Panasonic FX-301-HS User manual

For further details on the fiber sensor amplifier, please refer to 'Panasonic Electric
Works SUNX website (http://panasonic-electric-works.net/sunx)' or contact our office.
٨
٨
Never use this product as a sensing device for personnel protection.
In case of using sensing devices for personnel protection, use prod-
ucts which meet laws and standards, such as OSHA, ANSI or IEC
etc., for personnel protection applicable in each region or country.
WARNING
SPECIFICATIONS
1
12 to 24V DCr10% Ripple P-P 10% or lessSupply voltage
Item FX-301P-HSFX-301-HS
PNP outputType
Model No.
NPN output
Power consumption
Normal operation: 960mW or less
(current consumption 40mA or less at 24V supply voltage)
ECO mode: 600mW or less
(current consumption 25mA or less at 24V supply voltage)
Output
<NPN output type>
NPN open-collector transistor
࡮
Maximum sink current: 100mA (Note 1)
࡮Applied voltage: 30V DC or less
(between output and 0V)
࡮Residual voltage: 1.5V or less
[at 100mA (Note 1) sink current]
<PNP output type>
PNP open-collector transistor
࡮
Maximum source current: 100mA (Note 1)
࡮Applied voltage: 30V DC or less
(between output and +V)
࡮Residual voltage: 1.5V or less
[at 100mA (Note 1) source current]
2-level teaching / Limit teaching / Full-auto teaching /
Manual adjustment
Sensitivity setting
H-SP: 35Ǵs or less, FAST: 150Ǵs or less, S-D: 250Ǵsorless,
STD: 250Ǵs or less, LONG: 2ms or less selectable with jog switch
Response time
4 digit red LED displayDigital display
Light-ON or Dark-ON, selectable with jog switchOutput operation
Incorporated
Short-circuit protection
Ambient temperature
-10to+55(If 4 to 7 units are connected in cascade: -10 to +50,
if 8 to 16 units are connected in cascade: -10 to +45)
(No dew condensation or icing allowed), Storage: -20 to +70
Timer function
Incorporated with variable ON-delay / OFF-delay / ONE-SHOT timer,
switchable either effective or ineffective (Timer: approx. 0.5 to 9999ms)
Incorporated
Fine sensitivity
adjustment function
Red LED (modulated)Emitting element
Enclosure: Heat-resistant ABS, Transparent cover: Polycarbonate
Press switches: Acrylic, Jog switch: Heat-resistant ABS
Material
20g approx.Weight
35 to 85% RH, Storage: 35 to 85% RHAmbient humidity
Notes: 1)
2)
50mA, if five, or more, amplifiers are connected in cascade.
The cable for amplifier connection is not supplied as an accessory. Make sure to use the
optional quick-connection cables given below.
Main cable (3-core): CN-73-C1 (cable length 1m), CN-73-C2 (cable length 2m)
CN-73-C5 (cable length 5m)
Sub cable (1-core): CN-71-C1 (cable length 1m), CN-71-C2 (cable length 2m)
CN-71-C5 (cable length 5m)
CONNECTION
3
Make sure that the power supply is off while connecting or disconnecting the quick-
connection cable.
Ԙ
ԙ
Holding the connector of the quick-connection cable, align
its projection with the groove at the top portion of the
amplifier connector.
Insert the connector till a click is felt.
ԘPressing the projection at the top of the quick-connection
cable, pull out the connector. Projection
Groove
Projection
Quick-connection cable
Connection method
Disconnection method
Take care that if the connector is pulled out without pressing the
projection, the projection may break. Do not use a quick-
connection cable whose projection has broken. Further, do not pull
by holding the cable, as this can cause a cable-break.
Note:
CAUTIONS
4
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
This product has been developed / produced for industrial use only.
This product does not incorporate the optical communication function (copy
function and interference prevention function).
When the emission halt of the emitting power switching function is set from 'OFF' to
'ON', the output may be unstable. Do not use the output control for 0.5 sec. after
starting emission.
Make sure that the power supply is off while wiring.
Verify that the supply voltage variation is within the rating.
Take care that if a voltage exceeding the rated range is applied, or if an AC power
supply is directly connected, the sensor may get burnt or damaged.
