Panasonic CN-NVD905U - Strada - Navigation System User manual

© 2007 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and distribu-
tion is a violation of law.
ORDER NO. ACED070301C1
C7
AUTOMOTIVE AFTERMARKET
CN-NVD905U
Dual DIN in-dash HDD Mobile Naviga-
tion System with 7”Widescreen Color
LCD Monitor/DVD Receiver
TABLE OF CONTENTS PAGE PAGE
1 Service Navigation----------------------------------------------- 2
2 Specifications ----------------------------------------------------- 3
3 Features ------------------------------------------------------------- 4
4 Technical Descriptions----------------------------------------- 5
5 Adjustment --------------------------------------------------------22
6 Block Diagram----------------------------------------------------24
7 Wiring Connection Diagram ---------------------------------29
8 Schematic Diagram---------------------------------------------30
9 Schematic Diagram-2 ------------------------------------------44
10 Printed Circuit Board-------------------------------------------49
11 Exploded View and Replacement Parts List -----------62
12 Schematic Diagram for Printing with Letter Size-----87

2
1 Service Navigation
1.1. About Lead Free Solder (PbF)
Distinction of PbF PCB :
• PCBs (manufactured) using lead free solder will have a PbF
stamp on the PCB.
Caution :
• Pb free solder has a higher melting point than standard sol-
der; Typically the melting point is 50 - 70°F (30 - 40°C)
higher. Please use a soldering iron with temperature control
and adjust it to 700 ± 20°F (370 ± 10°C). In case of using
high temperature soldering iron, please be careful not to
heat too long.
• Pb free solder will tend to splash when heated too high
(about 1100°F/600°C)
• This lead free solder will be used for the products after serial
No. 1,000,001.
1.2. Laser Products
1.3. Replacing the Fuse
Use fuses of the same specified rating 15 amps. Using different
substitutes or fuses with higher ratings, or connecting the unit
directly without a fuse, could cause fire or damage to the stereo
unit.
1.4. Maintenance
Your product is designed and manufactured to ensure a mini-
mum of maintenance. Use a dry, a soft cloth for routine exterior
cleaning. Never use benzine, thinner or other solvents.
1.5. Notes
[RADIO BLOCK]
Do not align the AM/FM package block. When the package
block is necessary, it will be supplied already aligned at the fac-
tory.
[DVD DECK BLOCK]
This model has no servo alignment points because microcom-
puter controls the servo circuit.

3
2 Specifications
2.1. Specifications*
2.2. Dimensions
General
Power Supply DC 12V (11V - 16V)
Test Voltage 14.4V
Negative Ground
Current Consumption Less than 10A
Maximum Power Output 50W ×4ch
Compatible speaker imped-
ance 4Ω
Video input signal NTSC1.0 Vp-p
(75ΩRCA pin jack)
Audio input sensitivity Stereo 2.0 Vrms
(RCA pin jack)
Camera input NTSC1.0 Vp-p
(75Ω5Pin connector)
Video output signal NTSC1.0 Vp-p
(75ΩRCA pin jack)
Pre-Amp output voltage 2.0 Vrms
Pre-amp Output impedance Less than 600 Ω
Dimensions (W×H×D)** 178×100×165mm
(7”×3-15/16"×6-1/2")
Weight** 3.1 kg (6 lbs. 14 oz)
Audio section
Output voltage/Impedance 2.0 Vrms/600Ω
Frequency characteristics
Front L/R, Center, Rear L/R 20 Hz -20 kHz (±1 dB)
Distortion 0.01 %
(1kHz, 0dB, PCM input)
Dynamic range 96 dB
S/N Ratio 100dB
FM tuner
Frequency Range 87.7 MHz - 107.9 MHz
Usable Sensitivity 12.2 dBf
S/N Ratio 63 dB
Stereo Separation 40 dB (at 1 kHz)
AM tuner
Frequency Range 530 kHz - 1710 kHz
Usable Sensitivity
(S/N Ratio 20dB) 26 dB/µV
Image Rejection Ratio 50 dB
Monitor
Liquid crystal panel 7” wide
Screen dimensions
(W ×H ×D) 156 ×82 ×176 mm {6 1/8” ×3 3/16” ×6 7/8”}
Number of pixels 336 960 pixels
(234 vertical ×480 horizontal ×3)
Valid pixel ratio Over 99.99 %
Display method Transparent color filter format
Drive method TFT (Thin Film Transistor)
active matrix format
Light source Internal light (Built-in small uores-
cent lamp)
Touch Panel Pressure-sensitive touch panel, ana-
log type (film & glass)
GPS antenna
Type Microstrip
Cord length 6 m
Dimensions (W×H×D) 30.4×11.7×35.5mm
(1-13/64"×15/32"×1-13/32")
Weight (lncluding cord) 113g (4 oz)
Frequency Range 1,575.42MHz (C/A cord)
Receiving Sensitivity -130 dBm
Receiving method Parallel 8 ch
* Specifications and the design are subject to possible modification
without notice due to improvements.
** Dimensions and Weight shown are approximate.
** Above specifications comply with EIA standards.

