Panasonic KX-TGC210BL User manual

© Panasonic System Networks Co., Ltd. 2015
Unauthorized copying and distribution is a violation
of law.
ORDER NO. KM41506860SE
Telephone Equipment
Model No.
KX-TGC210BL/KX-TGC212BL/
KX-TGC213BL/KX-TGC222BL/
KX-TGC210CX/KX-TGC212CX/
KX-TGC210HK/KX-TGC212HK/
KX-TGC210TU/KX-TGC210TW/
KX-TGC212TW/KX-TGC210BX/
KX-TGC212BX/KX-TGC220BX/
KX-TGC222BX/KX-TGC210UE/
KX-TGC212UE/KX-TGC213UE/
KX-TGC220UE/KX-TGC222UE/
KX-TGC210ML/KX-TGC212ML/
KX-TGC210GR/KX-TGC210SL/
KX-TGC222SL/KX-TGC210NL/
KX-TGC212NL/KX-TGC213NL
Digital Cordless Phone
Digital Cordless Answering System
B: Black Version S: Silver Version
C: Blue Version W: White Version
TABLE OF CONTENTS
PAGE PAGE
1 ORIGINAL SERVICE MANUAL INFORMATION --------- 2
2 REPLACEMENT PARTS LIST--------------------------------- 2
2.1. REFERENCE CHART------------------------------------ 2
2.2. ORIGINAL AND NEW PARTS COMPARISON
LISTS --------------------------------------------------------- 3
3 CHANGES----------------------------------------------------------- 4
3.1. Things to Do after Replacing IC or X'tal ------------- 4
4 ADDITION------------------------------------------------------------5
4.1. VES (Virtual EEPROM Storage) LAYOUT
(Handset)-----------------------------------------------------5
4.2. How to update the BBIC.---------------------------------6
Supplement
Please use this manual with the original service manual mentioned on the next page.

2
1 ORIGINAL SERVICE MANUAL INFORMATION
Handset: For Suffix B or Later
2 REPLACEMENT PARTS LIST
2.1. REFERENCE CHART
Model No. on S/M Destinations Order No. of S/M Suffix Code
Base Unit Handset
KX-TGC210BL/KX-TGC212BL/KX-TGC213BL/KX-TGC222BL/KX-
TGC210CX/KX-TGC212CX/KX-TGC210HK/KX-TGC212HK/KX-
TGC210TU/KX-TGC210TW/KX-TGC212TW/KX-TGC210BX/KX-
TGC212BX/KX-TGC220BX/KX-TGC222BX/KX-TGC210UE/KX-
TGC212UE/KX-TGC213UE/KX-TGC220UE/KX-TGC222UE/KX-
TGC210ML/KX-TGC212ML/KX-TGCA20EX/KX-TGCA20BX/KX-
TGCA20CX/KX-TGCA20HK/KX-TGCA20TW/KX-TGCA20ML
BL=for Belgium, CX=for Sin-
gapore, Vietnam, Indonesia,
HK=for Hong Kong, TU=for
Tunisia, Algeria, Morocco,
TW=for Taiwan, BX: for Iran,
Yemen, Pakistan, Ghana, Lib-
yan Arab, Mauritius, Lebanon,
Bahrain, UE=for UAE, Nigeria,
Kuwait, Qatar, ML=for Malaysia
KM41408855CE A to B A to B
KX-TGC210FX/KX-TGC210PD/KX-TGC210SL/KX-TGC210NL/KX-
TGC210GR/KX-TGC212FX/KX-TGC212NL/KX-TGC213NL/KX-
TGC222SL/KX-TGCA20EX/KX-TGCA20FX
FX=for Czech, Slovakia, Esto-
nia, Latvia, Lithuania, Croatia,
Slovenia, Rumania, Bulgaria,
Albania, Bosnia and Herzegov-
ina, Serbia, Egypt, Jordan,
Oman, Barclay, The Former
Yugoslav Republic of Mace-
donia, PD=for Poland, Hun-
gary, SL=for Switzerland,
NL=for Netherlands, GR=for
Greece
KM41406843CE A to B A to B
Reason for Change
*The following items (1-8) indicate the reason for change. See the “Notes” column for each part in ORIGINAL AND NEW PARTS
COMPARISON LISTS.
1. Improve performance Note:
Change parts based on Suffix Code.
Remarks:
*c: To share the parts with other models
2. Change of material or dimension
3. To meet approved specification
4. Standardization
5. Addition
6. Deletion
7. Correction
8. Other