In case noise generating equipment (switching regulator, inverter motor, etc.) is
used in the vicinity of this product, connect the frame ground (F.G.) terminal of the
equipment to an actual ground.
If power is supplied from a commercial switching regulator, ensure that the frame
ground (F.G.) terminal of the power supply is connected to an actual ground.
Do not use during the initial transient time (0.5 sec.) after the power supply is
switched on.
Take care that short-circuit of the load or wrong wiring may burn or damage the
sensor.
Do not run the wires together with high-voltage lines or power lines or put them in
the same raceway. This can cause malfunction due to induction.
Make sure to use the optional quick-connection cable for connection of the amplifier.
Extension up to total 100m (if 5 to 8 units are connected in cascade: 50m, if 9 to 16
units are connected in cascade: 20m) is possible with 0.3mm2, or more, cable.
However, in order to reduce noise, make the wiring as short as possible.
Take care that cable extension increases the residual voltage.
This sensor is suitable for indoor use only.
Avoid dust, dirt, and steam.
Take care that the product does not come in contact with water, oil, grease,
organic solvents, such as, thinner, etc., strong acid or alkaline.
This sensor cannot be used in an environment containing inflammable or explosive
gases.
Never disassemble or modify the sensor.
MOUNTING
2
Ԙ
ԙ
Fit the rear part of the mounting section of the amplifier
on a 35mm width DIN rail.
Press down the rear part of the mounting section of the
unit on the 35mm width DIN rail and fit the front part of
the mounting section to the DIN rail.
How to mount the amplifier
Ԙ
35mm width DIN rail
ԙ
Ԙ
ԙ
Push the amplifier forward.
Lift up the front part of the amplifier to remove it.
Ԙ
ԙ
Take care that if the front part is lifted without pushing the amplifier forward, the hook on the
rear portion of the mounting section is likely to break.
Note:
How to remove the amplifier
How to connect the fiber cables
Ԙ
ԙ
Ԛ
Snap the fiber lock lever down.
Insert the fiber cables slowly into the inlets until they
stop. (Note 1)
Return the fiber lock lever to the original position, till it
stops.
Notes: 1)
2)
In case the fiber cables are not inserted to a position where
they stop, the sensing range reduces. In case of a flexible
fiber, take care that it may bend inside the amplifier, during
insertion.
With the coaxial reflective type fiber, such as, FD-G4 or FD-FM2, insert the single-core fiber
cable into the beam-emitting inlet and the multi-core fiber cable into the beam-receiving
inlet. If they are inserted in reverse, the sensing accuracy will deteriorate.
Ԙ
ԙ
Ԛ
Fiber
lock lever
Fiber
Be sure to fit the attachment to the fibers first before inserting the fibers to the
amplifier. For details, refer to the instruction manual enclosed with the fibers.
ME-FX301HS No.0017-07V
CASCADING
5
٨
٨
٨
٨
٨
٨
٨
Make sure that the power supply is off while adding or removing the amplifiers.
Make sure to check the allowable ambient temperature, as it depends on the num-
ber of amplifiers connected in cascade.
In case two, or more, amplifiers are connected in cascade, make sure to mount
them on a DIN rail.
When the amplifiers move on the DIN rail depending on the attaching condition or
the amplifiers are mounted close to each other in cascade, fit them between the
optional end plates (MS-DIN-E) mounted at the two ends.
Up to maximum 15 amplifiers can be added (total 16 amplifiers connected in cascade.)
When connecting more than two amplifiers in cascade, use the sub cable (CN-71-Cغ)
as the quick-connection cable for the second amplifier onwards.
When this sensor is used by cascading along with the other digital fiber amplifier,
since the optical communication function (copy function and interference preven-
tion function) is not incorporated, mount identical models together.
For mounting and removing the amplifier, refer to ' MOUNTING'.
2
Ԙ
ԙ
Ԛ
ԛ
Mount the amplifiers, one by one,
on the 35mm width DIN rail.
Slide the amplifiers next to each
other, and connect the quick-con-
nection cables.
Mount the optional end plates
(MS-DIN-E)
at both the ends to hold
the amplifiers between their flat sides.
Tighten the screws to fix the end
plates.
Cascading method
Ԙ
ԙ
Ԛ
Loosen the screws of the end plates.
Remove the end plates.
Slide the amplifiers and remove
them one by one.
