum and lower the roller onto the block.
2. On the right side of the vibratory roller, place a container (to catch the oil) under the
cover plate and remove the cover plate leaving all ttings in place.
3. Once the oil has been completely drained from the roller shaft, remove the block from
the left side of the vibratory roller and place under the right side of the roller.
4. Clean the existing silicone from the cover plate and reseal and replace using new adhe-
sive sealant (100% Silicone Rubber). Check for leaks.
5. Remove the breather plug from the cover plate and ll the roller shaft with the amount
of 80-90 weight gear lube recommended for your attachment. (See Oil Requirements
below.) Replace breather plug with breather pointing up.
OIL REQUIREMENTS (APPROXIMATE)
48” Vibratory Roller = 1.38 Quarts
66” Vibratory Roller = 2.00 Quarts
73” Vibratory Roller = 2.13 Quarts
84” Vibratory Roller = 2.50 Quarts
DRUM REMOVAL
NOTE: Removal of the isolator bolts will allow the vibratory roller frame to fall. Make
sure the frame is completely supported before removing.
WARNING! NEVER place hands or ngers between the frame and drum assemblies
during installation or removal. Severe personal injury could occur.
WARNING! Follow all mandatory safety shutdown procedures outlined in the loader
operator’s manual before adjusting, cleaning, lubricating or servicing this
attachment.
1. Using a loader or hoist, position the unit with the drum on the ground and the frame
completely supported on blocks. Remove the motor guard and the motor bolts. Place a
container (to catch the oil from the roller shaft) under the motor and remove the motor
from the drum assembly. See Figure #1
16
75595

MAINTENANCE AND SERVICE
10387 4-9-10-3
2. Remove the twelve (isolator) bolts securing the roller frame to the drum and isolators.
Using the loader or hoist, lift the frame assembly off of the drum assembly and set
aside. See Figure #1
3. Use a hoist to nish draining the oil from the roller shaft. Drum removal is complete
DRUM INSTALLATION
1. Lift the roller frame over the top of the drum assembly and into position. Reinstall the
twelve .50” UNC x 1.25” capscrews and hard at washers (using loctite 271 or equiva-
lent) securing the frame to the drum.
WARNING! NEVER place hands or ngers between the frame and drum assemblies
during installation or removal. Severe personal injury could occur.
2. Reinstall the hydraulic motor, gasket and motor guard using the existing hardware (us-
ing loctite 271 or equivalent on motor mounting hardware).
3. Fill the roller shaft with 80-90 weight gear lube by following the procedure listed in TO
CHANGE GEAR LUBE.
REPLACING VIBRATION ISOLATORS (RUBBER MOUNTS)
NOTE: Removal of the isolator bolts will allow the vibratory roller frame to fall. Make
sure the frame is completely supported before removing.
WARNING! Follow all mandatory safety shutdown procedures outlined in the loader
operator’s manual before adjusting, cleaning, lubricating or servicing this
attachment.
MOTOR GUARD
REMOVE MOTOR FROM DRUM
ASSEMBLY
DRUM ASSEMBLY
.50” UNC X 1.25 CAPSCREWS
(ISOLATOR BOLTS)
ISOLATOR’S
(RUBBER MOUNTS)
ROLLER FRAME
FIGURE #1
75595
17

MAINTENANCE AND SERVICE
10388 9-21-05
1. Remove the drum by following the procedure listed for DRUM REMOVAL.
2. Remove the .50” UNC deformed lock nuts securing the isolators to the left and right
hubs and install new isolators. Torque nuts to 55 ft. lbs.
NOTICE: Do NOT remove the hubs from the roller shaft. Removing the hubs without
rst supporting the roller shaft will cause damage to the roller shaft seal sleeves.
3. Install the drum by following the procedure listed for DRUM INSTALLATION.
WARNING! NEVER place hands or ngers between the frame and drum assemblies
during installation or removal. Severe personal injury could occur.
REPLACING LEFT BEARINGS AND/OR HUBS
WARNING! Follow all mandatory safety shutdown procedures outlined in the loader
operator’s manual before adjusting, cleaning, lubricating or servicing this
attachment.
1. Remove the drum by following the proce-
dure listed for DRUM REMOVAL.
2. Remove the bearing spacer, lock washer
and lock nut from the end of the roller
shaft by rst bending back the engaged
tab on the lock washer.
3. Insert a clean .62” rod into the motor end
of the roller shaft and support the shaft in
its current position.
NOTICE: Removing the hubs without rst
supporting the roller shaft will
cause damage to the roller shaft
seal sleeves.
4. Remove the outer bearing hub mounting
bolts and slide both bearing hubs out and
over the end of the rod while keeping the
roller shaft rmly supported.
DRUM
SUPPORT
REMOVE BOTH
HUBS TOGETHER
.62” ROD
ROLLER SHAFT
BEARING SPACER
LOCK WASHER
LOCK NUT
FIGURE #2
18
75595