Palmgren 81091A User manual

operating manual & parts list 81091A
6 x 9″
BELT & DISC SANDER
Read carefully and follow all safety rules and operating instructions before
first use of this product.
25899.09-1130

2
Palmgren Operating Manual & Parts List 81091AA
DESCRIPTION
Palmgren 6” Belt and 9”Disc Sander is constructed of rugged die
cast aluminum and cast iron providing stability and vibration-free
operation.The 6 x 48” belt and 9” diameter disc are used to sand,
deburr, bevel and grind large workpieces of wood, plastic and
metal.
The 6 x 48”belt housing can be pivoted from vertical to horizontal
for sanding large, straight workpieces.The belt assembly includes a
tilting, cast iron table with miter gauge and dust collection chute.
The 9”diameter disc can be used to sand or bevel surfaces with
the use of 0 to 45º scaled aluminum table.The 9”diameter disc
assembly includes a tilting table with miter gauge slot and dust
collection chute.
The 3”diameter idler drum permits the sanding of contoured
shapes and finishes by positioning the adjustable platen from a
horizontal to a vertical position.
The two dust collection chutes with adaptable exhaust ports allow
for quick removal of dust.The adjustable miter gauge can be used
on both the belt and disc tables for guiding the workpiece at a
desired angle while sanding.
UNPACKING
Refer to Figure 1.
Check for shipping damage.If damage has occurred, a claim must
be filed with carrier. Check for completeness. Immediately report
missing parts to dealer.
The sander comes assembled as one unit. Additional parts which
need to be fastened to sander, should be located and accounted
for before assembling.
A Abrasive and aluminum disc with set screw
B Disc guard
C Disc dust chute
D Disc table with attached trunnions
E Work stop
F Belt table assembly
G Belt dust chute
H Miter gauge assembly
Parts bag includes: two handles, three 6-1.0 x 12mm pan head screws,
one 10-1.50 x 25mm socket head bolt, three 10mm flat washers,
four 5-0.8 x 8mm pan head screws and three 6mm lock washers.
SPECIFICATIONS
Belt size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 x 48”
Belt platen area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71/8x 17”
Belt drum dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 x 61/8”
Belt table dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57/8x 913/16”
Belt table tilts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 to 60º
Belt dust chute diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21/2”
Belt speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2700 SFPM
Disc diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9”
Disc table dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57/8x 1113/16”
Disc table tilts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 to 45º
Disc dust chute diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11/2”
Disc speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3450 RPM
Base dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141/2x 141/2”
Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SP, Locking rocker
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 HP, 120/240 V, 9/4.5 Amps
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 lbs
SAFETY RULES
PROPOSITION 65 WARNING: Some dust created by power
sanding, sawing, grinding, drilling and other construction activities
contains chemicals known to the state of California to cause can-
cer, birth defects or other reproductive harm.
Some examples of these chemicals are:
•Lead from lead-based paints.
•Crystalline silica from bricks and cement and other
masonry products.
•Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures vary, depending on how often you
do this type of work.To reduce your exposure to these chemicals:
work in a well ventilated area and work with approved safety
equipment. Always wear OSHA/NIOSH approved, properly fitting
face mask or respirator when using such tools.
WARNING: For your own safety, read all of the instructions and
precautions before operating tool.
CAUTION: Always follow proper operating procedures as defined in
this manual even if you are familiar with use of this or similar tools.
Remember that being careless for even a fraction of a second can
result in severe personal injury.
BE PREPARED FOR JOB
•Wear proper apparel. Do not wear loose clothing, gloves, neck-
ties, rings, bracelets or other jewelry which may get caught in
moving parts of machine.
•Wear protective hair covering to contain long hair.
•Wear safety shoes with non-slip soles.
•Wear safety glasses complying with United States ANSI Z87.1.
Everyday glasses have only impact resistant lenses.They are
NOT safety glasses.
•Wear face mask or dust mask if operation is dusty.
•Be alert and think clearly.Never operate power tools when
tired, intoxicated or when taking medications that cause
drowsiness.
PREPARE WORK AREA FOR JOB
•Keep work area clean. Cluttered work areas and work benches
invite accidents.
