Palms 840 User manual

Palmse Mehaanikakoda, Võsupere küla, Vihula vald, Lääne-Virumaa 45202, Estonia.
tel. [phone] fax [phone] e-mail: [e-mail] http://www.palms.eu
USER MANUAL
FOREST CRANE PALMS 840

V 1.03 EN 2012 Palmse Mehaanikakoda LLC
TABLE OF CONTENTS
1. GENERAL.................................................................................................................1
2. SAFETY....................................................................................................................2
3. TECHNICAL DATA ..................................................................................................5
4. ASSEMBLY AND MOUNTING.................................................................................8
5. HYDRAULIC SYSTEM ...........................................................................................12
6. OPERATING INSTRUCTIONS...............................................................................22
7. DETACHING FOREST CRANE..............................................................................24
8. STORAGE INSTRUCTIONS...................................................................................24
9. MAINTENANCE......................................................................................................25
10. TROUBLESHOOTING............................................................................................29
11. SPARE PARTS.......................................................................................................30
12. WARRANTY...........................................................................................................37

FOREST CRANE PALMS 840
V 1.03 EN 2012 Palmse Mehaanikakoda LLC 1
1. GENERAL
This manual gives you a detailed overview about forest crane Palms 840. Read the
manual carefully before you start using this machine. The manual contains essential
directions for efficient and safe use of this equipment. These instructions should always
be followed. This forest crane is constructed for loading works in forestry and agriculture.
It can be mounted on Palms forest trailers by unified connection. This forest crane has
three point linkage system, by which it can be connected directly to agricultural tractors.
This machine meets all technical standards and safety regulations of EU Machinery
Directive and its amendments. Palms forest crane has CE marking.
Operator of forest crane is obliged to be aware of and strictly follow all safety precautions
and instructions described in this manual.
In addition to this, instructions of local occupational safety authorities, as well national
laws and regulations, must be followed.
Even if you are experienced user of this equipment, do not use it unless you have read
the user manual.
Using the machine for other tasks than those for which it is intended or exceeding its
performance is not allowed.
The manufacturer/dealer is not responsible for damage caused by misuse of the forest
crane.
Pay attention to regular maintenance. In case there will occur problems with forest crane,
which are not covered in this manual, contact authorized dealer or manufacturer.
Palmse Mehaanikakoda LLC reserves the right to make changes to user manuals and to
revise the data without prior notice.
Fi
g
ur
e
1

FOREST CRANE PALMS 840
V 1.03 EN 2012 Palmse Mehaanikakoda LLC 2
2. SAFETY
2.1 General
Read the manual carefully before you start operating this forest crane. Use forest crane
only for right purposes. The operator must have a proper valid licence to work with the
tractor and the forest crane. The operator has to have sufficient training prior using of this
machine.
Notice, avoid and prevent all potentially hazardous situations!
IT IS STRONGLY FORBIDDEN:
to use forest crane in state of intoxication by alcohol, drugs or other
psychoactive substances.
to exceed maximum loading values.
to leave the load in UP position without supervision.
to use forest crane for lifting people.
to rebuild forest crane.
to use repairing materials without the producer’s permission.
to localize a leakage from hydraulic hoses or connections by hand.
BEFORE YOU START OPERATING FOREST CRANE, MAKE SURE THAT:
crane is in working condition.
you have full visibility over all the working area.
crane is placed firmly on even ground.
the tractor parking brake is engaged.
IT IS RESPONSIBILITY OF THE USER:
to ensure that attachments and connections to the vehicle are designed
and adapted in such a way that they meet the crane’s needs according
to technical data.
to install a loose crane on equipment other than a Palms trailer such
way that the vehicle has the necessary capacity to cope with the lifting
and slewing torques that the crane is designed to handle.

FOREST CRANE PALMS 840
V 1.03 EN 2012 Palmse Mehaanikakoda LLC 3
2.2 Safety distances
General safety distance for working with forest crane is 20 metres!
Follow special safety distance when working close to live electrical conductors:
Rated voltage, kV
Safety area, m
Up to 0,5
2
Up to 20
10
35 –110
25
220 –330
40
Table 1. Safety area
All electrical conductors must be clearly visible while operating the forest crane.