4
3 Features
• High performance Navigation
- Near the intersection
- Add a destination
- Detour routes
- Autoroute
•Easytouse
- High usability and easy understand GUI
- Navigation menu
- Destination menu
- Information menu
- Setup menu
• AV features
- Various AV sources
- DVD/ CD/ MP3/ WMA/ FM/ AM
- Expansion Module (The optional Hub unit: CY-EM100U)
- Connectable Optional devices
- Controllable iPod/software version (Feb., 2007)
3rd generation iPod/ver. 2.2 - 2.3
4th generation iPod/ver. 3.0.2 - 3.1
5th generation iPod/ver. 1.0
(Video and photos cannot be displayed.)
iPod Photo/ver. 1.0 - 1.2
(Photos cannot be displayed.)
iPod mini/ver. 1.2 - 1.4
iPod nano/ver. 1.0
- Direct cable for iPod (CA-DC300U, option)
- Optional XM Satellite Radio Tuner (XMD1000)
- Optional Digital Adapter Cable (XMDPAN110)
- Optional SIRIUS Satellite Radio Tuner (SIR-PAN1)
- Bluetooth hands-free kit (CY-BT100U, option)
- Over-Head monitor (CY-VHD9401U, option)
- TV tuner (CY-TUN153U, option)
- Rear view camera

