Panasonic AW-PB506AN User manual

Before attempting to connect, operate or adjust this product,
please read these instructions completely.
Studio SDI Card
AW-PB506AN
This product consists of an SDI card and an
interface bracket.
F0806Y1116 DVQTB0136

- 2 -
indicates safety information.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(service) instructions in the literature accompanying the appliance.
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
FCC Note:
This equipment has been tested and found to comply with the limits for a class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Warning:
To assure continued FCC emission limit compliance, the user must use
only shielded interface cables when connecting to external units. Also, any
unauthorized changes or modifications to this equipment could void the user’s
authority to operate it.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class A est conforme à la norme
NMB-003 du Canada.
For CANADA
Safety precautions

- 3 -
indicates safety information.
WARNING:
• TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
• TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, KEEP THIS
EQUIPMENT AWAY FROM ALL LIQUIDS. USE AND STORE ONLY IN
LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OF DRIPPING OR
SPLASHING LIQUIDS, AND DO NOT PLACE ANY LIQUID CONTAINERS ON
TOP OF THE EQUIPMENT.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING
INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER CHANGES OF
SWITCH SETTINGS INSIDE THE UNIT TO QUALIFIED SERVICE PERSONNEL.
Safety precautions

- 4 -
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near
water.
6) Clean only with dry cloth.
7) Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
8) Do not install near any heat
sources such as radiators, heat
registers, stoves, or other
apparatus (including amplifiers)
that produce heat.
9) Do not defeat the safety purpose
of the polarized or grounding-
type plug. A polarized plug has
two blades with one wider than the
other. A grounding-type plug has
two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety.
If the provided plug does not fit
into your outlet, consult an
electrician for replacement of the
obsolete outlet.
10) Protect the power cord form being
walked on or pinched particularly
at plugs, convenience receptacles,
and the point where they exit from
the apparatus.
11) Only use attachments/accessories
specified by the manufacturer.
12) Use only with the cart,
stand, tripod, bracket,
or table specified by
the manufacturer, or
sold
with the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during
lightning storms or when unused
for long periods of time.
14) Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.
Read these operating instructions carefully before using the unit. Follow the safety
instructions on the unit and the applicable safety instructions listed below. Keep
these operating instructions handy for future reference.
IMPORTANT SAFETY
INSTRUCTIONS
indicates safety information.
Safety precautions

- 5 -
Contents
Configuration ........................................ 5
Accessories .......................................... 5
Introduction ........................................... 6
Characteristics ...................................... 6
Precautions for use .............................. 6
Major operating controls and
their functions ................................. 7
SDI card ........................................... 7
Interface bracket .............................. 8
Installing the SDI card .......................... 9
Interface bracket mountings ............. 10
Mounting the bracket on a tripod ... 10
Mounting the camera ..................... 10
Mounting the viewfinder
on a bracket................................ 10
Connections ........................................ 11
When configuring a system
with the remote control unit ....... 11
 When configuring a system
with the remote operation panel ... 12
Setting and changing of menu items ... 13
Performing the settings .................. 13
Optional card settings submenu .... 15
Appearance ......................................... 16
SDI card ......................................... 16
Interface bracket ............................ 17
Specifications ..................................... 18
Accessories
Adjuster plug (M6 M3) ......................... 1
Screws (6 mm) ....................................... 2
Screws (8 mm) ....................................... 4
Configuration
SDI card (AW-PB506A U01) ................... 1
Interface bracket (AW-PB506A U02) .... 1

- 6 -
Characteristics
 Two signal outputs for SDI signals
compliant with the SMPTE259M standard
[BELDEN 8281 or equivalent coaxial
cable; max. 656 ft. (200 m)]
EDH (Error Detection and Handling)
flags complying with the SMPTE RP165
standard can be added.
(A switch can be used to enable or
disable the addition of these flags.)
An inter-communications headset can be
used and its volume adjusted.
 The STANDBY/ON switch function of
the viewfinder (WV-VF65B, AW-VF80) is
incorporated.
Output signals (brightness and
composite video signals) to the
viewfinder can be switched using the
menu settings.
Zebra pattern and safety zone displays
appearing in the viewfinder can be
switched using the menu settings.
 The VIDEO ON/OFF switch function of
the viewfinder (AW-VF64) is incorporated.
(In order to prevent CRT burn-in, the
AW-VF64 does not come with a standby
function.)
Introduction
Installing the SDI card in a convertible
camera (such as the AW-E350, AW-E650,
AW-E655, AW-E750 and AW-E860) and
mounting the camera on the interface
bracket makes it possible for a viewfinder
and/or inter-communications headset to
be used and thus enable the camera to
be used as a studio camera. In addition,
there are two signal outputs for SDI signals
compliant with the SMPTE259M standard.
Notes
The AW-PB506A cannot be installed
to the following models;
AW-E300, AW-E300A, AW-E300S,
AW-E600, AW-E800, AW-E800A,
AW-RP605, AW-PB605
When the SDI card unit is to be
discarded at the end of its service
life, ask a specialized contractor
to dispose of it properly in order to
protect the environment.
When connecting or disconnecting a
cable from any unit, ensure that the
power to that unit is turned off.
Do not drop this product or subject it to
strong shock or vibration, as this may
cause it to malfunction.
Avoid using the unit in very humid or
dusty locations, as this may cause it to
malfunction.
Avoid using the product at a cold place
below 14°F (–10°C) or at a hot place
above 113°F (+45°C) because extremely
low or high temperature will adversely
affect the parts inside.
Precautions for use