•Do not use power tools in dangerous environments. Do not use
power tools in damp or wet locations. Do not expose power
tools to rain.
•Work area should be properly lighted.
•Proper electrical receptacle should be available for tool.
Three-prong plug should be plugged directly into properly
grounded, three-prong receptacle.
•Extension cords should have a grounding prong and the three
wires of the extension cord should be of the correct gauge.
•Keep visitors at a safe distance from work area.
Figure 1 – Unpacking
D
A
BF
E
G
H
C

3
SAFETY RULES (CONTINUED)
•Keep children out of the workplace. Make workshop childproof.
Use padlocks, master switches or remove switch keys to pre-
vent any unauthorized use of power tools.
TOOL SHOULD BE MAINTAINED
•Always unplug tool prior to inspection.
•Consult manual for specific maintaining and adjusting proce-
dures.
•Keep tool lubricated and clean for safest operation.
•Remove adjusting tools. Form habit of checking to see that
adjusting tools are removed before switching machine on.
•Keep all parts in working order. Check to determine that the
guard or other parts will operate properly and perform their
intended function.
•Check for damaged parts. Check for alignment of moving parts,
binding, breakage, mounting and any other condition that may
affect a tool’s operation.
•A guard or other part that is damaged should be properly
repaired or replaced. Do not perform makeshift repairs. (Use
the parts list to order replacement parts.)
KNOW HOW TO USE TOOL
•Use right tool for job. Do not force tool or attachment to do a
job for which it was not designed.
•Disconnect tool from power when changing abrasive belt or
disc.
•Avoid accidental start-up. Make sure that the switch is in the
OFF position before plugging in.
•Do not force tool. It will work most efficiently at the rate for
which it was designed.
•Keep hands away from moving parts and sanding surfaces.
•Never leave tool running unattended.Turn the power off and
do not leave tool until it comes to a complete stop.
•Do not overreach. Keep proper footing and balance.
•Never stand on tool. Serious injury could occur if tool is tipped
or if belt or disc are unintentionally contacted.
•Know your tool. Learn the tool’s operation, application and
specific limitations.
•Handle workpiece correctly. Protect hands from possible injury.
•Turn machine off if it jams. Belt jams when it digs to deeply into
workpiece. (Motor force keeps it stuck in the work).
•Support workpiece with miter gauge, belt platen or work table.
•Maintain 1/16”maximum clearance between table and sanding
belt or disc.
CAUTION: Think safety! Safety is a combination of operator
common sense and alertness at all times when tool is being used.
ASSEMBLY
Refer to Figures 2 and 3.
WARNING: Do not attempt to operate tool until it is completely
assembled according to instructions.
CAUTION: Do not attempt assembly if parts are missing.Use this
manual to order repair parts.
ASSEMBLE DISC TABLE
Refer to Figure 2.
•Attach disc guard to end shield using three pan head screws,
three flat washers and three lock washers.
•Remove tape from key and armature. Slide aluminum disc with
abrasive disc onto armature with keyway in disc aligned with
key in armature. Secure disc to armature using set screw.
•Slide disc dust chute onto disc guard from below the 9” disc
with exhaust port to rear of tool. Secure dust chute to disc
guard with two pan head screws.
•Slide disc table with attached trunnions onto the raised bosses
on each side of disc guard.Mount two handles and flat washers
through trunnions into threaded holes on each side of disc
guard.
•Locate table in desired position and secure with handles.
•Be sure the gap between the disc and disc table is 1/16” or less.
•If adjustment is necessary, loosen set screw in aluminum disc
through the opening at top-rear of disc guard. Position disc 1/16”
or less from edge of table. Secure disc with set screw.
ASSEMBLE BELT TABLE
Refer to Figure 3.
Slide belt table assembly into trunnion groove in pivot bracket.
Mount using socket head bolt and flat washer. Locate table in
desired position. Be sure that gap between belt table and belt is
1/16”or less. Tighten bolt securely.
ASSEMBLE BELT DUST CHUTE
Refer to Figure 3.
Mount belt dust chute to platen using two washer head screws.
INSTALLATION
Refer to Figures 4, 5 and 6.
