Panasonic VIDEOALARM PODV7CWNS/PODV7CPNS User manual

for
Before attempting to connect or operate this product,
please read these instructions completely.
Installation
Instructions
Outdoor Dome Housings
PODV7CWNS/PODV7CPNS
®
Manufactured By:
81-IN3090
01/18/07

- 2 -
!
!
SAFETY PRECAUTIONS
IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instructions
should be read before the unit is operated.
2. Retain Instructions - The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the unit and in the operating
instructions should be adhered to.
4. Follow Instructions - All operating and user instructions should
be followed.
5. Electrical Connections - Only a qualified electrician should make
electrical connections.
6. Attachments - Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Cable Runs - All cable runs must be within permissible
distance.
8. Mounting - This unit must be properly and securely mounted to
a supporting structure capable of sustaining the weight of the
unit. Accordingly:
a. The installation should be made by a qualified service person,
and should conform to all local codes.
b. Care should be exercised to select suitable hardware to
install the unit, taking into account both the composition of
the mounting surface and the weight of the unit. Be sure to
periodically examine the unit and the supporting structure to
make sure that the integrity of the installation is intact. Failure
to comply with the foregoing could result in the unit separating
from the support structure and falling, with resultant damages
or injury to anyone or anything struck by the falling unit.
UNPACKING
Unpack carefully. Electronic components can be damaged
if improperly handled or dropped. If an item appears to have
been damaged in shipment, replace it properly in its carton
and notify the shipper.
Be sure to save:
1. The shipping carton and packaging material. They are the
safest material in which to make future shipments of the
equipment.
2. These Installation and Operating Instructions.
SERVICE
For service on Panasonic/Videolarm equipment contact:
Panasonic Technical Center
54 West Gude Dr.
Rockville MD 20850-1150
Phone: [phone]
Fax: [phone]
1-800-528-6747
9:00 AM - 5:00 PM EASTERN TIME
CAUTION: INSTALLATION BY
QUALIFIED PERSONNEL ONLY
The lightning ash with an arrowhead symbol,
within an equilateral triangle, is intended
to alert the user to the presence of non-
insulated "dangerous voltage" within the
product's enclosure that may be of sufcient
magnitude to constitute a risk of electric shock
to persons.
The exclamation point within an equilateral
triangleisintendedtoalerttheusertopresence
of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
PANASONIC TECHNICAL SUPPORT
CAUTION
RISK OF
ELECTRIC SHOCK!

- 3 -
!
!
ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY):
Power 24Vac, Class 2 Only
Total Power: 52 watts (camera not included)
Accessories (Heater/Blower): 52 watts
Heater: 50 watts
Blower: 2 watt
Camera Power: 26 watts
NOTE: This unit is designed for operation in an
upright position. Installing the housing
upside down may cause damage to
the internal equipment, and will void the
warranty.
Be sure the bracket is properly and securely mounted
to a supporting structure capable of rigidly holding
the weight of the entire unit.
GENERAL INSTRUCTIONS:
Tools Required: .100" Flat Head Screwdriver
Phillips Head Screwdriver
PODV7CWNS/PODV7CPNS
IP Ready Network Housing
IP Ready Network Housing with 24Vac input, wall mount
or pendant mounting, heater & blowers, WV-NS202 and
camera.
ASSEMBLING THE UNIT:
1. Remove content from all boxes.
Contents should include:
Main Housing Assembly
Either with wall mount or pendant bracket
Dome Assembly - Clear or Tinted
Do not remove the protective lm until the product is
assembled and installed.
3 Packet Assemblies

- 4 -
INSTALLATION of the WV-NV202 Camera
in the PODV7 Housing
Install the quick release plate on top of the spacers already
installed in the housing. Note the orientation of the bracket.
The securing tab must be facing the front of the housing.
Secure the quick release plate into the housing using the (4)
#8 bolts and star washers provided in the packet assembly.
1.
Twist camera to secure
Attach the Camera
to the quick release
plate. Attach safety
lanyard to the back
of the camera.
Position the camera
as shown below on
the quick release
plate and twist
clockwise.
(Please see Pansonic Operation Manual for additonal details.)
2.
Complete wiring connections. Connect the RJ45 network
cable to into the network input. Complete power
connections.
Finish camera installation by securing the safety
locking tab.
3.
4.
Front
Securing Tab
Power Port
-+

- 5 -
WIRING INSTRUCTIONS (OUTSIDE OF HOUSING)
Wiring Color Code Power and Control Inputs
POWER
1 Camera Power (24 VAC) Red
2 Camera Power (24 VAC) Orange
3 Heater and Blower Power (24 VAC) Yellow
4 Heater and Blower Power (24 VAC) Green
CONTROL
1 Alarm 1 Blue
2 Alarm 2 Violet
3 Alarm 3 Gray
4 Common White
(2) 40Va power transformers are provided with all outdoor units.
The unit is set up with (2) individual power inputs:
1. Accessory Power (yellow and green wire)
2. Camera Power (red and orange)
If you wish to provide a single power transformer it is
recommended that:
1. Be certain that you know the total power consumption of
the housing Heater (25 watts) + Blower (1 watt) + camera
pan/tilt (25 watts).
2. Check the supplied wiring chart (see below) to be sure that
you have the proper gauge wire for the distance that you
intend to run your power wires.
3. Bring power to the 3 and 4 position of the power connector
(yellow and green wire).
4. Jumper from the 1st position to the 3rd position and from
the 2nd position to the 4th position of the terminal block.
Be careful not to short between the yellow and green wires.
22
250
120
89
65
44
35
29
25
31
19
17
16
14
13
12
11
11
10
9
9
8
20
400
180
141
90
70
56
47
40
34
31
28
25
23
21
20
18
17
16
15
14
14
18
600
300
225
130
112
90
75
64
55
50
45
41
37
34
32
30
28
26
25
23
22
16
960
480
358
225
179
143
119
102
85
79
71
65
59
55
51
47
44
42
39
37
35
14
-
800
571
350
285
228
190
163
140
126
114
103
95
87
81
76
71
67
63
60
57
12
-
1300
905
525
452
362
301
258
215
201
181
164
150
139
129
120
113
106
100
95
90
10
-
-
1440
830
720
576
480
411
340
320
288
261
240
221
205
192
180
169
160
151
144
5.5
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
Maximum distance from transformer to load
Total vA
consumed
Wire Gauge
24V AC Wiring Distances
The following are the recommended maximum distances for 24 VAC
with a 10% voltage drop (10% is generally the maximum allowable
voltage drop for AC powered devices).
Maximum distance from transformer to load
NOTE: The total power consumption for the heater
and blower, PLUS the camera you choose,
need to be added together.
In this example, a 60VA AC24V is required.
Add 2 jumpers for
single power input
AC
24V
Power
Supply
Side
Wires from
Dome
Green
Yellow
Orange
Red
RJ45
BNC
(Large)
Power
(Small)
Alarms