- 7 -
Major operating controls and their functions
SDI card
EVF I/F connector [EVF I/F]
The EVF I/F cable 9from the interface
bracket is connected here.
SDI output 1, 2 connector
[SDI OUT 1, 2]
SDI signals are output from here.
Setting switches
SW NO OFF ON
1 EDH ENABLE DISABLE
2 SETTING E350 E860
3 DATA CLIP NORMAL CLIP
4 NTSC/PAL NTSC PAL
1: EDH <ENABLE/DISABLE>
(Factory setting: ENABLE)
An EDH flag is added to SDI output at
the ENABLE setting.
2: Model selection <E350/E860>
(Factory setting: E350)
When the AW-E350, AW-E650,
AW-E655 or AW-E750 is used, set
this switch at the E350.
When the AW-E860 is used, set this
switch at the E860.
3: DATA CLIP <NORMAL/CLIP>
(Factory setting: NORMAL)
At the NORMAL setting, signal input
is output at the same level at which it
was input.
At the CLIP setting, signal input at
less than 0% is output at 0%, and
signal input at more than 100% is
clipped at 100%.
4: NTSC/PAL switching <NTSC/PAL>
(Factory setting: NTSC)
Leave this switch at the factory setting.

- 8 -
Major operating controls and their functions
Interface bracket
EVF connector 1 [EVF1]
The viewfinder (WV-VF65B, AW-VF80)
is connected here.
5EVF connector 2 [EVF2]
The viewfinder AW-VF64 is connected
here.
Note
Do not connect EVFs to EVF
connectors 1 and 2 (and 5) at
the same time.
6EVF standby / VIDEO ON/OFF
switch
[ST.BY / VIDEO ON/OFF]
<For the WV-VF65B, AW-VF80>
ST.BY: Places the viewfinder in standby
mode.
ON: Outputs images to the viewfinder.
<For the AW-VF64>
VIDEO ON: Outputs images to the
viewfinder.
VIDEO OFF: No images appear on the
viewfinder.
The AW-VF64 does not come with a
standby function.
7 Inter-communications level control
[LEVEL]
This adjusts the sound level output to
the inter-communications headset.
8Inter-communications jack (M3)
[INCOM]
The inter-communications headset is
connected here.
If the plug diameter does not match, use
the adjuster plug (M6 M3) supplied
with this product.
MIC: Dynamic (With Preamp)
50 /–20 dB
Receiver: 150 (max. 200 mW)
9EVF I/F cable
This is connected to the EVF I/F
connector on the SDI card.
TALLY input connector [TALLY IN]
This is the tally control external input
connector.
OPEN: TALLY OFF
SHORT: TALLY ON
When using the AW-CB400 remote
operation panel and AW-CA50T8G
control cable for connecting to the
convertible camera, connect the TALLY
cable of the AW-CA50T8G to this
connector.

- 9 -
Installing the SDI card
Always ask your local dealer to install the SDI card.
Rear panel
Optional card
slot cover
4 screws 5/16” (8 mm)
2 screws 1/4” (6 mm)
SDI card
1
Turn the power to the camera off
and remove any cables which are
connected to the power connector or
other connectors.
2
Loosen the 4 screws [5/16” (8 mm)]
on the rear panel of the camera, then
remove the panel itself.
3
Loosen the 2 screws [1/4” (6 mm)]
on the optional card slot cover, then
remove the cover.
4Align the SDI card with the guides and
insert it.
Ensure the card is fully inserted.
5
Firmly tighten the 2 screws [1/4” (6 mm)]
to the optional card slot.
6Firmly secure the rear panel with the
4 screws [5/16” (8 mm)].
Note
If the screws are misplaced, use
the extra screws supplied with this
product.
Before installing the SDI card:
Release the static carried in the body of the person to perform the installation.
Installation can be performed more safely if an anti-static wrist strap is worn.
Touching the card without first releasing this static may cause malfunctioning.
Do not allow the metal part of the card come in contact with any other metal parts.

- 10 -
Mounting the bracket
on a tripod
1
Mount the interface bracket on the
tripod. (Screw: 1/4 – 20UNC)
Mounting the camera
2
Mount the camera (in which the
SDI card has been installed) on the
interface bracket.
Fasten the fixing knob to firmly secure
the camera.
Mounting the viewfinder
on a bracket
3
Mount the mounting base that is
supplied to the viewfinder onto the top
of the interface bracket using the 2
screws provided.
(Mount the base securely so that it is
not unsteady.)
4Slide the viewfinder onto the mounting
base and tighten the fixing knob to
secure it firmly.
5
Connect the viewfinder cable to the
EVF connector 1 or 2 on the interface
bracket.
6Connect the EVF I/F cable from
the interface bracket to the EVF I/F
connector on the SDI card.
Interface bracket mountings
Fixing knob
Fixing knob
<WV-VF65B,
AW-VF80, etc.>
Fixing knob
<AW-VF64>
Mounting base
2 screws