3
2.2. ORIGINAL AND NEW PARTS COMPARISON LISTS
Serial No.Label tells you the suffix code as follows.
Note:
*1: Please refer to "1 ORIGINAL SERVICE MANUAL INFORMATION".
Note:
The shape of IC is different in the old one and the new one.
Suffix A B BSerial No. Label
(Example)
Ref. No. Part No. Part Name & Description Pcs/
Set
Remarks Notes Time of Change
Original (Old) New (Suffix)
Main P.C.Board Parts (Handset)
IC7 PNWIGCA20EXR ---------- IC (EEPROM) 0 *c 6 V *1
IC4 C3FBLY000162 PNWIACA20EXR IC 1 *c 8 V *1
RA5 EXB28V332JX ---------- RESISTOR ARRAY 0 *c 6 V *1
C69 ECUE1A104KBQ ---------- CAPACITOR, 0.1F 0 *c 6 V *1
F1 K5H252Y00002 ERJ3GEY0R00 RESISTOR, 01*c8V *1

4
3 CHANGES
3.1. Things to Do after Replacing IC or X'tal
3.1.1. Handset
[Changed from original section “11.6.1.2. Handset”]
First, operate the PC setting according to The Setting Method of JIG.
Then download the appropriate data according to the following procedures.
Note:
(*2) WW: country code, XXX_YYY: revision number
“XXX_YYY” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in The Setting
Method of JIG.
Items How to download/Required adjustment
FLASH(IC4)
[for Suffix B or Later]
Adjusted parameter data is
stored in memory.
(country version batch file,
default batch file,ect)
1) Please be sure to execute the following steps if you have replaced the FLASH
IC(IC4).
1. Update BBIC. Refer How to update the BBIC.
2. Detach the JIG cable, then disconnect the battery.
3. Insert battery.
4. Connect the JIG cable again, and execute the command "getchk", then con-
firm the checksum value is correct.
• If the downloading failes, start again from step 1.
5. Check DECT ID written on Plastic bag of FLASH (IC4).
6. Execute the command "idw xx xx xx xx xx". xx xx xx xx xx: use DECT ID in
Step 5.
7. Execute the command "epw 00 01 01 00".
8. Default bath file: Execute the command "default.bat"
9. Common batch file: Execute the command
"TGCA20EUEX_DEF_RevXXX_YYY.bat"(*2).
10. Country version batch file: Execute the command
"TGCA20EUEX_WW_RevXXX_YYY.bat"(*2).
11. Confirm DECT ID written in the label pated plastic bag of FLASH rom.
12. Write ID(PFPI): Write DECT ID.
• Execute the command "IDWRITE". Refer to 11.4.3. Commands.
2) Clock adjustment.
3) Battery low confirmation as below.

