Panasonic KX-TG8011E User manual

PNQW1899ZA DC0609DY0
Connections
Important:
LIf you use a telephone line cord which is not supplied, the unit may not work
properly.
(220-240 V AC, 50 Hz)
To telephone
line
DSL/ADSL filter
(For DSL/ADSL
service users)
Hook
Guide
Plug
“Click”
Use only the supplied Panasonic
AC adaptor PQLV207E.
Use only the supplied
telephone line cord.
Press plug firmly.
Plug
Guide
Do not try to connect over the guide.
Base unit
(KX-TG8012/KX-TG8013)
Charger
Use only the supplied Panasonic
AC adaptor PQLV209E.
Press plug firmly.
(220-240 V AC, 50 Hz)
Hooks
Model No. KX-TG8011E/KX-TG8012E
KX-TG8013E
Quick Guide
TG8011E(e)_QG.fm Page 1 Thursday, June 4, 2009 11:26 AM

– 2 –
Battery installation/Battery charge
Charge for about 7 hours.
Note:
LUSE ONLY Ni-MH batteries AAA (R03) size.
LDo NOT use Alkaline/Manganese/Ni-Cd batteries.
Screen saver mode
The backlight goes dark when on a call or
turns off completely after 1 minute of
inactivity if the handset is not on the base
unit or charger.
Activate the handset display again by:
–pressing{<}or {>}when on a call.
–pressing{ih} at all other times.
Base unit Charger *1
Rechargeable
Ni-MH ONLY
“Charging”is
displayed.
*1 KX-TG8012/KX-TG8013
{ih}
TG8011E(e)_QG.fm Page 2 Thursday, June 4, 2009 11:26 AM

– 3 –
Operating tips
Using the navigator key
The handset navigator key can be used to
navigate through menus and to select items
shown on the display by pressing {^}, {V},
{<}, or {>}.
To adjust the receiver or speaker volume,
press {^} to increase the volume, or press
{V} to decrease the volume repeatedly while
talking.
Soft keys
The handset features 3 soft keys. By
pressing a soft key, you can select the feature
shown directly above it on the display.
Menu icons
When in standby mode, pressing the middle soft key reveals the handset’s top-
menu. From here you can access various features and settings.
Date and time (Handset)
1K(middle soft key) iNiM
2{V}/{^}: “Time Settings”iM
3{V}/{^}: “Set Date & Time”iM
4Enter the current date, month, and year.
5Enter the current hour and minute.
6Mi{ih}
{V}
{^}
Volume up
Volume down
{<}{>}
Icon Feature
jCaller List
JRinger Setup
KTime Settings
Icon Feature
NHandset Setup
<Base Unit Setup
|Display Setup
TG8011E(e)_QG.fm Page 3 Thursday, June 4, 2009 11:26 AM

– 4 –
Basic operations
Making/Answering calls (Handset)
Making calls Dial the phone number. i{C}/{s}
Answering calls {C}/{s}
To hang up {ih}
To adjust the receiver/
speaker volume
Press {^} or {V} repeatedly while talking.
Making a call using the redial
list
j(right soft key) i{V}/{^}: Select the desired
phone number. i{C}
Handset ringer volume 1K(middle soft key) iNiM
2{V}/{^}: “Ringer Setup”iM
3{V}/{^}: “Ringer Volume”iM
4{V}/{^}: Select the desired volume. iMi
{ih}
Phonebook (Handset)
Adding entries 1n(left soft key) iK
2{V}/{^}: “New Entry”iM
3Enter the party’s name (16 characters max.).
iM
LYou can change the character entry mode by
pressing /.
4Enter the party’s phone number (24 digits max.).
iM
5{V}/{^}: Select the desired category.
iM2timesi{ih}
LTo enter a name, see the character table in the
operating instructions.
Making calls 1n(left soft key)
2{V}/{^}: Select the desired entry.
LYou can scroll through the phonebook entry by
pressing and holding {V} or {^}.
3{C}
TG8011E(e)_QG.fm Page 4 Thursday, June 4, 2009 11:26 AM

– 5 –
Frequently asked questions
Question Cause/solution
Why is wflashing? LThe handset is too far from the base unit. Move
closer.
LThe base unit’s AC adaptor is not connected.
Check the connections.
LYou are using the handset or base unit in an area
with high electrical interference. Re-position the
base unit and use the handset away from sources
of interference.
LThe handset is not registered to the base unit.
Register it (page 7).
Why is the handset display
blank or goes dark when on
a call?
LThe handset is in screen saver mode. Activate the
handset display again by:
– pressing {<}or {>}when on a call.
– pressing {ih} at all other times.
L“LCD Dimming”is set to “Off”while on charge.
Change the setting.
What should I do when the
handset does not turn on?
LMake sure the batteries are installed correctly.
LFully charge the batteries.
LClean the charge contacts and charge again.
How long is the battery
operating time?
LWhen you are using fully-charged Ni-MH batteries
(supplied batteries);
In continuous use: 14 hours max.
Not in use (standby): 240 hours (10 days) max.
LIt is normal for batteries not to reach full capacity
at the initial charge. Maximum battery
performance is reached after a few complete
cycles of charge/discharge (use).
LActual battery performance depends on a
combination of how often the handset is in use
and how often it is not in use (standby).
Can I keep the handset on
the base unit or charger
when I am not using it?
LEven after the handset is fully charged, the
handset can be left on the base unit or charger
without any ill effect on the batteries.
When should I replace the
batteries?
LIf the batteries are fully charged until 1is
displayed, but 3is displayed after a few calls,
replace the batteries with new ones.
What is a PIN? LThe PIN is a 4-digit number that must be entered
in order to change certain base unit settings. The
default PIN is “0000”.
TG8011E(e)_QG.fm Page 5 Thursday, June 4, 2009 11:26 AM