Panasonic H-FS35100PP User manual

file:///C|/U...emp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_cvr.xml[11/12/2018 11:45:29 AM]
Order No.DSC1410024CE
B26
Interchangeable Lens for Digital Camera
Model No. H-FS35100PP
H-FS35100E
H-FS35100GK

file:///C|/U...emp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_cvr.xml[11/12/2018 11:45:29 AM]
© Panasonic Corporation 2014 Unauthorized copying and distribution is a violation of law.

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_01.xml[11/12/2018 12:04:27 PM]
1 Service Navigation
1.1 Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.

1.2 Important Notice
1.2.1 About LENS MAIN UNIT (Ref. 209)
1. 
lens adjustments.

2. 
202), to maintain Serial number of owner's original lens.
3. No adjustment is required when replacing the part mentioned on Fig.1-1. But, when tighten the concerned screws,apply proper torque
mentioned on "4. Disassembly and Assembly Instruction" section.

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_02.xml[11/12/2018 12:04:59 PM]
2 Operating Guide
2.1 Before Use
(Information for Your Safety)
2.2 Cautions For Use

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_02.xml[11/12/2018 12:04:59 PM]
2.3 Components

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_02.xml[11/12/2018 12:04:59 PM]
2.3.1 Accessories
2.3.2 Attaching/Detaching the Lens

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_02.xml[11/12/2018 12:04:59 PM]
2.3.3 Recording Preparations and How to Retract the Lens

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_02.xml[11/12/2018 12:04:59 PM]

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_03.xml[11/12/2018 12:05:36 PM]
3 Service Fixture & Tools
3.1 Service Fixture and Tools
The following Service Fixture and Tools are used for Checking & Servicing for this unit.
3.2 Clean Box

10,000 (Federal Standard 209D).
[NOTE]


file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_04.xml[11/12/2018 12:18:31 PM]
4 Disassembly and Assembly Instructions
4.1 Outline
It is recommended dealing with clean box, to keep maintaining the dustproof environment.
(Refer to“3.2. Clean Box”section of this service manual for details.)
Important:
1. 

As for procedure, refer to the “5 Maintenance” for details.
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with lens caps (front & rear), other
than necessary cases.
3. 
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
Proceed disassemble/assemble, by referring the following table and Fig. W1.
NOTE:
1. 
following table.
2. It's unnecessary to remove/install B210 for disassembly and assembly.
3. Use small driver (VFK1390) when removing/tightening B206.
Interchangeable Lens (H-FS35100)

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_04.xml[11/12/2018 12:18:31 PM]

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_04.xml[11/12/2018 12:18:31 PM]
4.2 Disassembly procedure
Important:


4.2.1 Removal of the Decoration Ring
1. Decoration ring is sticked on the 1st lens frame unit.
2. Put the sheet so that the lens glass is fully covered.
3. 
4.2.2 Removal of the Filter ring
1. Remove the 3 screws (A).

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_04.xml[11/12/2018 12:18:31 PM]
4.2.3 Removal of the Shading frame
1. Remove the 3 screws (B).
4.2.4 Removal of the L mount unit
1. Remove 1 screw (C) and 3 screws (D).

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_04.xml[11/12/2018 12:18:31 PM]
4.2.5 Removal of the Rear farme unit
1. After removing 3 screws (E), remove the Rear farme unit.
And, remove the Adjust pin.
4.2.6 Removal of the Lens P.C.B.unit and the Mount contact unit

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_04.xml[11/12/2018 12:18:31 PM]
1. After discconecting 3 connectors, remove the Lens P.C.B.unit and the Mount contact unit.
4.2.7 Removal of the Mount contact unit
1. Disconnect 1 connector.
4.2.8 Removal of the 7th lens frame unit
1. Remove 3 screws (F).
4.2.9 Removal of the Zoom drive pin

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_04.xml[11/12/2018 12:18:31 PM]
1. Remove 1 screw (G).
4.2.10 Removal of the Ring mount base unit
1. Remove 3 screws (H).
4.2.11 Removal of the 1st lens holder unit and the Cam barrel unit
1. Rotate the Cam barrel unit clockwise when you watch it from back.

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_04.xml[11/12/2018 12:18:31 PM]
4.3 Assembly procedure
Important:

4.3.1 Installation of the Filter ring
1. 
(Torque Driver : RFKZ0456)
(Torque : 7±1N cm)
4.3.2 Installation of the Decoration ring
1. Please insert the pins of the Decoration ring to the holes of the Filter ring.
Use new one, do not use the one which is removed.
Double-stick tape sticks to the Decoration ring of therepair part.
Please remove the old double-stick tape from the Lenstop unit.
2. After installing the Decoration ring, use a soft cloth to press it into place.

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_04.xml[11/12/2018 12:18:31 PM]
4.3.3 Installation of the 1st lens holder unit and the Cam barrel unit
1. Align phase marks( ) and rotate the Cam barrel unit unticlockwise when you watch it from back.
4.3.4 Installation of the Ring mount base unit
1. 
(Torque Driver : RFKZ0456)
(Torque : 7±1N cm)

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_04.xml[11/12/2018 12:18:31 PM]
4.3.5 Installation of the Zoom drive pin
1. 
(Torque Driver : RFKZ0456)
(Torque : 9±1N cm)
4.3.6 Installation of the 7th lens frame unit
1. 
(Torque Driver : RFKZ0456)
(Torque : 7±1N cm)

file:///C|/U...Temp/Rar$EXa0.493/viewing/SGML_VIEW_DATA/ALL/H-FS35100PP/SVC/DSC1410024CE/doc/DSC1410024CE_04.xml[11/12/2018 12:18:31 PM]
4.3.7 Installation of the Mount contact unit
1. Connect FPC to 1 connector.
4.3.8 Installtionl of the Lens P.C.B.unit and the Mount contact unit
1. Connect FPCs to 3 connectors.
4.3.9 Installation of the Rear frame unit
1. After inserting the Adjust pin, install the Rear farme unit.