FOREST CRANE PALMS 840
V 1.03 EN 2012 Palmse Mehaanikakoda LLC 4
2.3 Hydraulic system
Hydraulic system must be serviced by qualified and experienced
hydraulics mechanic only.
Continually inspect the condition of hydraulic system. Repair all safety
en-dangering defects immediately.
Before hydraulics maintenance work make sure that the system is not
under pressure.
When replacing hydraulic components and hoses, use original spare
parts or parts recommended by the manufacturer.
When perfoming maintenance work, use safety goggles and gloves.
Prevent oil dripping to the ground in order to avoid environmental
pollution.
When working in ecologically sensitive areas, use bio-oil.
2.4 Operation
Ensure, that forest crane is in good working condition.
Operating with damaged or defective machine is prohibited.
Ensure, that you have best possible sight and control over the working
area.
Prevent unauthorized persons access to the working area.
Support legs must be used while working with forest crane.
Be sure not to endanger anyone while lowering support legs.
Pull support legs up before moving the tractor.
Use tractor parking brake during working with forest crane.
Do not use an equipment, which is not recommended by the
manufacturer.
Never lift heavier load, than allowed by the manufacturer.
When leaving the machine, always secure it from unauthorized access
and unintended operation.
Manufacturer is not responsible for any damage or loss, that is caused
by misuse or incorrect, careless,unauthorized and inappropriate use of
the machine.
Follow the traffic regulations while driving on public roads!

FOREST CRANE PALMS 840
V 1.03 EN 2012 Palmse Mehaanikakoda LLC 5
3. TECHNICAL DATA
3.1 Dimensions of the forest crane
Figure 1. Palms 840 dimensions (mm)
Figure 2. Grapple 0,215 Pro dimensions (mm)

FOREST CRANE PALMS 840
V 1.03 EN 2012 Palmse Mehaanikakoda LLC 6
3.2 Lifting reach
Figure 3. Lifting reach of Palms 840 forest crane

FOREST CRANE PALMS 840
V 1.03 EN 2012 Palmse Mehaanikakoda LLC 7
3.3 Technical data
Max reach
8,4 m
Lifting torque, kNm, bruto
62 kNm
Lifting power on 4m without graple and rotator
1050 kg
Lifting power on full reach without graple and rotator
470 kg
Grapple
0,22 m3
Rotator
GR 46
Grapple and rotator weight
135 kg
Slewing torque
15 kNm
Slewing cylinders
4
Boom rotation
370°
Hydraulic valve, standard
NH 6/8 XY
Working pressure
180 bar
Hydr pump capacity, l/min
70 l/min
Total weight
1600 kg
Table 2. Technical data table of Palms 840
3 m 4 m 5 m 8,4 m
PALMS 840 1460kg 1100kg 880kg 470kg
Figure 4. Palms 840 lifting power on different distances
Manufacturer reserves the right to change specifications without prior notice.

FOREST CRANE PALMS 840
V 1.03 EN 2012 Palmse Mehaanikakoda LLC 8
4. ASSEMBLY AND MOUNTING
Read these instructions before starting any assembly or mounting of crane. Improper
mounting, carried out in a manner other than specified in this manual, may cause
dangerous situations to user and surrounding objects. Improper mounting, useage and
installations will void the manufacturer warranty.
4.1 Mounting forest crane to Palms trailer
Mounting of forest crane should be performed at the dealer service center or by person
authorized by the manufacturer or dealer. Mounting/detaching the crane can also be
made by end user, if professional equipment is used, all safety regulations are followed
and at least one qualified mechanic is present during all the mounting/detaching process.
Strength class for mounting bolts of slewing device-support legs (pos. 1, fig.5) and
support legs-trailer (pos. 2, fig. 5) has to be 12.9 (DIN912). Use self-locking nuts M24.
The tightening torque for the mounting bolts of the crane (pos. 1, fig. 5) and supporting
legs (pos. 2, fig. 5) is 1220 Nm.
Retighten bolts after the test run and after first 8 hours of use! Check after
40 working hours, tighten if needed. Visual check is required prior every
working session.
Figure 5. Connection junctions on Palms 840 support legs
2
1