Panasonic KX-TG7100CX User manual

PQQW15248ZA DC0506DU0
Digital Cordless Phone
Model No. KX-TG7100CX
1Connections
2Battery installation/
Battery charge (Initial charge: 7 hours)
Note:
LUse only the included rechargeable batteries.
Quick Guide
(220–240 V, 50/60 Hz)
To telephone network
Hook
Use only the included AC adaptor
and telephone line cord.
Charge contact
TG7100CX(e-e)_QG.fm Page 1 Thursday, May 11, 2006 8:06 PM

–2 –
3Symbols used in these operating instructions
Dialling mode (tone/pulse)
1{j/OK}
2Press {^} or {V} to select “Base Unit Setup”. i{>}
3Press {^} or {V} to select “Call Options”. i{>}
4Press {^} or {V} to select “Dial Mode”. i{>}
5Press {^} or {V} to select the desired setting. i{>}i{ih}
Date and time
1{j/OK}
2Press {^} or {V} to select “Handset Setup”. i{>}
3Press {^} or {V} to select “Time Settings”. i{>}iPress {^} or {V} to select “Set
Date & Time”. i{>}
4Enter the current day, month, and year.
5Enter the current hour and minute.
6{j/OK}i{ih}
4Basic operations
Symbol Meaning
{j/OK}Press {j/OK}.
iProceed to the next operation.
“” Select the words in quotations shown on the display (e.g., “Handset
Setup”) by pressing {^} or {V}.
Feature Operation
Making a call Dial the phone number. i{C}/{s}
Answering a call {C}
Hanging up {ih}
Receiver/speaker volume Press {^} or {V} while on a call.
Last number redial {R} i{C}
Making a call with redial list {R} iPress {^} or {V} to select the desired
number. i{C}
TG7100CX(e-e)_QG.fm Page 2 Thursday, May 11, 2006 8:06 PM

–3 –
5Frequently asked questions
Handset phonebook: storing an
entry (name and phone
numbers)
{k} i{j/OK}i“New Entry”i{>}i
Enter the party’s name (16 characters max.). i
{j/OK}iEnter the party’s phone number (24 digits
max.). i{j/OK}i“Save”i{>}i{ih}
LTo enter a name, see the character table in the
operating instructions.
Handset phonebook: making a
call
{k} iPress {^} or {V} to display the desired entry.
i{C}
Handset ringer volume {j/OK}i“Handset Setup”i{>}i
“Ringer Setup”i{>}i“Ringer Volume”
i{>}iPress {^} or {V} to select the desired
volume. i{>}i{ih}
Changing ringtone
(outside calls)
{j/OK}i“Handset Setup”i{>}i
“Ringer Setup”i{>}i“Ext. Ringtone”
i{>}iSelect the desired ringtone. i{>}i
{ih}
Question Cause & solution
What kind of power outlet should
I connect the AC adaptor to?
Connect the AC adaptor to a 220–240 V outlet.
Why is wflashing? LThe handset is too far from the base unit. Move closer.
LThe AC adaptor is not connected. Check the
connections.
LYou are using the handset or base unit in an area with
high electrical interference. Place the handset and
base unit away from interference sources, such as
antennas and mobile phones.
LThe handset is not registered to the base unit.
Register it.
{j/OK}i“Handset Setup”i{>}i
“Registration”i{>}i“Register H.set”
i{>}iPress and hold {x} on the base unit for
about 3 seconds, until the registration tone sounds. i
Wait until “Enter Base PIN”is displayed. iEnter
the base unit PIN (default: “0000”). i{j/OK}
Why can I not make calls? The dialling mode setting is incorrect. Set to “Tone”or
“Pulse”as needed.
Why is the handset display
blank?
The handset is not turned on. To turn the power on,
press {ih} for about 1 second.
Feature Operation
TG7100CX(e-e)_QG.fm Page 3 Thursday, May 11, 2006 8:06 PM

–4 –
What should I do when the
handset does not turn on?
LMake sure that the batteries are installed correctly.
LFully charge the batteries.
LClean the charge contacts and charge again.
How long should I charge new
batteries?
Charge the batteries for about 7 hours.
How long is the battery operating
time?
When you are using fully-charged Ni-MH batteries
(included batteries);
In continuous use: 17 hours max.
In continuous standby mode: 180 hours max.
LIt is normal for batteries not to reach full capacity at the
initial charge. Maximum battery performance is
reached after a few complete cycles of charge/
discharge (use).
LActual battery performance depends on a combination
of how often the handset is in use and how often it is
not in use (standby).
Can I keep the handset on the
base unit when I am not using it?
LEven after the handset is fully charged, the handset
can be left on the base unit without any ill effect on the
batteries.
When should I replace the
batteries?
If the batteries are fully charged until
1 is displayed,
but 3 is displayed after a few calls, replace the
batteries with new ones.
What is a PIN? The PIN is a 4-digit number that must be entered in order
to change certain base unit settings. The default PIN is
“0000”.
What do I need to do to display
caller information?
LYou need to subscribe to Caller ID service. Consult
your service provider/telephone company for details.
LThe message “You must first subscribe to
Caller ID.” will be displayed until you receive caller
information after subscribing to Caller ID service.
Question Cause & solution
TG7100CX(e-e)_QG.fm Page 4 Thursday, May 11, 2006 8:06 PM

–5 –
6Optional service (Caller ID and SMS)
If you subscribe to Caller ID service, you can:
– display caller information
To use SMS, you must subscribe to Caller ID and/or appropriate service.
SMS (Short Message Service)
Tom
012345
TG7100CX(e-e)_QG.fm Page 5 Thursday, May 11, 2006 8:06 PM

TG7100CX(e-e)_QG.fm Page 6 Thursday, May 11, 2006 8:06 PM