Dismantling
Main cable (CN-73-Cغ)
(optional)
End plates (MS-DIN-E)
(optional)
End plates (MS-DIN-E)
(optional)
Sub cable (CN-71-Cغ)
(optional)
Slide
Slide
Thank you very much for purchasing Panasonic products. Please read this Instruction
Manual carefully and thoroughly for the correct and optimum use of this product.
Kindly keep this manual in a convenient place for quick reference.
INSTRUCTION MANUAL
Digital Fiber Sensor Amplifier FX-301-HS

I/O CIRCUIT DIAGRAMS
6
Notes: 1)
2)
The quick-connection sub cable does not have +V (brown) and 0V (blue).
The power is supplied from the connector of the main cable.
50mA max., if five, or more, amplifiers are connected in cascade.
Symbols...D1,D2: Reverse supply polarity protection diode
ZD1,ZD2: Surge absorption zener diode
Tr1: NPN output transistor
Tr2: PNP output transistor
٨NPN output type
1
+V
3
Output
2
0V
Terminal arrange-
ment diagram
D1
1
2
3
ZD1
Tr1
100mA max. (Note 2)
Load
(Brown) +V (Note 1)
(Black) Output
+12 to 24V DC
r10%
-
(Blue) 0V (Note 1)
Users' circuitInternal circuit
Sensor circuit
Terminal No.
Color code of quick-connection cable
٨PNP output type
Terminal arrange-
ment diagram
1
+V
3
Output
2
0V
Terminal No.
Color code of quick-connection cable
D2
ZD2
1
2
3
Tr2
Load
+12 to 24V DC
r10%
-
100mA max. (Note 2)
(Brown) +V (Note 1)
(Black) Output
(Blue) 0V (Note 1)
Users' circuitInternal circuit
Sensor circuit
PART DESCRIPTION
7
MODE key
Jog switch
Digital display (Red)
MODE indicator /
PRO (Yellow)
MODE indicator / L/D ON (Yellow)
Operation indicator (Orange)
MODE indicator / RUN (Green)
MODE indicator / ADJ (Yellow)
MODE indicator / TEACH (Yellow)
MODE indicator / TIMER (Yellow)
Stability indicator
(Green)
OPERATION PROCEDURE
8
٨When the power supply is switched on, MODE indicator /
RUN (green) lights up and the digital display shows the
incident light intensity.
MODE key
Press Press 6WTP
'+' side '-' side
Jog switch
*1:
*2:
*3:
*4:
When Jog switch is pressed, the setting is confirmed.
When MODE key is pressed for 2 sec., or more, the sensor returns to the 'RUN' mode.
Cancellation is possible by pressing MODE key during setting.
When Jog switch is turned in the 'RUN' mode, the current threshold value is displayed.
And then, the current incident light intensity display appears again automatically.
٨NAVI mode
This indicates normal sensing operation.
RunRUN
Press
Press
10
Refer to ' THRESHOLD VALUE FINE
ADJUSTMENT MODE'.
Allows fine adjustment of the threshold value.
AdjustADJ
Press
Press
Press
Press
Refer to ' OUTPUT OPERATION
SETTING MODE'.
11
Sets output operation either Light-ON, or Dark-ON.
L-ON/D-ONL/D
Refer to ' TIMER OPERATION
SETTING MODE'.
12
Configures operation of the timer.
TimerTIMER
Refer to ' PRO MODE'.
13
Allows various detailed settings to be configured,
such as save/load and other settings.
ProPRO
Press
٨
To PRO mode
Refer to ' TEACHING MODE'.
9
Sets the threshold value by, '2-level teaching', 'limit
teaching' or 'full-auto teaching'.
TeachingTEACH
٨PRO mode
TEACHING MODE
9
In case of 2-level teaching
٨
This is the method of setting the threshold value by teaching two levels, corre-
sponding to the object present and object absent conditions. Normally, setting is
done by this method.
Press
Press
Press
ԝ
Ԝ
ԛ
Ԛ
ԙ
Ԙ
࡮
The incident light intensity appears in the digital display and the setting is complete.
࡮The threshold value is displayed.
If the teaching is accepted, the read incident light intensity blinks in the digi-
tal display and the threshold value is set at the mid-value between the inci-
dent light intensities in the object present and the object absent conditions.