WARNING: All electrical connections must be performed by a
qualified electrician.
POWER SOURCE
The motor is designed for operation on the voltage and frequency
specified. Normal loads will be handled safely on voltages not
more than 10% above or below the specified voltage.
Palmgren Operating Manual & Parts List 81091A
Figure 2 – Assemble Disc Table
End Shield
Flat Washers
Trunnion
Disc Table
Disc Guard
Dust Chute
Set Screw
Handle
Armature and Key
Aluminum Disc
with Abrasive
Disc
Belt Dust Chute
Belt Table
Screws
Figure 3 – Assemble Belt Table

4
INSTALLATION (CONTINUED)
Running the unit on voltages which are not within the range may
cause overheating and motor burnout.Heavy loads require that
voltage at motor terminals be no less than the voltage specified on
nameplate. Power supply to the motor is controlled by a single
pole locking rocker switch. Remove the key to prevent
unauthorized use.
GROUNDING INSTRUCTIONS
WARNING: Improper connection of equipment grounding con-
ductor can result in the risk of electrical shock. Equipment should
be grounded while in use to protect operator from electrical
shock.
•Check with a qualified electrician if grounding instructions are
not understood or if in doubt as to whether the tool is properly
grounded.
•This tool is equipped with an approved 3-conductor cord rated
at 300V and a 3-prong grounding type plug (See Figure 4) for
your protection against shock hazards.
•Grounding plug should be plugged directly into a properly
installed and grounded 3-prong grounding-type receptacle, as
shown (Figure 4).
•Do not remove or alter grounding prong in any manner. In the
event of a malfunction or breakdown, grounding provides a
path of least resistance for electrical shock.
WARNING: Do not permit fingers to touch the terminals of plug
when installing or removing from outlet.
•Plug must be plugged into matching outlet that is properly
installed and grounded in accordance with all local codes and
ordinances. Do not modify plug provided.If it will not fit in out-
let, have proper outlet installed by a qualified electrician.
•Inspect tool cords periodically, and if damaged, have repaired
by an authorized service facility.
•Green (or green and yellow) conductor in cord is the grounding
wire. If repair or replacement of the electric cord or plug is nec-
essary, do not connect the green (or green and yellow) wire to
a live terminal.
•Where a 2-prong wall receptacle is encountered, it must be
replaced with a properly grounded 3-prong receptacle installed
in accordance with National Electric Code and local codes and
ordinances.
WARNING: This work should be performed by a qualified
electrician.
•A temporary 3-prong to 2-prong grounding adapter (See
Figure 5) is available for connecting plugs to a two pole outlet
if it is properly grounded.
•Do not use a 3-prong to 2-prong grounding adapter unless
permitted by local and national codes and ordinances.
(A 3-prong to 2-prong grounding adapter is not permitted in
Canada.) Where permitted, the rigid green tab or terminal on
the side of the adapter must be securely connected to a per-
manent electrical ground such as a properly grounded water
pipe, a properly grounded outlet box or a properly grounded
wire system.
•Many cover plate screws, water pipes and outlet boxes are not
properly grounded.To ensure proper ground, grounding means
must be tested by a qualified electrician.
EXTENSION CORDS
•The use of any extension cord will cause some drop in voltage
and loss of power.
•Wires of the extension cord must be of sufficient size to carry
the current and maintain adequate voltage.
•Running the unit on voltages which are not within ±10% of the
specified voltage may cause overheating and motor burn-out.
•Use the table to determine the minimum wire size (A.W.G.)
extension cord.
•Use only 3-wire extension cords having 3-prong grounding
type plugs and 3-pole receptacles which accept the tool plug.
•If the extension cord is worn, cut or damaged in any way,
replace it immediately.
EXTENSION CORD LENGTH
Wire Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A.W.G.
Up to 25 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
NOTE: Using extension cords over 25 ft. long is not recommended.
ELECTRICAL CONNECTIONS
WARNING: All electrical connections must be performed by a
qualified electrician. Make sure tool is off and disconnected from
power source while motor is mounted, connected, reconnected or
anytime wiring is inspected.