5
4 Technical Descriptions
4.1. Terminals Description
4.1.1. Main Block
IC600 : C2DBYY000215
Pin
No Port Description I/O Vol [V]
FM AM CD DV
DNA VI TV
1NAVI
DET Pulled up - 5.0 5.0 5.0 5.0 5.0 5.0
2 RD CLK Not connected - ------
3MDSO
(MI) Pulled up - 4.6 4.6 0.3 0.3 0.3 0.3
4MDSI
(MO) Not connected - ------
5 MD CLK Not connected - ------
6 EVDD +5V power supply - 555555
7EVSS Ground -000000
8 MD RST Not connected - ------
9 MD ON Not connected - ------
10 MD V
CNT Not connected - ------
11 MD 8V
CNT Not connected - ------
12 EEP SO Serial data from
EEPROM I000000
13 EEP SI Serial data to
EEPROM O000000
14 EEP SK Serial clock for
EEPROM O000000
15 EEP CS Chip select of
EEPROM O000000
16 NC Not connected - ------
17 NC Not connected - ------
18VPP VPPforFlashwriter -000000
19 PLL DI Serial data to tuner
PLL O 5.0 5.0 5.0 5.0 5.0 5.0
20 PLL CLK Clock for serial data
bus O 5.0 5.0 5.0 5.0 5.0 5.0
21 PLL DO Tuned station detec-
tion I------
22 SWF1
SEL Frequency shift selec- tion for DC/DC con-
verters 1
O000000
23 SWF2
SEL Frequency shift selec- tion for DC/DC con-
verters 2
O000000
24 LED CNT Panel LEDs control O 5.0 5.0 5.0 5.0 5.0 5.0
25 LED2
CNT Not connected - ------
26 CAMP
CNT Not connected - ------
27 EX AMP
CNT External amplifier power supply control O 5.0 5.0 5.0 5.0 5.0 5.0
28 AMP
CNT Power amplifier control O 5.0 5.0 5.0 5.0 5.0 5.0
29 AMP
MUTE Mute for Power ampli- fier O000000
30 AMP DET Anomalous DC offset
detection of Power
amplifier
I000000
31 RESET Reset I 5.0 5.0 5.0 5.0 5.0 5.0
32XT1 Ground -000000
33 XT2 Not connected - ------
34 REGC Connected to capacitor - 3.3 3.3 3.3 3.3 3.3 3.3
35 X2 Crystal OSC
(16.8MHz) - 1.5 1.5 1.5 1.5 1.5 1.5
36 XA Crystal OSC
(16.8MHz) - 1.4 1.4 1.4 1.4 1.4 1.4
37 VSS Ground - 000000
38 VDD +5V power supply - 5.0 5.0 5.0 5.0 5.0 5.0
39 CLK OUT Not connected - - - - - - -
40 ANT
CONT Antenna power supply control O 5.0 5.0 5.0 5.0 5.0 5.0
41 TFT NMI Power control in TFT
PCB O 5.0 5.0 5.0 5.0 5.0 5.0
42 MAIN
CNT Main power control O 4.9 4.9 4.9 4.9 4.9 4.9
43 MDC
PWR Power control for Panel motor O 5.0 5.0 5.0 5.0 5.0 5.0
44 MA Panel motor control
(Forward) O000000
45 MB Panel motor control
(Reverse) O000000
46 MC Not connected - - - - - - -
47 NC Not connected - - - - - - -
48 NC Not connected - - - - - - -
49 NC Not connected - - - - - - -
50 NC Not connected - - - - - - -
51 NC Not connected - - - - - - -
52 NC Not connected - - - - - - -
53 NC Not connected - - - - - - -
54 PLL CE Not connected - - - - - - -
55 BVDD +5V power supply - 5.0 5.0 5.0 5.0 5.0 5.0
56 BVSS Ground - 000000
57 NC Not connected - - - - - - -
58 NC Not connected - - - - - - -
59 NC Not connected - - - - - - -
60AFMUTEAudiomute O000000
61 FMM
CNT Notconnected -------
62 FMM CE Not connected - - - - - - -
63 FMM
MUTE Notconnected -------
64 FMM
CLK Notconnected -------
65 FMM
DATA Notconnected -------
66 NC Not connected - - - - - - -
67 ASEL0 Analog audio line
selection 0 O000000
68 ASEL1 Analog audio line
selection 1 O000000
69 NC Not connected - - - - - - -
70 NC Not connected - - - - - - -
71 AVDD +5V power supply - 5.0 5.0 5.0 5.0 5.0 5.0
72 AVSS Ground - 000000
73 AVREF +5V power supply - 5.0 5.0 5.0 5.0 5.0 5.0
74 SD Signal level of AM and
FM I000000
75 INITIAL A Pulled up - 5.0 5.0 5.0 5.0 5.0 5.0
76 NOISE Tuner noise detection I 000000
77 BATT
SENS Battery level check I 4.9 4.9 4.9 4.9 4.9 4.9
78 T/O KEY Tilt/Open key detection I 5.0 5.0 5.0 5.0 5.0 5.0
79 P SEN-
SOR Position sensor of TFT panel I 0.1 0.8 0.8 0.8 0.8 0.8
80 L/R KEY Track up/down key
detection I 4.9 4.9 4.9 4.9 4.9 4.9
81U/DKEYPulleddown -000000
82 ACC
SENS ACC level check I 4.9 4.9 4.9 4.9 4.9 4.9
83 ST FM stereo detection I 5.0 5.0 5.0 5.0 5.0 5.0
Pin
No Port Description I/O Vol [V]
FM AM CD DV
DNA VI TV