After this, the judgment on the stability of sensing is displayed.
In case stable sensing is possible: '㵘㵘㵘㵘' is displayed.
In case stable sensing is not possible: '㵘㵘㵘㵘' is displayed.
࡮
࡮
࡮
The MODE indicator / TEACH (yellow) blinks.
Press Jog switch in the object absent condition.
࡮
࡮
Press Jog switch in the object present condition.
If the teaching is accepted, the read incident light intensity
blinks in the digital display.
Step
࡮
࡮
Set the fiber within the sensing range.
Press MODE key to light up MODE indicator /
TEACH (yellow).
Display Description
Note:
In case of limit teaching
٨
The approx. 15% amount of shift is the initial value. The amount of shift can be changed in the
PRO mode from approx. 0 to 80% (5% step). Refer to ' PRO MODE / PRO1 mode setting'
for the setting method.
13
This is the method of setting the threshold value by teaching only the object
absent condition (stable incident light condition). This is used for detection in the
presence of a background body or for detection of small objects.
Press
Press
Ԙ
࡮
࡮
Set the fiber within the sensing range.
Press MODE key to light up MODE indicator /
TEACH (yellow).
Step Display Description
Turn
࡮
The incident light intensity appears in the digital display and the setting is complete.
࡮The threshold value is displayed.
ԛ
Ԛ࡮
࡮
The MODE indicator / TEACH (yellow) blinks.
Turn Jog switch to the '+' side or the '-' side.
ԙ
࡮
࡮
Press Jog switch in the object absent condition.
If the teaching is accepted, the read incident light intensity
blinks in the display.
Ԟ
ԝ
Ԝ
࡮
After this, the judgment on whether the set shift amount is possible or not will be displayed.
When the shift is possible: ' ' is displayed.
When the is not possible: ' ' is displayed.
࡮
࡮
If Jog switch is turned to the '+' side, ' ' scrolls (twice) the
display from right to left, and the threshold level is shifted to a
value approx. 15% higher (lower sensitivity) than that set at ԙ.
(Note) This is used in case of reflective type fibers.
If Jog switch is turned to the '-' side, ' ' scrolls (twice) the
display from left to right, and the threshold level is shifted to a
value approx. 15% lower (higher sensitivity) than that set at ԙ.
(Note) This is used in case of thru-beam type fibers.
Turn to '+' side
Turn to '-' side
15%
15%
Sensitivity level
with object absent
Sensitivity level
Sensitivity level
0
100%
Turn to '+' side
Turn to '-' side
ON
OFF
OFF
ON
High
Low
Sensitivity
level
The functions in PRO3 mode and PRO4 mode are the same.Note:
Refer to ' PRO
MODE PRO1
mode setting'.
13
Refer to ' PRO
MODE PRO3
mode setting'.
13
Refer to ' PRO
MODE PRO2
mode setting'.
13
Refer to ' PRO
MODE PRO5
mode setting'.
13
Refer to ' PRO
MODE PRO4
mode setting'.
13
Turn
Response time change function ''
Timer setting function ''
Hysteresis function ''
࡮
࡮
࡮
Stability function ''
Shift function ''
Emitting power selection function ''
࡮
࡮
࡮
PRO1
PRO5
PRO4
Digital display setting function ''
Digital display inversion function ''
ECO mode setting function ''
࡮
࡮
࡮
PRO2
Turn
Turn
Turn
Turn
Data bank load setting function ''
Data bank save setting function ''
࡮
࡮
PRO3 (Note)
Data bank load setting function ''
Data bank save setting function ''
࡮
࡮
PRO4 (Note)
Setting reset function ''࡮
࡮
࡮
Code setting function ''
Adjust lock setting function
''
The 0-ADJ setting function in this product was removed from production starting May, 2005.

In case of full-auto teaching
٨Full-auto teaching is used when it is desired to set the threshold value without
stopping the assembly line, with the object in the moving condition.
If the teaching is accepted, the read incident light intensity blinks in the digi-
tal display and the threshold value is set at the mid-value between the inci-
dent light intensities in the object present and the object absent conditions.
After this, the judgment on the stability of sensing is displayed.
In case stable sensing is possible: '㵘㵘㵘㵘' is displayed.
In case stable sensing is not possible: '㵘㵘㵘㵘' is displayed.
