Panasonic WVRM70 - ACCESSORY User manual

Camera Controller
WV-RM70
Before attempting to connect or operate this product,
please read these instructions completely.


WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the pres-
ence of uninsulated "dangerous volt-
age" within the product's enclosure that
may be of sufficient magnitude to con-
stitute a risk of electric shock to per-
sons.
The exclamation point within an equi-
lateral triangle is intended to alert the
user to the presence of important oper-
ating and maintenance (servicing)
instructions in the literature accompa-
nying the appliance.
The serial number of this product may be found on the bot-
tom of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of your
purchase to aid identification in the event of theft.
Model No.
Serial No.
Warning:
This equipment generates and uses radio frequency energy
and if not installed and used properly, i.e., in strict accor-
dance with the instruction manual, may cause harmful
interference to radio communications. It has been tested
and found to comply with the limits for a Class A computing
device pursuant to Subpart J of Part 15 of FCC Rules,
which are designed to provide reasonable protection
against such interference when operated in a commercial
environment.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SER-
VICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PER-
SONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SA 1965
SA 1966
For U.S.A
CAUTION:
Before attempting to connect or operate this prod-
uct, please read the label on the bottom.

-1-
CONTENTS
PREFACE ...................................................................................................................................................................... 2
FEATURES .................................................................................................................................................................... 2
PRECAUTIONS ............................................................................................................................................................. 3
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ....................................................................................... 4
CONNECTIONS ............................................................................................................................................................ 7
OPERATING PROCEDURE ........................................................................................................................................... 13
SPECIFICATIONS ......................................................................................................................................................... 32

-2-
PREFACE
The WV-RM70 Camera Controller, when combined with
the optional WV-CP610 and WV-BP510 series CCTV
Camera, enables remote control of camera settings.
Also it is available to receive the alarm (motion detec-
tor) signal multiplexed with the video signal from the
WV-CP610 and WV-BP510 series camera.
FEATURES
The WV-RM70 Camera Controller enables remote con-
trol of the following functions:
• Remote control of camera settings for the WV-
CP610 and WV-BP510 series camera, including
Electronic Sensitivity Up, Electronic Shutter, and
more.
• Remote control of camera and auxiliary equipment,
by using optional receiver and accessories, includ-
ing:
1. Remote control of Pan/Tilt Head and Camera
Housing.
2. Remote control of Motorized Zoom Lens :
Focus, Zoom and Iris.
Also it is available to receive the alarm (motion detec-
tor) signal multiplexed with the video signal from the
WV-CP610 and WV-BP510 series camera.

-3-
PRECAUTIONS
• Do not attempt to disassemble the unit.
In order to prevent electric shock, do not remove
screws or covers. There are no user-serviceable
parts inside.
Do refer to all servicing to qualified service person-
nel.
• Handle the unit with care.
Do not abuse the unit. Avoid striking, shaking, etc.
It could be damaged by improper handling or stor-
age.
• Do not expose the unit to rain or moisture, or try to
operate it in wet areas.
Do take immediate action if the unit becomes wet.
Turn the power off and refer servicing to qualified
service personal. Moisture can damage the unit
and also create the danger of electric shock.
• Do not use strong or abrasive detergents when
cleaning the unit body.
Do use a dry cloth to clean the unit when dirty.
In case the dirt is hard to remove, use a mild deter-
gent and wipe gently.
• Do not operate the unit beyond its temperature,
humidity or power source ratings.
Do not use the unit in an extreme environment
where high temperature or high humidity exist. Use
the unit under conditions where temperatures are
within 14˚F-140˚F (−10˚C - +60˚C) and humidity is
below 90%.
The input power source is 12V DC (10.8 - 16.0V
DC).
Caution: To prevent fire or shock hazard, the UL list-
ed wire VW-1, style 1007 should be used for the
cable for DC12V Input Terminal.

-4-
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
REMOTE OPERATE
Camera Controller WV-RM 70
PROG ALARM
RESET
NORMAL
SYSTEM
ALARM OFF
ON OFF
INOUT
TERM VIDEO CAMERA DC12V IN
GNDGND
ALARM OUT
RESET OUT DATA
T(A) T(B) R(A) R(B)
qw e r t y u i o !0 !1 !2 !3 !4 !5 !6

