Panacom PAN810WK User manual

USER MANUAL
Caution: Please read the manual carefully before use.
CCTV CAMERA
MODEL No.: PAN810WK
PANACOM 2.4GHz WIRELESS
7’’ VIDEO DOORPHONE KIT
It is very important to install and operate this product
according to the following instruction.
Failure to do so may render your guarantee void.

Part Description
Indoor monitor (PAN810WM)
Outdoor station (PAN810WD)
Packing list:
1 x 7” Indoor Monitor (PAN810WM)
1 x Wireless Door Station (PAN810WD)
1 x Indoor Monitor Power Supply
1 x Indoor Monitor Wall Bracket
1 x USB charging cable for door station
1 x Screws & Plugs
1 x User Manual
*NOTE: Door Station & Monitor is paired/synced as factory default.
1. Power On/Off
2. TF card slot
3. DC power socket
4. Talking volume adjustment
5. Color adjustment
6. Brightness adjustment
7. Touch buttons
Camera
1. Power Input 13.5V
2. Power Input G
3. Manual lock
4. 12V Out: 12V
5. Electronic Lock
6. Magnetic Lock
Night View Lamp
Speaker
Unlock Interval
Alarm Switch Code Button
Call Button
Indicator Light
MIC USB Charge Port
2 3

Please Note:
• Door station requires external power supply for below features to operate:
- Call button indicator is on during standby mode and will flash when pressed.
- Door release function (12Vdc 400mA max)
- Monitoring of door station from internal monitor
• When charging, indicator will be red. Once completed the indicator light will turn off
• For the door unlock time, when jumper is shorting the pins, unlock time is 5s.
When not shorting the pins, unlock time is 1s.
OPTIONAL ITEM:
Wireless CCTV Camera (PAN810WC)
Operating Instructions:
Power On/Off: Press & hold for 3 seconds to power ON or OFF
SD Card slot: Supports up to 32GB
DC Power Input: Plug in supplied DC adapter to power & recharge built-in lithium battery
Volume Control to adjust communication volume. To adjust ring volume, enter ring settings.
Colour Adjustment: In monitor mode, adjust colour of image
Brightness Adjustment: In monitor mode, adjust brightness of image
Antenna
Power Adapter
Camera Lens
4 5

Touch the light buttons that match display icons for operation.
Button 1 is the HOME key. On standby, the light is red with slow flash.
Press to turn ON/OFF display screen.
Button 2 will flash if you have missed a call from the door camera.
Press to review the recorded images if SD card is fitted.
Button 3 will flash if the indoor monitor battery is low. Connect DC power to charge.
Indoor Battery Display
Wireless Signal
Strength
Monitoring Selection
Recording/Snapshot
File
Setup
Date/Time Display
Main Interface
Indoor Battery Display
Time Display
Gate Unit No. Display
Manual Snapshot
Manual Recording
Answer/Hang Up
Unlock
Return
Call Interface
Monitoring Interface
Select camera 1-4 to monitor individual cameras or select the QUAD screen mode
to view all 4 in one screen.
Note: Monitoring function can be used when cameras are powered by DC power supply.
It will not function when powered by battery only.
6 7

Return
Memory display
/ Formatting
Automatic Snapshot
/ recordingSetup
Electronic Instructions /
Code Matching / Reset
Ring Setup
Time Setup
Setup Interface
Press to enter the electronic instructions
Hold for 3s to enter Code Matching & System Restore Mode
Code Matching:
Hold for 3s to enter Code Matching & System Restore Mode
Press to enter Code Matching Mode
For Door Camera, Press to choose the corresponding outdoor unit.
Press to start code matching thereafter press code matching button on the outdoor
unit. Once matched, will be displayed.
For wireless CCTV camera, Press to choose the corresponding outdoor unit.
Press to start code matching thereafter apply power to the wireless camera.
Once matched, will be displayed.
System Restore
Press Match Button to restore all functions to factory default.
Press to confirm reset to default.
press to return to the last page
8 9

Automatic Recording Settings
In this mode, when outdoor unit is called, 3 pictures are taken automatically
In this mode, when outdoor unit is called, a 15sec video will be recorded
In this mode, when outdoor unit is called, no photo or video will be recorded.
Note: for recording function, SD card must be fitted.
SD Card Formatting
Select SD card formatting, press to start
Confirm to delete or not?, press to start SD card formatting
or else, press to return to the last page
SD card capacity is shown after formatting finish.
Specifications:
Display 7’’ TFT- LCD, 800*480 resolution
Door Station 480TVL, 90º viewing angle, IP45
Frequency 2.4GHz Digital Wireless
Video
Motion-JPEC and JPEG encoder and decoder for image
snapshoot
VGA video at 25fps with 2Mbps/3Mbps/4Mbps RF data rate
Support 4 PiP (picture-in-picture) display
Audio Full duplex
Communication distance Max 100 meters in open area line of sight
Power supply
Indoor monitor: 5V/2000mA
Outdoor station: 12V/1500mA
CCTV camera: 5V/1A
Working current
Indoor monitor: 750mA
Outdoor station: 250mA
CCTV camera: 250mA
Standby current
Indoor monitor: 200mA
Outdoor station: 0.13mA
CCTV camera: 250mA
Internal batteries Indoor monitor: 3.7V 3300mAh
Outdoor station: 3.7V 2600mAH
Memory card Max 32G (not included)
Working temperature -20°C - 50°C
Dimension(W/H/D)
Indoor monitor: 191 x 120 x 18mm
Outdoor station: 78 x 145 x 26mm
CCTV camera: 65 x 54 x 173mm
Ring tones 16 ring tones for option
10 11

WARRANTY & LIABILITY
1 PSA Products Pty Ltd (ABN: 99 076 468 703) of 17 Millicent Street, Burwood 3125 Victoria,
Australia warrants this product for a period of one year from the date of purchase,
as reflected on the Authorised Resellers or Distributors invoice/ receipt provided to you.
PSA Products Pty Ltd will repair or replace the product (at the option of PSA Products)
due to any manufacturing defect, at the cost of PSA Products Pty Ltd (excluding any
labour costs relating to removal or re-installation of product, and transport costs).
2 This warranty shall not apply to the product if it has been damaged, modified, abused
or altered after the date of purchase, or if it fails to operate due to improper maintenance.
3 To the extent permitted by law, the liability of PSA Products Pty Ltd arising from the sale
or under the terms of this limited warranty shall not in any case exceed the cost of
replacement and subject to this clause. In no case shall PSA Products Pty Ltd be liable
for consequential loss or damages resulting from the failure of the product or breach of this,
or: Any other warranty, express or implied, loss or damage caused by failure to abide by
the instructions supplied in the leaflets.
4 To the extent permitted by law, PSA Products Pty Ltd., makes no warranty, expressed or
implied, written or oral, including that of merchantability or fitness for any particular purpose,
with respect to the consumer replaceable battery if any. A product with non-serviceable
built-in battery is covered under warranty of the product as per point 1.
5 This warranty is provided in addition to other rights and remedies you have under law:
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure. What constitutes a major failure is set out in the Australian
Consumer Law.
6 To make a claim under warranty, take the product (with a proof of purchase) to the store
where you purchased the product or contact PSA Products Pty Ltd. Phone [phone].
or Email: enquiry@ psaproducts.com.au with details, proof of purchase or expense claim
in writing.
12
PSA Products
17 Millicent Street, Burwood, VIC 3125 Australia
Tel: 1300 PSA PRODUCTS (1300 772 776)
Fax: [phone]
[e-mail] psaproducts.com.au