࡮
࡮' ' is displayed on the digital display. Release the jog switch when the
object has passed.
ԛ
Ԛ
ԙ
Ԙ
࡮Press Jog switch continuously for 0.5 sec. or more with the
object moving on the assembly line. (The incident light intensi-
ty is displayed during sampling.)
Step
࡮
࡮
Set the fiber within the sensing range.
Press MODE key to light up MODE indicator /
TEACH (yellow).
Display Description
ԝ
Ԝ
࡮ The incident light intensity appears in the digital display and the setting is complete.
࡮The threshold value is displayed.
Press
Press
PRO MODE
13
For details of the settings and the setting procedure of the PRO mode, refer to 'Panasonic Elec-
tric Works SUNX website (http://panasonic-electric-works.net/sunx)' or contact our office.
٨PRO settings can be done when MODE indicator / PRO
(yellow) lights up.
THRESHOLD VALUE FINE ADJUSTMENT MODE
10
࡮When Jog switch is turned to the '-' side, the threshold value decreases (sensitivity
increases).
When Jog switch is pressed, the threshold value is confirmed.
Confirmed
Press Turn to '+' side.Turn to '+' side.
Confirmed
Press Turn to ' - ' side. Turn to ' - ' side.
٨
࡮
Fine adjustment of the threshold value can be done
when MODE indicator / ADJ (yellow) lights up.
When Jog switch is turned to the '+' side, the threshold
value increases (sensitivity decreases).
When Jog switch is pressed, the threshold value is confirmed.
OUTPUT OPERATION SETTING MODE
11
Confirmed
Press
Turn
٨
࡮
The output operation setting can be done when MODE
indicator / L/D (yellow) lights up.
The output operation is changed when Jog switch is
turned to the '+' side or the '-' side.
When Jog switch is pressed, the threshold value is confirmed.
TIMER OPERATION SETTING MODE
12
٨
٨
٨
The setting for whether the timer is used or not can be
done when MODE indicator / TIMER (yellow) lights up.
10ms OFF-delay (initial value) timer is automatically set
when the timer is set to be used.
Refer to ' PRO MODE / PRO1 mode setting' for the setting method of the OFF-
delay timer, ON-delay timer and ONE-SHOT timer intervals.
13
Press: Confirmed
Turn
Turn Turn
Turn
(Without timer)
ONE-SHOT
timer
OFF-delay
timer
ON-delay
timer
The timer interval set in the PRO mode is displayed.
The factory setting is without timer ' '.
Notes: 1)
2)
PRO1 mode setting
Turn
Turn
Turn
Response time: 150Ǵsorless High speed
Response time: 35Ǵs or less Ultra high speed
Reduced intensity (Note)
Response time: 250Ǵsorless
Response time: 250Ǵsorless
Standard
Response time: 2ms or less
Long-range
Note: The S-D mode is suitable for delicate sensing, such as when
the received lights is saturated due to too short a sensing dis-
tance or when detecting translucent objects, etc.
The amount of shift can be changed approx. 0 to
80% (5% step).
Press
Press
Press
Turn
Turn
Press
Turn
Emission halt
Press Turn
Press
Turn
Turn
Turn
Turn
Turn
Emitting power Hi
Emitting power Lo
Hysteresis: Standard
Hysteresis: Large
Hysteresis: Small
Margin width:r10%
Margin width:r15%
Margin width:r5%
OFF-delay timer
Without timer
ONE-SHOT timer
ON-delay timer
Amount of shift: 15% approx.
The range of available timer delays is
0.5ms, 1 to 9999ms (1ms increments).
Turn
Note: Only in the response time࡮H-SP mode, ON condition, the emit-
ting power is 2 level.
Press Press
Response
time change
function
Emitting
power selec-
tion function
Timer set-
ting function
Hysteresis
function
Stability
function
Shift
function
Note: Set the threshold value at least a bit higher than the minimum threshold value. (The minimum
threshold value is where the value cannot be lowered any further even if the jog switch is
turned to '-' side.)

