Panasonic KX-TG8280FX User manual

PQQW15559ZA DC0807DK0
FX-2/4
Connections
Connecting the telephone line cord
■To connect to a 2-line telephone jack
■To connect to 2 single-line telephone jacks
Connecting the AC adaptor
USE ONLY a 4-wire
telephone line cord.
To 2-line telephone jack
4-wire cord
“GREEN” plug
To single-line telephone jacks
2-wire cord 4-wire cord
Line 1
Line 2
“GREEN” plug
“Transparent”
plug
USE ONLY the supplied AC adaptor.
Insert the AC adaptor plug until a short beep sounds.
(220–240 V, 50 Hz)
Press plug firmly.
Hook
Digital Cordless Answering System
Model No. KX-TG8280FX
Quick Guide
To use this unit in your country, first change the unit’s region setting to match your
country. Change the unit’s display language as needed.
Refer to “Changing the unit’s region setting” in the operating instructions.
TG8280FX(e-e)_QG.fm Page 1 Wednesday, August 29, 2007 3:56 PM
All manuals and user guides at all-guides.com
all-guides.com

– 2 –
Battery installation/Battery charge
Initial charge: 7 hours
Note:
LUSE ONLY rechargeable Ni-MH batteries.
LDo NOT use Alkaline/Manganese/Ni-Cd batteries.
Screen saver mode
The backlight will turn off completely after 1 minute
of inactivity if the handset is not on the base unit. Press
{ih} to turn the display on again.
Operating tips
Using the handset navigator key
Press {^}, {V}, {<}, or {>}to navigate
through menus and to select items shown
on the display.
Adjusting the receiver or speaker
volume
Press {^} or {V} while on a call.
Handset menu icons
When in standby mode, pressing the middle soft key reveals the handset’s main
menu. From here you can access various features and settings.
Handset soft keys
The handset features 3 soft keys. By
pressing a soft key, you can select the
feature shown directly above it
on the display.
Rechargeable
Ni-MH ONLY
“Charging” will
be displayed.
{ih}
{V}
{^}
{<}{>}
jCaller List
JRinger Setup
IAnswer System
NHandset Setup
LBase Unit Setup
MDisplay Setup
Volume up
Volume down
TG8280FX(e-e)_QG.fm Page 2 Wednesday, August 29, 2007 3:56 PM
All manuals and user guides at all-guides.com

– 3 –
Display language
17 display languages are available.
You can select “Deutsch”, “English”, “Türkçe”, “Magyar”, “Polski”,
“SlovenČina”, “ČeŠtina”, “Hrvatski”, “Slovenscina”, “Eesti”,
“LIETUVIŠKAI”, “LatvieŠu”, “Românã”, “БЪЛГАРСКИ”, “Srpski”,
“МАКЕДОНСКИ”, or “Shqip”.
1{ih} i"
2Select Nby pressing {^}, {V}, {<}, or {>}. i#
3Press {^} or {V} to select “Display Setup”. i#
4Press {^} or {V} to select “Select Language”. i#
5Press {^} or {V} to select the desired language. i#i{ih}
Note:
LIf you select a language you cannot read: {ih} i"iNi#i{V}
2 times i#i{V} 3 times i#i{^}/{V}: Select the desired
language. i#i{ih}
Dialling mode (tone/pulse)
1"(middle soft key)
2Select Lby pressing {^}, {V}, {<}, or {>}. i#
3Press {^} or {V} to select “Call Options”. i#
4Press {^} or {V} to select “Dial Mode”. i#
5Press {^} or {V} to select the desired setting. i#i{ih}
Date and time
1"(middle soft key)
2Select Nby pressing {^}, {V}, {<}, or {>}. i#
3Press {^} or {V} to select “Time Settings”. i#
4Press {^} or {V} to select “Set Date & Time”. i#
5Enter the current date, month, and year.
6Enter the current hour and minute.
7#i{ih}
TG8280FX(e-e)_QG.fm Page 3 Wednesday, August 29, 2007 3:56 PM
All manuals and user guides at all-guides.com

– 4 –
Basic operations (Handset)
CMaking/Answering calls
Making calls Dial the phone number. i{C}/{s}
Answering calls {C}/{s}
Hanging up {ih}
Receiver/speaker volume Press {^} or {V} while on a call.
Making a call using the redial
list
{R} i{^}/{V}: Select the desired number. i
{C}
Temporary tone dialling
(for rotary/pulse service
users)
1Make a call.
2Press {*} when prompted to enter your code or
PIN, then press the appropriate dial keys.
Handset ringer volume 1"(middle soft key) iNi#
2{^}/{V}: “Ringer Setup”i#
3{^}/{V}: “Ringer Volume”i#
4{^}/{V}: “Line1”or “Line2”i#
5{^}/{V}: Select the desired volume. i#i
{ih}
kPhonebook
Adding entries (names and
phone numbers)
1{k} i"
2{^}/{V}: “New Entry”i#
3Enter the party’s name (16 characters max.). i
#
4Enter the party’s phone number (24 digits max.).
i#
5{^}/{V}: Select the desired category. i#
6{^}/{V}: “Save”i#i{ih}
LTo enter a name, see the character table in the
operating instructions.
Making calls 1{k}
2{^}/{V}: Select the desired entry. i{C}
TG8280FX(e-e)_QG.fm Page 4 Wednesday, August 29, 2007 3:56 PM
All manuals and user guides at all-guides.com