-5-
1. Power Indicator (OPERATE)
This indicator lights up when DC power is supplied
to the DC 12V Input Terminal.
2. Remote Indicator (REMOTE)
This indicator lights up when this controller is con-
trolled remotely by Personal Computer.
3. Left Switch (A)
This switch is used to move the cursor (in the
Setup Menu) in the left direction or move the
Pan/Tilt Head toward the left direction.
4. Down Switch (C)
This switch is used to move the cursor (in the Setup
Menu) in the down direction or move the Pan/Tilt
Head toward the down direction.
5. Up Switch (D)
This switch is used to move the cursor (in the Setup
Menu) in the up direction or move the Pan/Tilt Head
toward the up direction.
6. Set Switch
The mode selected in the setup menu is enabled
by pressing this switch.
7. Right Switch (B)
This switch is used to move the cursor (in the Setup
Menu) in the right direction or move the Pan/Tilt
Head toward the right direction.
8. Mode Selection Switch
(NORMAL/ALARM OFF/SYSTEM)
This switch is used to select the activated mode.
Refer to the Mode Selection on page 13 for more
details.
9. Program Switch (PROG)
This switch is used to display the Program Menu on
the monitor screen by pressing this switch for more
than 2 seconds,
10. Alarm Reset Switch (ALARM RESET)
When the unit is in the alarm mode, this indicator
starts blinking. Press this switch to cancel alarm
and the indicator light turns off.
11. Alarm Terminal
RESET OUT: When the controller resets the acti-
vated alarm by pressing the Alarm Reset
Switch, the alarm reset output signal is provid-
ed at this terminal for the Time Lapse VCR.

-6-
ALARM OUT: The alarm output signal is provided
at this terminal for the Time Lapse VCR.
12. Data Terminal
These terminals are used to transmit / receive
control data to / from a Personal Computer. Use
data grade cable, suitable for RS-485 (2 shielded,
twisted pairs), cable length may be extended up to
4,000 ft. (1,200m).
DesignationDirection
T (A) Personal Computer ←Controller
T (B) Personal Computer ←Controller
GND
R (A) Personal Computer →Controller
R (B) Personal Computer →Controller
GND
13. Termination Switch (TERM ON/OFF)
This switch is used to enable termination of this
controller’s data terminal.
14. Video Output Connector (VIDEO OUT)
A 1.0 Vp-p / 75Ωcomposite video signal is provid-
ed at this connector.
15. Camera Input Connector (CAMERA IN)
This connector accepts either a color or B/W com-
posite video signal from the camera. Also, VD2, to
synchronize camera in vertical timing, and data, to
control camera site devices, are multiplexed
through this connector.
16. DC 12V Input Terminal (DC 12V IN)
This terminal accepts 12V DC (10.8 - 16.0V DC)
power source.
Cautions :
1. Connect to a 12V DC class 2 power supply only.
2. To prevent fire or shock hazard, the UL listed
wire VW-1, style 1007 should be used for the
cable for DC 12V Input Terminal.

-7-
CONNECTIONS
1. Dip Switch Setting
Before connecting this controller, confirm the Dip
Switch Setting if the system setting change is required.
Pulse (VTR): +5V DC approx. 500msec.
Initially, VTR position is selected at the factory.
2. Set switch (SW2) on the board to choose the char-
acter display mode on the monitor.
NOR : White with Black border
REV : Black with White border
Initially, normal (NOR) position is selected at the
factory.
OPC
VTR
REV
NOR REV
NOR
SW1
SW2
SW5
SW3
SW4
Front
Rear
1. Set switch (SW1) on the board to
choose the alarm reset output sig-
nal as either Open Collector (OPC)
or Pulse (VTR).
Open Collector (OPC) :
16V DC 100mA max.
3. Confirm switches (SW3) on the
board are set to the position as
shown. These switches are used
only for factory test.
4. Confirm switch (SW4) on the
board is set to the "VS" position.
This switch is used only for fac-
tory test.
1234
OFF
VD VS

-8-
5. Set switch (SW5) on the board to choose the data
line selection mode for data terminal.
4 LINE : normal connections are
made.
2 LINE : simplified connections
are made.
Initially, 4 LINE is selected
at the factory.
The above switching should be made by qualified
service personal or system installers.
2. Connection of Alarm Output Terminal
• Make sure the polarity of the buzzer to meet with
this terminal.
The positive (+) terminal of
the buzzer should be con-
nected with the Alarm Output
Terminal.
• The Alarm Output Terminal is
composed of the Open
Collector Output and the
capacity is 16V DC, 100mA
or less.
2LINE
4LINE
GND
ALARM OUT
RESET OUT
(1) In case the buzzer is operable within the capacity
of Alarm Output Terminal, connect buzzer as
shown right.
(2) In case the buzzer is not operable within the
capacity of Alarm Output Terminal, the external
relay unit should be used as shown below.
GND
ALARM OUT
RESET OUT
NC NO
+12V
C
NC : Normally Closed
NO : Normally Open
C : Common
To Buzzer
Relay
Buzzer