6
4.1.2. Sub Block
IC503 : C2BBGF000764
84 MU/BA
KEY Pulleddown -000000
85 THM Temperature check I 2.6 2.6 2.6 2.6 2.6 2.6
86 SD IN1 From SD card I 5.0 5.0 5.0 5.0 5.0 5.0
87 SD IN2 From SD card I 5.0 5.0 5.0 5.0 5.0 5.0
88PUSLEPulleddown -000000
89 MD
EJECT Pulled up - 4.9 4.9 4.9 5.0 5.0 5.0
90 VR A Pulled up - 5.0 5.0 5.0 5.0 5.0 5.0
91 VR B Pulled up - 5.0 5.0 5.0 5.0 5.0 5.0
92 NC Not connected - ------
93 LCD CE Not connected - ------
94 DI Serial data from Flash
writer I000000
95 DO Serial data to Flash
writer O 5.0 5.0 5.0 5.0 5.0 5.0
96 CLK Serial clock of Flash
writer O 5.0 5.0 5.0 5.0 5.0 5.0
97 SO RX Serial data from NAVI
PCB I 5.0 5.0 5.0 5.0 5.0 5.0
98 SO TX Serial data to NAVI
PCB O 5.0 5.0 5.0 5.0 5.0 5.0
99 RD SD Tuned station detec-
tion I 5.0 5.0 5.0 5.0 5.0 5.0
100 RD SDA Not connected - ------
Pin
No Port Description I/O Vol [V]
FM AM CD DV
DNA VI TV
1P15 Testterminal -000000
2 P16 Test terminal - 5.1 5.1 5.1 5.1 5.1 5.1
3 TILT OPEN key detection I 5.0 5.0 5.0 5.0 5.0 5.0
4 AVSS Ground - 000000
5 P130 Not connected -------
6 ST DET - - 3.8 3.8 3.8 3.8 3.8 3.8
7 AVREF1 +5V power supply - 5.1 5.1 5.1 5.1 5.1 5.1
8 SI2 Serial data from Digital
audio I 5.0 5.0 5.0 5.0 5.0 5.0
9 DAI SO Serial data to Digital
audio O000000
10 DAI CLK Clock for serial data
bus O 5.0 5.0 5.0 5.0 5.0 5.0
11 KO RXD Serial data from NAVI
PCB I 5.1 5.1 5.1 5.1 5.1 5.1
12 KO TXD Serial data to NAVI
PCB O000000
13 KO CLK2 Clock for serial data
bus I/O 5.1 5.1 5.1 5.1 5.1 5.1
14 CODC
RQ CODEC (IC500) request O 5.0 5.0 5.0 5.0 5.0 5.0
15 P24 FRAM chip selection O 5.0 5.0 5.0 5.0 5.0 5.0
16SI0 SerialdatafromFRAMI000000
17SO0 SerialdatatoFRAM O000000
18 SCK0 Clock for FRAM O 5.0 5.0 5.0 5.0 5.0 5.0
19 P40 Not connected -------
20 SYS
PWR System power control O 5.0 5.0 5.0 5.0 5.0 5.0
21 DCDC
INTRES CODEC (IC500) initial reset O 5.0 5.0 5.0 5.0 5.0 5.0
22 DCDC
SYSRES CODEC (IC500) sys- tem reset O 5.0 5.0 5.0 5.0 5.0 5.0
23 P44 Not connected -------
Pin
No Port Description I/O Vol [V]
FM AM CD DV
DNA VI TV
24 P45 Not connected - - - ----
25 P46 Not connected - - - ----
26 P47 Not connected - - - ----
27 DIR CS DIR (IC504) chip select O 5.0 5.0 5.0 5.0 5.0 5.0
28 DIR PDN DIR (IC504) power-
down control O 5.05.05.05.05.05.0
29 P52 Not connected - - - ----
30 P53 Not connected - - - ----
31 P54 Not connected - - - ----
32 P55 Not connected - - - ----
33 VSS1 Ground - 000000
34 P56 Not connected - - - ----
35 SYS
MUTE System mute O 0 0 0 0 0 0
36 P60 Not connected - - - ----
37 P61 Not connected - - - ----
38 P62 Reset for beacon sys-
tem O 5.05.05.05.05.05.0
39 P63 Not connected - - - ----
40 P64 Not connected - - - ----
41 P65 Not connected - - - ----
42 P66 Not connected - - - ----
43 P67 Not connected - - - ----
44 FV SEL0 Front video selection 0 O 000005.0
45 FV SEL1 Front video selection 1 O 000000
46 FV SEL2 Front video selection 2 O 5.0 5.0 0 0 5.0 0
47 RV SEL0 Rear video selection 0 O 000005.0
48 RV SEL1 Rear video selection 1 O 000000
49 RV SEL2 Rear video selection 2 O 5.0 5.0 0 0 5.0 0
50 SPD CNT Vehicle speed detec-
tion control O000000
51 SPD DET - I 5.0 5.0 5.0 5.0 5.0 5.0
52 SPD SEL - O 0 0 0 0 0 0
53 RSE OFF - O 5.0 5.0 5.0 5.0 5.0 5.0
54 IRDA
DET Pulled up - 5.0 5.0 5.0 5.0 5.0 5.0
55 P123 Not connected - - - ----
56 LEDON O 5.0 5.0 5.0 5.0 5.0 5.0
57 PKB OUT Parking brake detec-
tion I 0 0 5.0 5.0 5.0 5.0
58 P126 Not connected - - - ----
59SD - -000000
60 RESET Reset I 5.0 5.0 5.0 5.0 5.0 5.0
61 SEP VS0 Separated vertical
sync. I 5.05.05.05.05.05.0
62 STBREM
OUT STB (Set Top Box) remote control I000000
63 INTREQ Interrupt request I 5.1 5.1 5.1 5.1 5.1 5.1
64 +B DET Battery level check I 5.1 5.1 5.1 5.1 5.1 5.1
65 ACC DET ACC detection I 4.0 4.0 4.0 4.0 4.0 4.0
66 P05 Error detection of
unlocked PLL I 5.05.05.05.05.05.0
67 VSS0 Ground - 000000
68 VDD1 +5V power supply - 5.0 5.0 5.0 5.0 5.0 5.0
69 X2 Crystal OSC
(4.9152MHz) I 2.92.92.92.92.92.9
70 X1 Crystal OSC
(4.9152MHz) I 2.72.72.72.72.72.7
71 IC Pulled down - 0 0 0 0 0 0
72 XT2 Not connected - - - ----
73 XT1 Ground - 000000
74 VDD0 +5V power supply - 5.0 5.0 5.0 5.0 5.0 5.0
75 AVREF0 +5V power supply - 5.0 5.0 5.0 5.0 5.0 5.0
76VOUT2 - I000000
77 ANI1 Not connected - - - ----
Pin
No Port Description I/O Vol [V]
FM AM CD DV
DNA VI TV