•Motor and wires are installed as shown in wiring diagram (See
Figure 6). Motor is assembled with approved, 3-conductor cord
to be used at 120/240 volts.Motor is prewired at the factory for
120 volts.
•To use the tool with a 240V power supply, have a qualified elec-
trician rewire motor and attach a 240 volt, I5A three-prong plug
onto grinder line cord.
Palmgren Operating Manual & Parts List 81091A
Figure 5 – 2-Prong Receptacle with Adapter
Make sure this is
Connected to a
known Ground
2-Prong Receptacle
Grounding Lug
Adapter
3-Prong Plug Figure 6 – Wiring Diagram
3-Red 2-Gray
4-Yellow
1-Black
120V
240V
3-Red
1-Black
2-Gray
4-Yellow
Figure 4 – 3-Prong Receptacle
Grounding Prong
3-Prong Plug
Properly Grounded Outlet

5
OPERATION
Refer to Figure 7 and 8.
WARNING: Operation of any power tool can result in foreign
objects being thrown into eyes which can result in severe eye
damage. Always wear safety goggles complying with United States
ANSI Z87.1 (shown on package) before commencing power tool
operation.
CAUTION: Always observe the following safety precautions:
•Whenever adjusting or replacing any parts on the tool, turn
switch OFF and remove the plug from power source.
•Recheck table handles.They must be tightened securely.
•Make sure all guards are properly attached and securely
fastened.
•Make sure all moving parts are free and clear of any
interference.
•Make sure all fasteners are tight and have not vibrated loose.
•With power disconnected, test operation by hand to verify
clearance and adjust if necessary.
•Always wear eye protection or face shield.
•Make sure abrasive belt tracks properly. Correct tracking gives
optimum performance.
•After turning switch ON, always allow belt to come up to full
speed before sanding or grinding.
•Be sure motor runs clockwise on disc side. Abrasive belt must
travel down.
•Keep your hands clear of abrasive belt, disc and all moving
parts.
•For optimum performance, do not stall motor or reduce speed.
Do not force the work into the abrasive.
•Support workpiece with belt table when sanding with belt,
with disc table when sanding with disc.
•Never push a sharp corner of workpiece rapidly against belt or
disc. Abrasive backing may tear.
•Replace abrasives when they become loaded (glazed) or frayed.
•When grinding metal, move workpiece across abrasive to
prevent heat build-up.
•Never attempt wet sanding. If workpiece becomes too hot to
handle, cool it in water.
REPLACING ABRASIVE BELT
Refer to Figure 7.
•Sanding belt should be replaced when worn, torn, or glazed.
Remove belt dust chute by removing two washer head screws.
•Release belt tension by pushing tension lever towards idler
drum. Slide old belt off the idler and drive wheels.
NOTE: There may be an arrow on the inside of the belt.The arrow
should point down toward the belt table to ensure that the splice
in the belt will not come apart.
•Slide new belt over the drive and idler drums; center belt on
drums.
•Push tension lever towards drive drum to tension belt.
•Rotate belt by hand to check tracking. Belt should ride centered
on drive and idler drums. Adjust thumb nut as needed to cen-
ter belt on drums.When belt tracks properly, tighten hex nut. If
adjustment of thumb nut does not provide desirable tracking,
adjust the stud using a flat screwdriver.To adjust stud, loosen
hex nut and turn stud counterclockwise to move belt to the
right or clockwise to move belt to the left until belt rides cen-
tered on drive and idler drums.Tighten hex nut while holding
the stud in place.
•Mount belt dust chute using washer head screws.
ADJUST BELT ASSEMBLY POSITION
Refer to Figure 7.
Sanding belt assembly can be adjusted from horizontal to vertical
position.
•Loosen socket head bolt that is threaded into pivot bracket.
•Tilt belt assembly to desired position (from horizontal to verti-
cal). Secure belt assembly position by tightening socket head
bolt in pivot bracket.
ADJUST BELT TABLE
Refer to Figure 7.
•To adjust belt table angle, loosen socket head bolt.
•Tilt belt table to desired position. Adjust for 1/16” maximum
clearance between the belt and the table. Secure by tightening
socket head bolt.
HORIZONTAL BELT SANDING
Refer to Figure 7.