– 5 –
IAnswering system
Answering on 1"(middle soft key) iIi#
2Press Rrepeatedly to select the desired
line(s).
3{^}/{V}: “Answer On”i#i{ih}
Answering off 1"(middle soft key) iIi#
2{^}/{V}: “Answer Off”i#i{ih}
Listening to messages 1"(middle soft key) iIi#
2{^}/{V}: “Play New Msg.”or “Play All
Msg.”i#
Basic operations (Base unit)
CMaking/Answering calls
Making calls {SP-PHONE}iDial the phone number.
Answering calls {SP-PHONE}
Hanging up {SP-PHONE}
Speaker volume Press {^} or {V} while on a call.
Last number redial {SP-PHONE}i{REDIAL}
Temporary tone dialling
(for rotary/pulse service
users)
1Make a call.
2Press {*} when prompted to enter your code or
PIN, then press the appropriate dial keys.
Base unit ringer volume Press {^} or {V} when receiving a call.
LTo turn the ringer volume off, press and hold {V}
until the beep sounds.
IAnswering system
Answering on Press {LINE SELECT}repeatedly to select the
desired line(s). i{ANSWER ON}
L{ANSWER ON}lights up.
Answering off {ANSWER ON}
L{ANSWER ON}turns off.
Listening to messages {MESSAGE}
TG8280FX(e-e)_QG.fm Page 5 Wednesday, August 29, 2007 3:56 PM
All manuals and user guides at all-guides.com

– 6 –
Frequently asked questions
Question Cause & solution
Why is wflashing? LThe handset is too far from the base unit. Move
closer.
LThe base unit AC adaptor is not connected.
Check the connections.
LYou are using the handset or base unit in an area
with high electrical interference. Place the
handset and base unit away from interference
sources, such as antennas and mobile phones.
LThe handset is not registered to the base unit.
Register it (page 8).
Why can I not make calls? LThe dialling mode setting is incorrect. Set to
“Tone”or “Pulse”as needed (page 3).
Why is the handset display
blank?
LThe handset is in screen saver mode. Press
{ih} to activate the handset display again.
What should I do when the
handset does not turn on?
LMake sure that the batteries are installed
correctly.
LFully charge the batteries.
LClean the charge contacts and charge again.
How long is the battery
operating time?
LWhen you are using fully-charged Ni-MH batteries
(supplied batteries);
In continuous use: 12 hours max.
In continuous standby mode: 150 hours max.
LIt is normal for batteries not to reach full capacity
at the initial charge. Maximum battery
performance is reached after a few complete
cycles of charge/discharge (use).
LActual battery performance depends on a
combination of how often the handset is in use
and how often it is not in use (standby).
Can I keep the handset on
the base unit when I am not
using it?
LEven after the handset is fully charged, the
handset can be left on the base unit without any ill
effect on the batteries.
When should I replace the
batteries?
LIf the batteries are fully charged until 1is
displayed, but 3is displayed after a few calls,
replace the batteries with new ones.
What is a PIN? LThe PIN is a 4-digit number that must be entered
in order to change certain base unit settings. The
default PIN is “0000”.
TG8280FX(e-e)_QG.fm Page 6 Wednesday, August 29, 2007 3:56 PM
All manuals and user guides at all-guides.com
all-guides.com

– 7 –
What do I need to do to
display caller information?
LYou need to subscribe to Caller ID service.
Consult your service provider/telephone company
for details.
LThe message “You must first subscribe
to Caller ID.”will be displayed until you
receive caller information after subscribing to
Caller ID service.
What should I do when:
– I hear static or sound cuts
in and out?
– there is interference from
other electrical units?
LPlace the handset and the base unit away from
other electrical appliances.
LMove closer to the base unit.
LYour unit is connected to a telephone line with
DSL service. We recommend connecting a filter
(contact your DSL service provider) to the
telephone line between the base unit and the
telephone line jack.
What should I do when the
operating time seems to be
short even after I fully
charged the batteries?
LWipe the battery ends (S, T) and the unit
contacts with a dry cloth.
What do I need to do to
erase y(Missed call) from
the display?
LThere are unviewed missed calls remaining. View
them using the following method.
1"(middle soft key) iji #
2Press {V} to search from the most recent call,
or press {^} to search from the oldest call.
Frequently asked questions
Question Cause & solution
TG8280FX(e-e)_QG.fm Page 7 Wednesday, August 29, 2007 3:56 PM
All manuals and user guides at all-guides.com

– 8 –
Registering a handset to the base unit
The supplied handset and base unit are pre-registered. When you purchase an
additional handset, refer to the additional handset’s installation manual for
registration. If for some reason the handset is not registered to the base unit, register
the handset.
1"(middle soft key) iNi#
2{^}/{V}: “Register H.set”i#
3Press and hold {INTERCOM}on the base unit
for about 3 seconds, until the registration tone
sounds.
4Wait until “Enter Base PIN”is displayed.
iEnter the base unit PIN (default: “0000”).
i#
Optional service (Caller ID)
If you subscribe to Caller ID service, you can:
– display caller information
– identify who is calling by using different display colours and
ringtones (handset phonebook category)
"/#
{INTERCOM}
#
012345
012345
TG8280FX(e-e)_QG.fm Page 8 Wednesday, August 29, 2007 3:56 PM
All manuals and user guides at all-guides.com