PRO2 mode setting
Press Press
Press
Press
Turn
Turn
Turn
Turn
Turn
Turn
Bottom hold display
Incident light intensity display
Percentage display
Peak hold display
Turn OFF
Turn ON
ECO OFF
ECO ON
Digital dis-
play setting
function
Digital dis-
play inver-
sion function
ECO mode
setting
function
1CH
2CH
3CH
1CH
2CH
3CH
Press
Press
Press
Turn
Press
Press
Press
Press
Turn
Turn
PRO3 mode setting
Press
Cancel
Press
Cancel
Data bank
load setting
function
Data bank
save setting
function
1CH
2CH
3CH
1CH
2CH
3CH
Press
Press
Press
Turn
Press
Press
Press
Press
Turn
Turn
PRO4 mode setting
Take care that if this product and the other digital fiber amplifiers are mounted in
cascade. The setting method is the same as well.
Press
Cancel
Press
Cancel
Data bank
load setting
function
Data bank
save setting
function
PRO5 mode setting
(Note 1)
Press Press
Press
Press
Turn
Turn
(Blinking)
: Confirmed
Press
: Select the
desired code
(Note 2)
Turn
Code
setting
function
Press
Goes to 'RUN' mode
after blinking twice.
Press
Cancel
Adjust lock ON
Adjust lock OFF
Press
Press
Press
Turn
Turn
Setting
reset
function
Adjust lock
setting
function
Notes: 1)
2)
When any code other than the codes given in the code setting table below is used, ' - ' is
displayed.
The initial setting of the respose time for this product is 'H-SP', which is not in the code set-
ting table, as shown below. Thus, the factory setting is displayed as ' '.
When the code setting function is used, refer to the 'Code setting table' given below.
KEY LOCK FUNCTION
14
٨If the jog switch and MODE key are pressed for more than 2 sec. at the same time
in 'RUN' mode condition, the key operations are locked, and only the threshold
value confirmation function or the adjust function (valid only when the adjust lock
function is canceled) is valid.
To cancel the lock function, press both the keys for more than 2 sec. once again.
3)
4)
In order to change PRO mode setting to 'RUN' mode, press MODE key for 2 sec. or more.
The response time 'H-SP' cannot be set by using the code setting function.
㧙㧙㧙㧙㧙㧙㧙㧙 㧙 5s
㧙㧙㧙㧙㧙㧙㧙㧙 㧙 4s
㧙㧙㧙㧙㧙㧙㧙㧙 㧙 3s
㧙㧙㧙㧙㧙㧙㧙㧙 㧙 2s
㧙㧙㧙㧙㧙㧙㧙㧙 㧙 1s
㧙㧙 㧙㧙㧙 㧙
㧙㧙 㧙㧙㧙 㧙
OFF
1ms
5ms
10ms
30ms
50ms
100ms
300ms
500ms
3ms
Direct
code
Direct 
EQFG
Direct 
EQFG
NON
OFF-delay
OFF-delay
ON-delay
ON-delay
ONE-SHOT
ONE-SHOT
ON
NONOFF
OFF
OFF
OFF
ON
ON
ON
L-ON
L-ON
L-ON
L-ON
H-02 (standard)
H-03 (large)
H-03 (large)
H-01 (small)
digit
D-ON
D-ON
D-ON
D-ON
digit
Percent
Percent
Peak hold
Peak hold
Bottom hold
Bottom hold
STD
H-02 (standard) S-D
H-02 (standard) LONG
H-02 (standard) FAST
FAST
FAST
H-03 (large) LONG
H-01 (small)
H-01 (small)
LONG
STD
STD
1st figure 2nd figure 3rd figure 4th figure
Timer
operation
Direct 
EQFG Timer
Adjust
lock
L-ON/
D-ON Display
Response
time
Hyste-
resis
Code setting table
The 0-ADJ setting function in this product was removed from production starting May, 2005.
INTENDED PRODUCTS FOR CE MARKING
15
٨The models listed under ' SPECIFICATIONS' come with CE Marking.
As for all other models, please contact our office.
1
Overseas Sales Division (Head Office)
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Phone: [phone] FAX: [phone]
Europe Headquarter: Panasonic Electric Works Europe AG
Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany
Phone: [phone]
US Headquarter: Panasonic Electric Works Corporation of America
629 Central Avenue New Providence, New Jersey 07974 USA
Phone: [phone]
PRINTED IN JAPAN © Panasonic Electric Works SUNX Co., Ltd. 2010
http://panasonic-electric-works.net/sunx