7
4.1.3. TFT Block
IC407 : C2BBFD000652
78 P12 Switched battery
power supply I 2.7 2.7 2.7 2.7 2.7 2.7
79P13 Testterminal -000000
80P14 Testterminal -000000
Pin
No. Port Description I/O
1 VCC +5V power supply -
2 VREF +5V power supply -
3 AVSS Ground -
4 BL CNT TFT backlight control O
5 HPOS1 Horizontal display positive select 1 O
6 HPOS2 Horizontal display positive select 2 O
7 I2C DO Serial data to EEPROM O
8 WP Write protect for EEPROM O
9 INTEXT Internal or External for Flash writer O
10 MODE Mode control for Flash writer
11 TXD Serial data to NAVI PCB O
12 RXD Serial data from NAVI PCB I
13 I2C DI Serial data in TFT PCB I
14 I2C CLK Serial clock in TFT PCB O
15 CNVSS CNVSS from Flash writer I
16 TOUCH SW Touch switch control O
17 NC Not connected -
18 RESET Reset I
19 XIN Crystal OSC I
20 XOUT Crystal OSC O
21 VSS Ground -
22 BL ON Backlight power control O
23 ZOOM Not connected -
24 SIDE Not connected -
25 JUST Not connected -
26 X+ X-axis control for Touch panel O
27 X- X-axis control for Touch panel O
28 Y+ Y-axis control for Touch panel O
29 Y- Y-axis control for Touch panel O
30 LED TFT mode control O
31 TILT LED TFT mode control O
32 POW KEY Not connected -
33 VOL+ KEY Volume-up key detection I
34 VOL- KEY Volume-down key detection I
35 MENU KEY Map key detection I
36 AUDIO KEY Source key detection I
37 GENZ KEY Navigation key detection I
38 DIM Pulled down -
39 XR X-axis detection of Touch panel I
40 XG X-axis detection of Touch panel I
41 YR Y-axis detection of Touch panel I
42 YG Y-axis detection of Touch panel I
Pin
No Port Description I/O Vol [V]
FM AM CD DV
DNA VI TV