5
4ADDITION
4.1. VES (Virtual EEPROM Storage) LAYOUT (Handset)
[Added into original section "8.3. VES (Virtual EEPROM Storage) LAYOUT (Handset)"]
8.3. VES (Virtual EEPROM Storage) LAYOUT (Handset)
8.3.1. Scope
The purpose of this section is to describe the layout of the VES (Virtual EEPROM Storage) area in FLASH (IC4) for the Handset.
The VES area contains hardware, software, and user specific parameters. Some parameters are set during production of the
handset, some are set by the user when configuring the handset, and some during normal use of the phone.
8.3.2. Introduction
The handset uses a 128k bit VES area in FLASH (IC4) for storing volatile parameters. All parameters are set up before the
handset the factory. Some of these are vital for the operation of the hardware so a set of default parameters is programmed
before the actual hardware fine-tuning can be initiated. This document lists all default settings with a short description.
This document lists all default parameters with a short description.
8.3.3. VES area contents
MMI Setting:
MMI1 Setting:
Initial Type Description
F The data initialized by only F command
0 The data initialized by F and 0 command
1 The data initialized by F, 0 and 1 command
2 The data initialized by F, 0, 1 and 2 command
3 The data initialized by all command (F, 0, 1, 2, 3)
Country Setting Description
x Default - no specific country setting, so revert to default value.
Address Initial
Type
Name Description Default value Country
Setting
04 B0 3 EEP_Language Selected Language for LCD
GERMAN:0 ENGLISH:1 SPANISH:2 NORWEGIAN:3
FRENCH:4 ITALIAN:5 DENISH:6 DUTCH:7 SWEDISH:8
FINNISH:9
GREEK:10 TURKISH:11 HUNGARIAN:12 PORTUGUESE:13
RUSSIAN:14
POLISH:15 SLOVAKIAN:16 CZECH:17 CROATIAN:18
CATALAN:19
UKRINIAN:20 SPANISHMEX:21 SLOVENIAN:22
ESTNIAN:23 LITHUANIAN:24
LATVIAN:25 ROMANIAN:26 BULGARIAN:27
MACEDONIAN:29
ALBANIAN:30 PORTUGUESEMEX:31 ENGLISH(USA):32
HEBREW:33
ARABIC:34 PERSIA:35 HANTAI:36 HANTAI(HK):37
RUSSIAN(BX):38
BELARUS:39 KAZAKHSTAN:40 UZBEKISTAN:41
TAJIKISTAN:42
TURKMENISTAN:43 AZERBAIJAN:44 ARMENIA:45
MOLDOV:46
CANADAENGLISH:48 USSPANISH:49 USFRENCH:50
PORTUGUESE:51 ENGLISH(AZ):52
0x01 0x07
(for
BL,NL)
0x01
(for
CX,BX,U
E,ML,HK,
TW)
0x04
(for TU)
0x0A
(for GR)
0x00
(for SL)
Address Initial
Type
Name Description Default value Country
Setting
00 12 F EEP_LcdContrast LCD contrast 0x29 x

6
4.2. How to update the BBIC.
[Added into original section "11.6.1.2.1. How to update the BBIC."]
11.6.1.2.1. How to update the BBIC.
• Execute COM communicator.exe
1. Initialize COM port.(Only once at first.)
Select “Setting” o“Serial port” o“Initial settings” o“OK”.
2.Select serial port COM number.
Select “Setting” o“Serial port” o“Initial settings” o“OK”.
Fill up the “COM Option” o“OK”.
Note:
Once download is successful for a PC, this step is unnecessary next time to the PC.
Setting
Serial port
Initial settings
OK Cancel
(1) (2)
(3)
Setting
Serial port
Initial settings
OK Cancel

7
• Execute COM communicator.exe again <<Write program>>
1. Select “Addon” o“ProgramLoader”.
2. Select "Setting" o"Config".
Fill up the “ConfigSettings”.
Note:
(2) Select Baud Rate as 57600. If write error happens, select slower Baud Rate (example: 19200).
3. Select download file.
(1)
(2)
(3)
(1)
(2)

8
NM
4. Start download.
(1). Connect Unit and 3wire jig.
(2). Confirm "Turn on power to target and press download." display.
(3). Power off the unit, then power on.
(4). Press "Download" button again.
5. Finish download.
Completed dialog means "Download finished successfully!." It takes more than 20 minutes to download
( It depends on baud rate). If error message is displayed, proceed from step 3 again.
6. Continuous download.
Write next unit's software with proceeding from step 3 to Step 5.
(2)
(4)