- 6 -
!
Be sure the bracket is properly and securely mounted
to a supporting structure capable of rigidly holding
the weight of the entire unit.
INSTALLING THE HOUSING ASSEMBLY:
NOTE: This unit is designed for operation in an
upright position. Installing the housing
upside down may cause damage to
the internal equipment, and will void the
warranty.
INSTALLING PENDANT MOUNT
1. This unit includes a 1½" NPT housing for a standard 1½"
NPT pipe. The housing can be used with other brackets
designed with 1½" male pipe threads, such as the WM20G
wall mount bracket.
2. Attach the housing coupling.
Add thread
sealing tape
NOTE: Pipe threads should be clean and rust-
free. Use the Teon™tape included with
the housing on the threads.
Teon Tape
A small roll of Teon tape is provided with all pendant units.
3. Mount the housing assembly to the mounting bracket
and housing coupling. A safety cable is included with
the housing to temporarily hold it while making wiring
connections. Loop the safety cable over one of the set
screws on the housing coupling and make the appropriate
connections using the (2) screw-down connectors supplied.
4. Undo the safety cable and twist the housing onto the
housing coupling. Secure all (3) setscrews provided on the
housing coupling.
Set screws

- 7 -
3. Open the access door on the bottom of the wall mount
by loosening the screw nearest the mounting plate.
4. Attach the wires from the wall to the connector provided.
using the wiring color code chart as a guide.
5. Once all wiring connections are made, place the wires
inside the wall mount bracket and close the access door.
Secure with the screw removed earlier.
CONNECTING THE TRIM RING ASSEMBLY TO THE
HOUSING TOP:
1. Open the access door on the bottom of the wall mount by
loosening the screw nearest the mounting plate.
CARE AND CLEANING OF DOMES:
All RHW75 and RHP75 units include an optically clear
polycarbonate dome. The dome is an optical device and
should be handled with extreme care. Leave protective lm
on dome until product is fully assembled and installed. Even
though the dome is virtually unbreakable, it can be easily
scratched.
Clean only with a clean cotton cloth and warm water.
DO NOT use a strong solvent or cleanser!
Access panel
Remove dome by twisting counterclockwise
until it stops, then pull down
2. To attach trim ring align pins with keyhole slots and turn
clockwise about ½" (12mm). Secure (3) screw or use (3)
security screws and security tool provided.
INSTALLING WALL MOUNT
A wall mount bracket comes standard with this unit, and
a template is included to use as a guide for mounting the
bracKet to a wall.
1. Choose the desired location for installation and mark
the drill holes using the template. Screw (2) bolts (not
provided) about ¾ of the way into the (2) top holes. Run
approximately 8 of wiring out of the wall.
2. The wall mount bracket provided with the FDW7 includes
a location for conduit entry. If you wish to install conduit to
the bracket remove the conduit hole plug. Install tting from
below the wall mount and secure with conduit nut from
inside the bracket.
NOTE: Be sure the hardware and the mounting
surface can support the weight of the
wall mount bracket plus the weight of the
housing and drive unit. The load will be
subjected to vibration from the camera
motor and wind.

- 8 -
Exploded View for Replacement Parts
16
18
(1)
(1)
(2)
(3)
(1)
19
11
10
6
5
4
7
8
9
2
3
12
1
13
14
15
17

- 9 -
Part Number Description
1 RPRH702 Lower Trim Ring (White)
2 RC7C Clear Replacement Capsule
RC7T Tinted Replacement Capsule
3 RPRH726 Spacing Ring
4 RPRH703 Clamping Ring
5 RPFD072 24VAC Heater
6 RPRH707 Connection PCB
7 RPFD060 Camera Bracket
8 RPFD040 Upper Bracket Assembly
9 RPRH709 Housing Top
10 RPFD2612 Housing Top Gasket
11 WM10 Wall Mount Bracket (Black)
12 RPFD080 12VDC Blower (Used on 24VAC Units)
13 RPNET02 24 to 12DC Power Supply
14 RP-FDJV-2000 Power Supply Bracket
15 RPPKPODV 1” spacers (set of 4)
16 SD0160 Pendent Mount Bracket
17 SD0170 Pendent Housing Coupling
18 RPPKE1125 Electrical Connector Packet
19 RPPKH2100 Housing Hardware Packet – Security Screws
Replacement Parts List

- 10 -
2.000
3.250
R .733
2.132
2.981
1.537
5.500
Mounting Template