8
4.1.4. DVD Servo Block
IC501 : C1AB00002402
Pin No Port Description I/O (V)
1 VDDIO I/O pad power (3.3V) - 3.3
2 MD10 SDRAM data bus I/O 0
3 MD11 SDRAM data bus I/O 0.6
4 VDD Core power (1.8V) - 1.8
5 MD12 SDRAM data bus I/O 0
6 VSSIO I/O pad ground - 0
7 MD13 SDRAM data bus I/O 0.7
8 MD14 SDRAM data bus I/O 0.5
9 MD15 SDRAM data bus I/O 0
10 VDDIO I/O pad power (3.3V) - 3.3
11 /DQM1 SDRAM data byte enable O 0
12 MA9 SDRAM address bus O 0
13 MA8 SDRAM address bus O 0
14 VSSIO I/O pad ground - 0
15 MA7 SDRAM address bus O 2.3
16 MA6 SDRAM address bus O 1.9
17 VSS Core ground - 0
18 MA5 SDRAM address bus O 1.1
19 VDDIO I/O pad power (3.3V) - 3.3
20 MA4 SDRAM address bus O 2
21 MA3 SDRAM address bus O 2.3
22 MCLK SDRAM clock O 1.7
23 VSSIO I/O pad ground - 0
24 CKE SDRAM clock enable O 3.3
25 MA2 SDRAM address bus O 2.3
26 MA1 SDRAM address bus O 1
27 VDDIO I/O pad power (3.3V) - 3.3
28 MA0 SDRAM address bus O 1
29 MA10 SDRAM address bus O 0
30 MA11 Not used - -
31 VSSIO I/O pad ground - 0
32 MA12 SDRAM address bus O 2.1
33 MA13 SDRAM address bus O 2.1
34 VDD Core power (1.8V) - 1.8
35 /CS0 SDRAM primary bank chip
select O2.7
36 VDDIO I/O pad power (3.3V) - 3.3
37 /RAS SDRAM command bit O 3.1
38 /CAS SDRAM command bit O 2.9
39 /WE SDRAM command bit O 3.2
40 VSSIO I/O pad ground - 0
41 /DQM0 SDRAM data byte enable O 0
42 /DQM2 SDRAM data byte enable O 0
43 MD16 SDRAM data bus I/O 0.5
44 VDDIO I/O pad power (3.3V) - 3.3
45 MD17 SDRAM data bus I/O 0.5
46 MD18 SDRAM data bus I/O 0.5
47 VSS Core ground - 0
48 MD19 SDRAM data bus I/O 0.7
49 VSSIO I/O pad ground - 0
50 MD20 SDRAM data bus I/O 0
51 MD21 SDRAM data bus I/O 1.5
52 MD22 SDRAM data bus I/O 1
53 VDDIO I/O pad power (3.3V) - 3.3
54 MD23 SDRAM data bus I/O 0
55 MD24 SDRAM data bus I/O 0.5
56 MD25 SDRAM data bus I/O 0.5
57 VSSIO I/O pad ground - 0
58 MD26 SDRAM data bus I/O 0.5
59 MD27 SDRAM data bus I/O 0.8
60 MD28 SDRAM data bus I/O 0
61 MD29 SDRAM data bus I/O 1
62 VDDIO I/O pad power (3.3V) - 3.3
63 MD30 SDRAM data bus I/O 0.7
64 MD31 SDRAM data bus I/O 0.5
65 /DQM3 SDRAM data byte enable O 0
66 /CS1 Not used O -
67 VSSIO I/O pad ground - 0
68 SPDIF S/PDIF digital audio output O 1.3
69 VSS Core ground - 0
70 AIN Digital audio input for digital
micro I3.3
71 AOUT3 Serial audio data (Left/Right CH) O 0
72 AOUT2 Serial audio data (Center/LFE
CH) O0
73 AOUT1 Serial audio data (Sound Left/
Right CH) O0
74 AOUT0 Serial audio data (Left/Right CH) O 0
75 VDDIO I/O pad power (3.3V) - 3.3
76 PCMCLK Audio DAC PCM sampling clock O 1.8
77 VDD Core power (1.8V) - 1.8
78 ACLK Audio interface serial data clock O 1.7
79 LRCLK Left/Right channel clock O 1.7
80 /SRST Reset signal O 3.3
81 /RSTP Power on reset I 3.3
82 VSSIO I/O pad ground - 0
83 RXD1 Not used - -
84 SSPIN1 SSP1 data in / UART1 16X clock I/O 15
85 VSS Core ground - 0
86 SSPOUT1 SSP1 sata out / UART1 DTR I/O 0
87 SSPCLK1 SSP1 clock / UART1 CTS I/O 3.3
88 SSPCLK0 Not used - -
89 VDD Core power (1.8V) - 1.8
90 SSIN0 Not used - -
91 VDDIO I/O pad power (3.3V) - 3.3
92 SSPOUT0 Not used - -
93 TXD0 UART0 serial data O 3.2
94 RXD0 UART0 serial data I 3
95 /CTS0 Not used - -
96 /RTS0 Not used - -
97 VSSIO I/O pad ground - 0
98 CXI Crystal Oscillator terminal I 1.6
99 CXO Not used - -
100 OSCVSS Oscillator ground - 0
101 OSCVDD Oscillator power (1.8V) - 1.8
102 MVCLVDD Main/Video clock PLL power
(3.3V) -3.3
103 SCEN Not used - -
104 MVCKVSS Main/Video clock PLL Ground - 0
105 ACLKVSS Audio clock PLL ground - 0
106 SCMD Not used - -
107 ACLKVDD Audio clock PLL power - 3.3
108 VDDDAC DAC digital power (1.8V) - 1.8
109 VSSDAC DAC digital ground - 0
110 CVBS2/CR/R Composite Cr/Component Cr/
SCART Red O0.5
111 IOM Cascaded DAC differential out-
put O1
112 C/CB/B Chrominance/Component Cb/
SCART Cb O0.7
113 VAA3 DAC analog power (3.3V) - 3.3
114 Y/G Luminance/SCART G O 0.4
115 VSSA DAC analog ground - 0
116 VREF Not used - -
117 VAA - - 1.8
118 CVBS/C Composite/S-Video Chromi-
nance O0.5
119 RSET Current setting resistor connec-
tion O1.4
120 COMP Compensation capacitor con-
nection O2
121 VSS Core ground - 0
Pin No Port Description I/O (V)