•The belt platen can be tilted from a vertical to a horizontal
position.
•Remove the belt table by removing the socket head bolt and
flat washer. Loosen the socket head bolt in the pivot bracket;
tilt the belt platen assembly to the horizontal position and
tighten the socket head bolt to secure position.
•Idler drum can be used as a contact drum to sand curved sur-
faces.
WORK STOP
Refer to Figure 8.
The work stop (Ref. No.39) can be used instead of the belt table.
•Remove socket head bolt and flat washer (Ref. Nos. 35 and 36)
holding belt table on pivot bracket. Remove belt table.
•Mount work stop to pivot bracket using the socket head bolt
and washer (Ref. Nos. 35 and 36).
ABRASIVE BELT FINISHING
Refer to Figure 7.
•Finishing flat surfaces: Hold workpiece firmly with both hands;
keep fingers away from abrasive belt.
Use work stop. Work stop is used to position and secure work
being sanded. Keep end butted against work stop and move
work evenly across abrasive belt. Use extra caution when finish-
ing very thin pieces.
Figure 7 – Adjusting Assembly
Hex Nut
Belt Dust Chute
Socket Head Bolt
Pivot Bracket
Thumb Nut
Tension Lever
Disc Table
Dust Chute
Release
Stud
Screws
Remove or
Adjust Belt
Table
Palmgren Operating Manual & Parts List 81091A

6
Palmgren Operating Manual & Parts List 81091A
OPERATION (CONTINUED)
Finishing long pieces: remove work stop. Apply only enough
pressure to allow abrasive belt to remove material.
•Finishing curved edges: Finish outside curves on flat portion of
abrasive belt. Finish inside curves on idler drum portion of
abrasive belt.
•Finishing end grain: It is more convenient to finish ends of long
workpieces with the abrasive belt in a vertical position.
Position table on belt side of sander. Lock into position with
socket head bolt and washer. Move work evenly across abrasive
belt. For accuracy, use miter gauge.Table may be tilted for
beveled work.
REPLACING ABRASIVE DISC
Refer to Figure 7.
•Remove disc table and dust chute. Remove old abrasive disc by
peeling it from the aluminum disc. Removing aluminum disc
from motor shaft is not necessary.
•Clean aluminum disc if necessary. Select the proper abrasive
disc and apply to aluminum disc.
•Replace dust chute and disc table.
ADJUSTING DISC TABLE ANGLE
Refer to Figure 7.
•Disc table is adjustable from 0 to 45º for beveled work.
•To adjust the disc table, loosen the two handles and pivot to
the desired angle.
•Use the scale on disc table trunnions to set table from 0 to 45º
from abrasive disc.
•When disc table is at desired angle, lock it into position by
securely tightening the handles.
ABRASIVE DISC FINISHING
•Abrasive disc sanding is well suited for finishing small flat
surfaces and convex edges.
•Move workpiece across down side (right) of abrasive disc.
•Abrasive disc moves fastest and removes more material at
outer edge.
•For accuracy, use miter gauge.
USING MITER GAUGE
Refer to Figure 8.
•The miter gauge is used on both belt and disc tables. Use the
miter gauge for securing the work and holding the proper
angle while sanding.
•Adjust angle by repositioning the miter gauge scale and
locking it into place with knob.
•Check accuracy of miter gauge scale.
•Use a combination square to adust miter gauge square to disc.
Indicator should be at zero. Loosen screw and reposition indica-
tor if necessary.
MAINTENANCE
WARNING: Make certain that the unit is disconnected from
power source before attempting to service or remove any
component.
CLEANING
•Keep machine and workshop clean. Do not allow sawdust to
accumulate on the tool.
•Keep the drums clean. Dirt on drums will cause poor tracking
and belt slippage.
•Operate tool with dust collector to keep dust from
accumulating.
WARNING: After sanding wood or non-metallic material, always
clean dust collector and guards of sawdust before grinding metal.
Sparks could ignite debris and cause a fire.
•Be certain motor is kept clean and is frequently vacuumed free
of dust.
•Use soap and water to clean painted parts, rubber parts and
plastic guards.