9
122 VCLK Not used - -
123 VSYNC Not used - -
124 HSYNC Not used - -
125 VDDIO I/O pad power (3.3V) - 3.4
126-131 VI07-02 Not used - -
132 VSSIO I/O pad ground - 0
133 Not used - -
134 Not used - -
135 VDD Core power (1.8V) - 1.9
136-139 AD31-28 Not used - -
140 VDDIO I/O pad power (3.3V) - 3.4
141-144 AD27-24 Not used - -
145 /PWE3 Not used - -
146 AD23 Not used - -
147 VSSIO I/O pad ground - 0
148-150 AD22-20 Not used - -
151-153 AD19-17 Address/Data bus I/O 0
154 VDDIO I/O pad power (3.3V) - 3.4
155 AD16 Address/Data bus I/O 0
156 /PWE2 Not used - -
157,158 AD15,14 Address/Data bus I/O 0
159 VDD Core power (1.8V) - 1.9
160 SCLK External bus clock O 2.1
161 ACK Programmable WAIT/ACK/RDY
control I3.4
162 VSSIO I/O pad ground - 0
163-168 AD13-08 Address/Data bus I/O 0
169 VDDIO I/O pad power (3.3V) - 3.4
170 /PWE1 Not used - -
171 VSS Core ground - 0
172-176 AD7-3 Address/Data bus I/O 0
177 VSSIO I/O pad ground - 0
178-180 AD02-00 Address/Data bus I/O 0
181 VDDIO I/O pad power (3.3V) - 3.4
182 /PWE0 Byte write enable O 0
183 ALE Address latch enable O 0
184-187 LA0-3 Latch address O 3.3
188 VSSIO I/O pad ground - 0
189 RD Read signal O 3.4
190 LHLDA Not used - -
191 LHLD Not used - -
192 VDD Core power (1.8V) - 1.9
193 /PCS0 Peripheral chip select 0 O 3.4
194 XI01 Not used - -
195 DACCS2 DAC output select 2 O 3.4
196 VDDIO I/O pad power (3.3V) - 3.4
197 DACCS1 DAC output select 1 O 3.4
198 NINTCPPM Not used - -
199 CPPMCS Not used - -
200 XI06 Not used - -
201 VSS Core ground - 0
202 FRAMCS FRAM chip selection O 0
203 DACRST DAC reset O 0
204 VSSIO I/O pad ground - 0
205 FEPCS Front End Pro. LSI chip select O 3.4
206 FEPRST Front End Pro. reset O 3.4
207 SODCCS SODC LSI chip selection O 3.4
208 NINTHOST HOST interrupt I 3.4
209 NINTDDC DDC interrupt I 3.2
210 VDDIO I/O pad power (3.3V) - 3.4
211 NINTDSC DSC interrupt I 3.5
212 VDD Core power (1.8V) - 1.9
213 DSYNV DVD parallel mode sector SYNC I 3.4
214 DREQ DVD parallel mode data request O 3.4
215 DCLK Data sampling clock I 3.4
216 DSTB Parallel mode data valid/Serial
mode clock I0.7
Pin No Port Description I/O (V) 217 DVD0 DVD drive parallel data port I 0
218 VSSIO I/O pad ground - 0
219 DVD1 DVD drive parallel data port I 0
220 DVD2 DVD drive parallel data port I 0
221 DVD3 DVD drive parallel data port I 3.4
222 DVD4 DVD drive parallel data port I 0.8
223 DVD5 DVD drive parallel data port I 0.8
224 VDDIO I/O pad power (3.3V) - 3.4
225 DVD6 DVD drive parallel data port I 3.4
226 DVD7 DVD drive parallel data port I 3.4
227 MD0 SDRAM data bus I/O 0.5
228 VSSIO I/O pad ground - 0
229 MD1 SDRAM data bus I/O 0
230 VSS Core ground - 0
231 MD2 SDRAM data bus I/O 0.8
232 MD3 SDRAM data bus I/O 0.8
233 VDDIO I/O pad power (3.3V) - 3.3
234 MD4 SDRAM data bus I/O 3.3
235 MD5 SDRAM data bus I/O 0
236 MD6 SDRAM data bus I/O 0.8
237 VSSIO I/O pad ground - 0
238 MD7 SDRAM data bus I/O 0
239 MD8 SDRAM data bus I/O 0
240 MD9 SDRAM data bus I/O 0
Pin No Port Description I/O (V)