LUBRICATION
•The shielded ball bearings in this tool are permanently
lubricated at the factory.They require no further lubrication.
•When operation seems stiff, a light coat of automobile-type
wax applied to the belt table and disc table will make it easier
to feed the work while finishing.
•Do not apply wax to the belt platen. Belt could pick up wax and
deposit it on wheels causing belt to slip.
KEEP TOOL IN REPAIR
•If power cord is worn, cut or damaged, have it replaced
immediately.
•Replace worn abrasives when needed.
•Replace any damaged or missing parts. Use parts list to order
parts.
•Any attempt to repair motor may create a hazard unless repair
is done by a qualified service technician.

7
SYMPTOM
Motor will not start
Motor will not start; fuses blown or
circuit breakers tripped
Motor fails to develop full power
(power output of motor decreases
rapidly with decrease in voltage at
motor terminals)
Motor overheats
Motor stalls
(resulting in blown fuses or
tripped circuit breakers)
Machine slows down while operating
Abrasive belt runs off top wheel
POSSIBLE CAUSE(S)
1. Blown line fuse or tripped circuit breaker
2. Low line voltage
3. Defective switch
4. Defective, blown capacitor
1. Overloading due to binding
2. Defective plug
3. Defective cord
4. Defective switch
5. Motor wired for different line voltage
6. Faulty internal wiring
1. Power line overloaded with lights,
appliances and other motors
2. Undersized wires or circuits too long
3. General overloading of power
company’s facilities
Motor overloaded
1. Short circuit in motor or loose
connections
2. Low voltage
3. Motor wired for different line voltage
4. Incorrect fuses or circuit breakers in
power line
5. Motor overloaded
Applying too much pressure to workpiece
Not tracking properly
CORRECTIVE ACTION
1. If fuse is blown, replace with fuse of
proper size.If breaker tripped, reset it
2. Check power supply for voltage and
correct as needed
3. Replace switch
4. Replace capacitor
1. Clean around wheels and shaft and/or
replace bearings
2. Replace plug
3. Replace cord
4. Replace switch
5. Rewire motors as per line voltage
(See Electrical Connections, page 4)
6. Have a qualified electrician service unit.
1. Reduce load on power line
2. Increase wire sizes, or reduce length
of wiring
3. Request a voltage check from power
company
Reduce load on motor.
1. Inspect connections in motor for loose or
shorted terminals or worn insulation on
lead wires
2. Correct the low line voltage conditions
3. Rewire motor as per line voltage
4. Install correct fuses or circuit breakers
(See Electrical Connections, page 4)
5. Reduce load on motor
Ease up on pressure
See operation section
“Tracking Abrasive Belt”
TROUBLESHOOTING
Palmgren Operating Manual & Parts List 81091A

8
Palmgren Operating Manual & Parts List 81091A
Figure 8 – Replacement Parts Illustration for Sander
12
17
17
17
18
18
16
10
70 8
8
9
11 6
34
33
32
33
33
33
44
30
31
31
31
31
28
25
69
4
29
29
29
29
5
23
57
27 26
3
3
15
20
2
2
2
2
22
5
4
53
58
2
28
56
43
40
40
37
41
38
42
49
45
21
51
50
35
55
62
64
64
39
65
36
36
36
67
68
63
66
60
61
59
19
42
41
24
1
246
48
13
14
7
7
47
52
54

9
Ref.
No. Description Part No. Qty.
1 Abrasive belt 20768.00 1
2 8-1.25 x 10mm Set screw * 10
3 Collar 08403.00 2
4 Rubber bushing 08402.00 2
5 6 x 1.0mm Fiber hex nut * 1
6 Idler drum shaft 24593.00 1
7 3AMI-12 Retaining ring 00519.00 2
8 Bearing 6201ZZ 00520.00 2
9 Idler drum 24450.00 1
10 Thumb nut 08413.00 1
11 Stud 08412.00 1
12 Idler drum bracket 24446.00 1
13 Shoulder bolt 24447.00 1
14 Spring 08397.02 1
15 Tension lever 24448.00 1
16 Handle 24449.00 1
17 8-1.25 x 20mm Socket head bolt * 6
18 8mm Lock washer * 5
19 Stop rod 08394.00 1
20 Bumper 08395.00 1
21 Platen stop bracket 08393.00 1
22 Pivot bracket 24592.00 1
23 6 x 12mm Spring pin 25590.00 1
24 Platen 24445.00 1
25 Drive drum 24444.00 1
26 4 x 10mm Spring pin 08384.00 2
27 Belt table trunnion 24441.00 1
28 6-1.0 x 12mm Pan head screw * 6
29 6mm Lock washer * 21
30 Pivot stop bracket 08390.00 1
31 5-0.8 x 10mm Pan head screw * 8
32 Pointer 16643.00 1
33 5-0.8 x 8mm Pan head screw * 8
34 Belt dust chute 08380.01 1
35 10-1.5 x 25mm Socket head bolt * 1
36 10mm Flat washer 20132.00 3
Ref.
No. Description Part No. Qty.
37 Belt table 24440.00 1
38 Belt table assembly 24442.00 1
(Ref. Nos. 26,27 & 37)
39 Work stop 08381.00 1
40 6-1.0 25mm Pan head screw * 8
41 End shield 24439.09 2
42 Bearing 6205ZZ 02443.00 2
43 Armature 24438.00 1
44 Stator with housing 24435.09 1
45 Grommet 16916.00 2
46 Strain relief plate 08172.00 1
47 Switch with key 00423.00 1
48 Switch plate 08173.00 1
49 Base 16638.00 1
50 6-1.0mm Hex nut * 4
51 Capacitor 24436.00 1
52 Base cover 16919.00 1
53 Capacitor clamp 24437.00 1
54 #10 Serrated washer * 1
55 Strain relief 01601.00 1
56 Motor fan 24443.00 1
57 5 x 5 x 25mm Key 00975.00 1
58 Line cord 00090.00 1
59 Disc guard 08371.01 1
60 6mm Flat washer * 3
61 Disc dust chute 08372.00 1
62 Aluminum disc 08373.00 1
63 Abrasive disc 16731.00 1
64 Handle 08378.00 2
65 Right trunnion 08376.00 1
66 Left trunnion 08375.00 1
67 Disc table 08374.00 1
68 6-1.0 x 15mm Flat head screw * 4
69 Miter gauge assembly 08411.00 1
70 6-1.0mm Fiber hex nut 05153.00
Δ Operator’s Manual 25899.09 1
Palmgren Operating Manual & Parts List 81091A
REPLACEMENT PARTS LIST FOR SANDER
ΔNot Shown.
* Standard hardware item available locally.

Palmgren Operating Manual & Parts List 81091A
10
NOTES

Palmgren Operating Manual & Parts List 81091A
11
NOTES

Palmgren Operating Manual & Parts List 81091A
TWO YEAR LIMITED WARRANTY
Palmgren warrants to the original purchaser that all products covered under this warranty are free from defects in material and
workmanship for a period of two years from the date of the original purchase.
We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after
examination, proves to be defective in workmanship or material during the warranty period.
This warranty does not apply to repair or replacement required due to misuse, abuse, normal wear and tear, or repairs attempted or made
by other than our Service Department or an Authorized Service Representative. Proper use and care instructions are provided in the
\operator’s manual. Failure to follow these instructions will void the warranty.
This warranty gives you specific legal rights and you may also have other legal rights which may vary from state to state.
Responsibility of Original Purchaser (Initial User):
•To process warranty claim on this product, DO NOT return it to the retailer. The product must be evaluated by Palmgren.
Call [phone] for instructions.
•Retain original cash register sales receipt or invoice as proof of purchase for warranty work.
•Use reasonable care in the operation and maintenance of the product as described in the operator’s manual.
•Deliver or ship the product(s) to Palmgren. Freight costs, if any must be paid by the purchaser.
This Warranty Does Not Cover:
•Merchandise sold as reconditioned, used as rental equipment, and floor or display models.
•Repair and transportation costs of merchandise determined not to be defective.
•Expendable parts or accessories supplied with the product which are expected to become inoperative or unusable after a reasonable
period of use. See the operator’s manual for a list of accessories and expendable parts.