10
4.2. IC Block Diagram
4.2.1. Main Block
IC51 : C0ABCB000077
IC106 : C0JBAZ002222
IC109 : C0CAAYG00005
IC181,720 : C0DBEKG00001
IC200 : C0JBAR000367
IC201,506,507 : C0ABCB000051
IC300 : C1ZAZ0001450
IC500 : C0FBZK000010

11
IC503 : C0FBAK000003
IC504 : C1BB00000634
IC505 : C0ABEB000066
IC508-510 : C0ABBB000263
IC511 : C0DBEGE00002
IC660 : C0JBAB000888
IC700 : AN8065S-E1V
IC710 : C1BB00000828
IC715,752 : AN77L05M-E1

12
IC1600 : C0GBG0000032
IC1603 : C0JBAM000156
4.2.2. Sub Block
IC100 : C0EBH0000550
IC101 : C1BB00000828
IC102 : C0EBB0000183
IC103,107,4001 : C0JBAA000261
IC106,216 : C0JBAB000379
IC108 : C0DBEKG00001
IC115 : C0DBAZG00025

13
IC207 : C0EBH0000520
IC319 : C0JBAR000367
IC320 : C0FBAG000014
IC321 : AN77L05M-E1
IC405 : C1AB00000164
IC406,407 : C0JBAZ002803
IC504 : C3GBCA000001
IC3005 : C0DBGYY00185
IC3007 : C0CBCAA00006

14
IC110,111 : C0DBAZD00009
IC761 : C0DBAZC00016
4.2.3. Navi/HDD Block
IC408,1117,1118 : C0JBAA000372
IC409 : C0JBAZ001492

15
IC201,202 : C3ABRG000059
IC102 : C0CBABA00020
IC205 : C0JBZZ000322
IC502 : C0FBBH000053
IC700 : C0JBAB000354
IC701 : C0JBAS000241

16
IC702 : C0ABBB000283
IC1101,1103,1124 : C0JBAB000629
IC1102,1104 : C0JBAB000824
IC1105,1108 : C0JBAZ002635
IC1106,1107,1110 : C0ABAA000099
IC1109 : C0DBEKG00001
IC1115 : C0JBAC000412
IC1116,1123 : C0JBAA000261
4.2.4. TFT/SW Block
IC402 : C1BB00000828
IC403 : AN77L03M-E1

17
IC404 : C3EBDC000049
IC405 : C0EBH0000520
IC406,603 : C0JBAA000372
IC408 : C1AB00002372
IC412 : C0JBAF000701
IC417 : YEAMM2107FT1
IC418 : C0DBEKG00001
IC421 : C0DBEJC00002
IC422 : C0JBAA000319
IC602 : C0EBC0000240

18
IC409 :C0JBAR000513
IC970 : PNA4S42M01MC
IC601 : C0DBAYY00280
IC401 : AN8049SH-E1V

19
IC415 : C1AB00002215
IC407 : C2BBFD000652

20
IC410 : AN2546FH-A
4.2.5. DVD Deck Block
IC101 : AN8703FH-V IC311 : C0GBY0000012